Dell OptiPlex Micro 7010 Owners Manual

Dell OptiPlex Micro 7010 Manual

Get Dell OptiPlex Micro 7010 PDF manuals and user guides View all Dell OptiPlex Micro 7010 manuals
Add to My Manuals
Save this manual to your list of manuals

Dell OptiPlex Micro 7010 manual content summary:

  • Dell OptiPlex Micro 7010 | Owners Manual - Page 1
    OptiPlex Micro 7010 Owner's Manual Regulatory Model: D15U Regulatory Type: D15U004 March 2023 Rev. A00
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 2
    and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. © 2023 Dell Inc. or its subsidiaries. All rights reserved. Dell Technologies, Dell, and other trademarks are trademarks of Dell Inc. or its subsidiaries. Other trademarks
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 3
    8 Chapter 3: Specifications of OptiPlex Micro 7010 12 Dimensions and weight...12 Processor...12 Chipset...14 Operating system...15 Memory...15 Memory matrix...15 External ports...16 Internal slots...16 Ethernet...17 Wireless module...17 Audio...17 Storage...18 Power adapter...18 GPU-Integrated...19
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 4
    Installing the side cover...31 Front bezel...32 Removing the front bezel...32 Installing the front bezel...33 Hard drive...34 Removing the hard drive...34 Installing the hard drive...36 Solid-state drive...38 Removing the M.2 2230 solid-state drive...38 Installing the M.2 2230 solid-state drive...39
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 5
    93 Clearing BIOS (System Setup) and System passwords 93 Chapter 9: Troubleshooting...94 Dell SupportAssist Pre-boot System Performance Check diagnostics 94 Running the SupportAssist Pre-Boot System Performance Check 94 Power-Supply Unit Built-in Self-Test ...94 System-diagnostic lights...95
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 6
    Front 1 Views of OptiPlex Micro 7010 1. Power button with diagnostic LED 2. Hard-disk activity light 3. Universal audio jack 4. Two USB 3.2 Gen 1 ports 6 Views of OptiPlex Micro 7010
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 7
    in) 3. DC-in cable clip 4. USB 2.0 port with Smart Power On 5. Kensington security-cable slot and padlock ring 6. Power-adapter port 7. Service Tag label 8. DisplayPort 1.4a (HBR2) 9. HDMI 1.4b port 10. Two USB 3.2 Gen 1 ports 11. USB 2.0 port 12. RJ45 Ethernet port Views of OptiPlex Micro 7010 7
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 8
    Steps 1. Connect the keyboard and mouse. 2 Set up your computer 2. Connect to your network using a cable, or connect to a wireless network. 8 Set up your computer
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 9
    3. Connect the display. 4. Connect the power cable. Set up your computer 9
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 10
    the power button. 6. Finish operating system setup. For Ubuntu: Follow the on-screen instructions to complete the setup. For more information about installing and configuring Ubuntu, search in the Knowledge Base Resource at www.dell.com/support. For Windows: Follow the on-screen instructions to
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 11
    Technical support. It addresses performance and stabilization issues, prevents security threats, monitors, and detects hardware failures. For more information, see SupportAssist for Home PCs User's Guide at www.dell.com/ serviceabilitytools. Click SupportAssist and then, click SupportAssist for Home
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 12
    table lists the height, width, depth, and weight of your OptiPlex Micro 7010. Table 2. Dimensions and weight Description Height Values 182 mm (7.17 in.) Width The following table lists the details of the processors supported by your OptiPlex Micro 7010. 12 Specifications of OptiPlex Micro 7010
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 13
    design power differ according to the thermal mode selected in the My Dell app on your computer. Processor cache Integrated graphics 4 MB Intel UHD Graphics 710 6 MB Intel UHD Graphics 710 12 MB Intel UHD Graphics 730 20 MB Intel UHD Graphics 730 Specifications of OptiPlex Micro 7010 13
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 14
    in the My Dell app on your computer. Processor cache Integrated graphics 24 MB Intel UHD Graphics 770 24 MB Intel UHD Graphics 770 30 MB Intel UHD Graphics 770 Chipset The following table lists the details of the chipset supported by your OptiPlex Micro 7010. Table 5. Chipset Description
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 15
    MHz, dual-channel ● 64 GB, 2 x 32 GB, DDR4, 3200 MHz, dual-channel Memory matrix The following table lists the memory configurations supported on your OptiPlex Micro 7010. Table 7. Memory matrix Configuration Slot SO-DIMM1 SO-DIMM2 4 GB DDR4 4 GB 8 GB DDR4 8 GB 8 GB DDR4 4 GB 4 GB 16
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 16
    -card reader Not supported Power-adapter port ● One DC-in port with 4.50 mm barrel ● One Type-C power in (optional) Security-cable slot ● One Kensington lock slot ● One padlock ring Internal slots The following table lists the internal slots of your OptiPlex Micro 7010. Table 9. Internal
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 17
    card Audio The following table lists the audio specifications of your OptiPlex Micro 7010. Table 12. Audio specifications Description Audio controller Values Realtek ALC3246 Stereo conversion Not supported Internal audio interface High definition audio interface External audio interface
