Dell OptiPlex Small Form Factor 7010 Owners Manual

Dell OptiPlex Small Form Factor 7010 Manual

Get Dell OptiPlex Small Form Factor 7010 PDF manuals and user guides View all Dell OptiPlex Small Form Factor 7010 manuals
Add to My Manuals
Save this manual to your list of manuals

Dell OptiPlex Small Form Factor 7010 manual content summary:

  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 1
    OptiPlex Small Form Factor 7010 Owner's Manual Regulatory Model: D17S Regulatory Type: D17S003 March 2023 Rev. A00
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 2
    and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. © 2023 Dell Inc. or its subsidiaries. All rights reserved. Dell Technologies, Dell, and other trademarks are trademarks of Dell Inc. or its subsidiaries. Other trademarks
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 3
    of OptiPlex Small Form Factor 7010 18 Dimensions and weight...18 Processor...18 Chipset...20 Operating system...20 Memory...20 Memory matrix...21 External ports...21 Internal slots...22 Ethernet...22 Wireless module...22 Audio...23 Storage...23 Power ratings...24 Power supply connector
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 4
    button...70 Intrusion switch...71 Removing the intrusion switch...71 Installing the Intrusion switch ...72 Power-supply unit...73 Removing the power-supply unit...73 Installing the power-supply unit...75 Processor fan and heat-sink assembly...76 Removing the processor fan and heat-sink assembly
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 5
    Clearing BIOS (System Setup) and System passwords 114 Chapter 9: Troubleshooting...115 Dell