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 18
    solid-state drive 1st M.2 solid-state drive Power adapter The following table lists the power adapter specifications of your OptiPlex Micro 7010. Table 15. Power adapter specifications Description Option one Type 65 W Option two 90 W Connector dimensions: External diameter 4.50 mm 4.50 mm
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 19
    Table 15. Power adapter specifications (continued) Description Option one Internal diameter 2.90 mm Input integrated Graphics Processing Unit (GPU) supported by your OptiPlex Micro 7010. Table 16. GPU-Integrated Controller External display support Memory size Processor Intel UHD Graphics
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 20
    following table lists the environmental specifications of your OptiPlex Micro 7010. Table 20. Environmental Feature Recyclable packaging BFR/PVC-free chassis Vertical orientation packaging support Multi-Pack packaging Energy-Efficient Power Supply ENV0424 compliant Values Yes Yes No Yes Standard
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 21
    The following table lists the regulatory compliance of your OptiPlex Micro 7010. Table 21. Regulatory compliance Regulatory compliance Product Safety, EMC and Environmental Datasheets Dell Regulatory Compliance Home page Dell and the Environment Operating and storage environment This table
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 22
    www.dell.com/ regulatory_compliance. WARNING: Disconnect your computer from all power troubleshooting and repairs as authorized or directed by the Dell technical assistance team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. See the safety instructions
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 23
    field service kit when working inside any to avoid electrostatic discharge (ESD) damage. ● After removing any system component, carefully place the removed component on an anti-static mat. ● Wear shoes with non-conductive rubber soles to reduce the chance of getting electrocuted. Standby power Dell
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 24
    damage to recognize and troubleshoot is the intermittent (also ESD mat, and the hardware is known as bonding. Use only Field Service kits with a wrist strap, mat, and bonding wire. Never use parts or parts to be returned to Dell, it is critical to place these parts in anti-static
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 25
    servicing Dell products. In addition, it is critical to keep sensitive parts separate from all insulator parts while performing service stable base, and point your toes out. 2. Tighten stomach muscles. Abdominal muscles support your spine when you lift, offsetting the force of the load. 3. Lift with
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 26
    card M2x3.5 1 M.2 2230/2280 solid-state drive Internal antenna I/O module Type-C module M2x3.5 1 M3x3 3 M3x3 2 or M2x5, cross type M2x3 2 Major components of OptiPlex Micro 7010 The following image shows the major components of OptiPlex Micro 7010. 26 Working inside your computer
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 27
    1. Side cover 3. Heat sink 5. Speaker holder 7. Chassis 2. Fan assembly 4. Speaker 6. System board 8. Processor Working inside your computer 27
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 28
    9. Wireless card 11. M.2 2280 solid-state drive 10. Memory module 12. Hard-drive assembly NOTE: Dell provides a list of components and their part numbers for the original system configuration purchased. These parts are available according to warranty coverages purchased by the
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 29
    5 Removing and installing Customer Replaceable Units (CRUs) The replaceable components in this chapter are Customer Replaceable Units (CRUs). CAUTION: Customers can replace only the Customer Replaceable Units (CRUs) following the safety precautions and replacement procedures. NOTE: The images in
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 30
    Steps 1. Place your computer on its side with the side cover facing up. 30 Removing and installing Customer Replaceable Units (CRUs)
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 31
    2. Loosen the thumb-screw (6x32) that secures the side cover to the chassis. 3. Slide and lift the side cover off the chassis. Installing the side cover Prerequisites If you are replacing a component, remove the existing component before performing the installation process. About this task The
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 32
    Steps 1. Place the side cover on the chassis. 2. Align the tabs on the side cover with the slots on the chassis. 3. Slide the side cover into place towards the front of the computer. 4. Tighten the thumb-screw (6x32) that secure the side cover to the chassis. Next steps 1. Follow the procedure in
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 33
    Steps 1. Gently pry and release the front-cover tabs from the top-right, working down sequentially to the bottom-right tab. 2. Swing the front bezel outwards, away from the side cover. 3. Lift the front bezel off the side cover. Installing the front bezel Prerequisites If you are replacing a
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 34
    Steps 1. Insert the right-side front-bezel tabs into the corresponding slots on the side cover. 2. Push the left-side of the front bezel towards the side cover, snapping the tabs into position. Next steps 1. Install the side cover. 2. Follow the procedure in After working inside your computer. Hard
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 35
    Removing and installing Customer Replaceable Units (CRUs) 35
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 36
    Steps 1. Press and hold the tab that secures the hard-drive assembly to the chassis. 2. Slide and release the hard drive assembly from the chassis. 3. Lift the hard-drive assembly off the chassis. 4. Flip over the hard-drive assembly. 5. Pry the hard-drive carrier to release the tabs on the carrier
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 37
    Removing and installing Customer Replaceable Units (CRUs) 37
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 38
    Steps 1. Place the 2.5-inch hard drive into the hard-drive carrier and align the tabs on the carrier with the slots on the hard drive. 2. Snap the hard-drive carrier onto the 2.5-inch hard drive. 3. Flip over the hard-drive assembly. 4. Place the hard-drive assembly on the chassis. 5. Align the tabs
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 39
    About this task NOTE: Depending on the configuration ordered, your computer may have an M.2 2230 or an M.2 2280 solid-state drive installed in the solid-state drive slot (M.2 PCIe SSD 1) on the system board. NOTE: This procedure is applicable for computers where an M.2 2230 solid-state drive is
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 40
    Steps 1. Align the notch on the M.2 2230 solid-state drive with the tab on the solid-state drive slot (M.2 PCIe SSD 1). 2. Slide the M.2 2230 solid-state drive into the solid-state drive slot (M.2 PCIe SSD 1) on the system board. 3. Replace the screw (M2x3.5) that secures the M.2 2230 solid-state
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 41
    Steps 1. Remove the screw (M2x3.5) that secures the M.2 2280 solid-state drive to the system board 2. Slide and lift the M.2 2280 solid-state drive off the solid-state drive slot (M.2 PCIe SSD 1) on the system board. Installing the M.2 2280 solid-state drive Prerequisites If you are replacing a
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 42
    Steps 1. Align the notch on the M.2 2280 solid-state drive with the tab on the solid-state drive slot (M.2 PCIe SSD 0). 2. Slide the M.2 2280 solid-state drive into the solid-state drive slot (M.2 PCIe SSD 1) on the system board. 3. Replace the screw (M2x3.5) that secures the M.2 2280 solid-state
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 43
    Steps 1. Remove the screw mount on the system board. 2. Install the screw mount on the system board. Wireless card Removing the wireless card Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Remove the side cover. 3. Remove the hard drive, if applicable. About this
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 44
    Steps 1. Remove the screw (M2x3.5) that secures the wireless-card bracket to the wireless card. 2. Lift the wireless-card bracket off the wireless card. 3. Disconnect the antenna cables from the wireless card. 4. Slide and remove the wireless card from the wireless-card slot (M.2 WLAN). Installing
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 45
    Steps 1. Connect the antenna cables to the wireless card. Table 24. Antenna-cable color scheme Connectors on the wireless card Main Antenna-cable color Silkscreen marking White MAIN Auxiliary Black AUX △ (white triangle) ▲ (black triangle) 2. Place the wireless-card bracket on the wireless
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 46
    Speaker Removing the speaker Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Remove the side cover. About this task The following image(s) indicate the location of the speaker and provides a visual representation of the removal procedure. Steps 1. Disconnect the
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 47
    Steps 1. Connect the speaker cable to the system board. 2. Press and hold on the tab that secures the speaker to the system board. 3. Place the speaker on the system board. 4. Release the tab that secures the speaker to the system board. Next steps 1. Install the side cover. 2. Follow the procedure
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 48
    Steps 1. Press and hold the tabs that secures the fan assembly to the system board. 2. Lift the fan assembly off the system board and hold it in place. 3. Flip over the fan assembly. 4. Disconnect the fan cable from the system board. 5. Lift the fan off the fan shroud. Installing the fan
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 49
    Steps 1. Place the fan on the fan shroud. 2. Align the tabs on the fan with the slots on the fan shroud. 3. Snap the fan into place on the fan shroud. 4. Connect the fan cable to the system board. 5. Flip over the fan assembly. 6. Press and hold the tabs on the fan assembly. 7. Place the fan
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 50
    Coin-cell battery Removing the coin-cell battery Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Remove the side cover. About this task NOTE: Removing the coin-cell battery resets the BIOS settings to default. It is recommended that you note the BIOS settings before
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 51
    Steps With the positive side (+) facing up, insert the coin-cell battery into the battery socket on the system board and snap the battery into place. Next steps 1. Install the side cover. 2. Follow the procedure in After working inside your computer. Memory Removing the memory Prerequisites 1.
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 52
    Steps 1. Carefully spread apart the securing-clips on each end of the memory-module slot. 2. Grasp the memory module near the securing clip, and then gently ease the memory module out of the memory-module slot. CAUTION: To prevent damage to the memory module, hold the memory module by the edges. Do
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 53
    Steps 1. Ensure that the securing clips are in an open position 2. Align the notch on the memory module with the tab on the memory-module slot. 3. Press down on the memory module until the memory module snaps into position and the securing clip locks in place CAUTION: To prevent damage to the memory
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 54
    only. CAUTION: To avoid any potential damage to the component or loss of data, ensure that an authorized service technician replaces the Field Replaceable Units (FRUs). CAUTION: Dell Technologies recommends that this set of repairs, if needed, to be conducted by trained technical repair specialists
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 55
    Steps 1. In reverse sequential order (3>2>1) loosen the three captive screws that secure the heat sink to the system board. 2. Lift the heat sink off the system board. Installing the heat sink Prerequisites If you are replacing a component, remove the existing component before performing the
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 56
    1. Follow the procedure in Before working inside your computer. 2. Remove the side cover. About this task NOTE: The optional PS2 module comes with a custom Dell adapter cable that is required to access the PS2 I/O ports. Plug in the adapter cable to access the PS2 I/O and COM ports of your computer
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 57
    The following images indicate the location of the optional I/O module and provide a visual representation of the removal procedure. Steps 1. Remove the two (M3x3) screws that secure the optional I/O module (HDMI/DP/PS2) or two (M2x5) cross type screws that secure the optional I/O module (VGA/Serial
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 58
    are replacing a component, remove the existing component before performing the installation procedure. About this task NOTE: The optional PS2 module comes with a custom Dell adapter cable that is required to access the PS2 I/O ports. Plug in the adapter cable to access the PS2 I/O and COM ports of
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 59
    2. Insert the optional I/O module into its slot from the inside of your computer. 3. Connect the I/O cable to the connector on the system board. 4. Replace the two (M3x3) screws that secure the optional I/O module (HDMI/DP/PS2) or two (M2x5) cross type screws that secure the optional I/O module (VGA
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 60
    4. Disconnect the Type-C DisplayPort cable from the system board. 5. Disconnect the Type-C USB cable from the system board. 6. Disconnect the Type-C power cable from the system board. 7. Disconnect the Type-C signal cable from the system board. 8. Remove the optional Type-C module from the computer
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 61
    I/O module. 2. Connect the Type-C DisplayPort cable to the system board. 3. Connect the Type-C USB cable to the system board. 4. Connect the Type-C power cable to the system board. 5. Connect the Type-C signal cable to the system board. 6. Insert the optional Type-C module into its slot from the
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 62
    Processor Removing the processor Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Remove the side cover. 3. Remove the hard drive, if applicable. 4. Remove the speaker. 5. Remove the fan. 6. Remove the heat sink. About this task NOTE: The heat sink may become hot
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 63
    Steps 1. Press the release lever down and then push it away from the processor to release it from the securing tab. 2. Extend the release lever completely and open the processor cover. CAUTION: When removing the processor, do not touch any of the pins inside the socket or allow any objects to fall
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 64
    Steps 1. Ensure that the release lever on the processor socket is fully extended in the open position. NOTE: The pin-1 corner of the processor has a triangle that aligns with the triangle on the pin-1 corner on the processor socket. When the processor is properly seated, all four corners are aligned
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 65
    System board Removing the system board Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Remove the side cover. 3. Remove the hard drive, if applicable. 4. Remove the coin-cell battery. 5. Remove the M.2 2230 solid-state drive or M.2 2280 solid-state drive, whichever
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 66
    )/HDMI 2.1 Port/Type-C DisplayPort) 6. Type-C signal connector 7. Type-C USB connector 8. Optional PS/2, serial port connector 9. Processor socket 10. Type-C power connector 11. Fan connector 12. Internal speaker connector 13. Memory-module slots The following image(s) indicate the location of the
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 67
    Steps 1. Remove the screw (M3x5) that secures the speaker-support bracket to the system board. 2. Lift the speaker-support bracket off the system board. 3. Remove the four screws (M3x5) that secures the system board to the chassis. 4. Remove the two screws (M3x4) that secures
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 68
    )/HDMI 2.1 Port/Type-C DisplayPort) 6. Type-C signal connector 7. Type-C USB connector 8. Optional PS/2, serial port connector 9. Processor socket 10. Type-C power connector 11. Fan connector 12. Internal speaker connector 13. Memory-module slots The following image(s) indicate the location of the
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 69
    Removing and installing Field Replaceable Units (FRUs) 69
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 70
    the chassis. 5. Replace the two screws (M3x4) that secures the system board to the chassis. 6. Place the speaker-support bracket on the system board. 7. Align the screw holes on the speaker-support bracket to the screw holes on the system board. 8. Replace the screw (M3x5) that secures the speaker
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 71
    of the antenna module (black cable) and provides a visual representation of the removal procedure. Steps 1. Remove the antenna cable from the routing guides on the chassis. 2. Loosen the captive screw that secures the antenna module (while cable) to the chassis. 3. Lift the antenna module (black
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 72
    hole on the chassis. 3. Tighten the captive screw that secures the antenna module (black cable) to the chassis. 4. Route the antenna cable through the routing guides on the chassis. Next steps 1. Install the system board NOTE: The system board can be installed with the memory, coin-cell battery, and
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 73
    of the antenna module (white cable) and provides a visual representation of the removal procedure. Steps 1. Remove the antenna cable from the routing guides on the chassis and system board. 2. Remove the screw (M3x3) that secures the antenna module (white cable) to the chassis. 3. Listen the
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 74
    chassis. 4. Replace the screw (M3x3) that secures the antenna module (white cable) to the chassis. 5. Route the antenna cable through the routing guides on the chassis and system board. Next steps 1. Install the hard drive, if applicable. 2. Install the side cover. 74 Removing and installing Field
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 75
    3. Follow the procedure in After working inside your computer. Removing SMA antenna assembly Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the side cover. 3. Remove the hard drive, if applicable. 4. Remove the wireless card. About this task The following
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 76
    Steps 1. Remove the SMA antenna assembly cables from the routing guides on the chassis. 2. Remove the screw (M3x3) that secures the SMA antenna assembly to the chassis. 3. Push the SMA antenna assembly inside from the opening
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 77
    Installing SMA antenna assembly Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The following images indicate the location of SMA antenna assembly and provide a visual representation of the removal procedure.
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 78
    6. Replace the screw (M3x3) that secures the SMA antenna assembly to the chassis. 7. Route the SMA antenna assembly cables through the routing guides on the chassis. Next steps 1. Install the wireless card. 2. Install the hard drive, if applicable. 3. Install the side cover. 4. Follow the procedure
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 79
    the supported operating systems along with instructions on how to install the drivers. Operating system Your OptiPlex Micro 7010 supports the bit Drivers and downloads When troubleshooting, downloading or installing drivers it is recommended that you read the Dell Knowledge Base article, Drivers
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 80
    8 BIOS setup CAUTION: Unless you are an expert computer user, do not change the settings in the BIOS Setup program. Certain changes can make your computer work incorrectly. NOTE: Depending on the computer and its installed devices, the items listed in this section may or may not be displayed. NOTE
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 81
    the Asset Tag of the computer. Displays the manufacture date of the computer. Displays the ownership date of the computer. Displays the express service code of the computer. Displays the Ownership Tag of the computer. Displays whether the Signed Firmware Update is enabled on your computer. Displays
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 82
    Table 26. System setup options-System information menu (continued) Overview DIMM 2 Size Displays the DIMM 2 memory size. Devices Information Video Controller Displays the video controller type of the computer. Video Memory Displays the video memory information of the computer. Wi-Fi Device
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 83
    Table 28. System setup options-Integrated Devices menu (continued) Integrated Devices Memory Mapped I/O above 4 Gig Allows 64-bit capable PCI devices to be decoded in above 4 GB address space, freeing up memory resources under 4 GB. By default, the this option is enabled. Audio Enable Audio
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 84
    feature. By default, the HTTPs Boot option is enabled. HTTPs Boot Mode With Auto Mode, the HTTPs Boot extracts Boot URL from the DHCP. With Manual Mode, the HTTPs Boot reads Boot URL from the user-provided data. By default, the Auto Mode option is enabled. 84 BIOS setup
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 85
    Table 32. System setup options-Power menu Power USB Wake Support Enable USB Wake Support When enabled, you can use the USB devices like a mouse or keyboard to wake your computer from standby. By default, the option is enabled. AC
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 86
    permanently disable the BIOS module interface of the optional Absolute Persistence Module service from Absolute software. By default, the Enable Absolute option is enabled for computer and internal hard drive passwords when powered on from the off state. By default, the Disabled option is enabled.
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 87
    Master Password Lockout When enabled, this will disable the master password support. By default, the option is disabled. Allow Non-Admin PSID Revert Threshold setup option and local Service OS does not boot or is not installed. By default, the option is enabled. Dell Auto OS Recovery Threshold
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 88
    storage device. By default, the option is disabled. SERR Messages Enable or disable SERR messages. By default, the option is enabled. First Power On Date Set ownership date By default, the option is disabled. Diagnostics Enables OS agent request to schedule onboard diagnostics. By default, the
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 89
    disable adapter warnings to display a warning message if a power adapter with too little power capacity is detected. By default, the Adapter Warnings default, the option is disabled. DMA Protection Enable Pre-Boot DMA support. Controls Pre-Boot DMA protection for both internal and external ports.
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 90
    power dell.com/support. 2. Click Product support. In the Search support box, enter the Service Tag of your computer, and then click Search. NOTE: If you do not have the Service Tag, use the SupportAssist feature to automatically identify your computer. You can also use the product ID or manually
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 91
    you saved the BIOS update file. 8. Double-click the BIOS update file icon and follow the on-screen instructions. For more information, search in the Knowledge Base Resource at www.dell.com/support. Updating the BIOS in Linux and Ubuntu To update the system BIOS on a computer that is installed with
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 92
    FAT32 file system (key does not have to be bootable) ● BIOS executable file that you downloaded from the Dell Support website and copied to the root of the USB drive ● AC power adapter that is connected to the computer ● Functional computer battery to flash the BIOS Perform the following steps to
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 93
    Locked. About this task To enter the System Setup, press F12 immediately after a power-on or reboot. Steps 1. In the System BIOS or System Setup screen, To clear the system or BIOS passwords, contact Dell technical support as described at www.dell.com/contactdell. NOTE: For information on how to
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 94
    Dell. Power-Supply Unit Built-in Self-Test Built-in Self-Test (BIST) helps determine if the power-supply unit is working. To run self-test diagnostics on the power-supply unit of a desktop or all-in-one computer, search in the Knowledge Base Resource at www.dell.com/support. 94 Troubleshooting
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 95
    of your OptiPlex Micro 7010. Table 43. System-diagnostic lights Blinking pattern Amber White 1 1 Problem description TPM flea power by pressing and holding down power button for 3~5 seconds. 2 1 CPU failure ● Run the Dell Support Assist/Dell Diagnostics tool. ● If problem persists,
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 96
    (AC, battery, coin cell) and drain flea power by pressing and holding down power button 3~5 seconds to ensure all power are drained. ● Run "BIOS recovery from USB", and the instructions are in the website Dell support. ● If problem persists, replace the system board. Timeout waiting on
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 97
    to create a recovery drive to troubleshoot and fix problems that may occur with Windows. Dell proposes multiple options for recovering Windows operating system on your Dell PC. For more information. see Dell Windows Backup Media and Recovery Options. Wi-Fi power cycle About this task If your
  • Dell OptiPlex Micro 7010 | Owners Manual - Page 98
    about your computer through videos, manuals and documents. Your Dell computer is uniquely identified by a Service Tag or Express Service Code. To view relevant support resources for your Dell computer, enter the Service Tag or Express Service Code at www.dell.com/support. For more information on
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
OptiPlex Micro 7010
Owner's Manual
Regulatory Model: D15U
Regulatory Type: D15U004
March 2023
Rev. A00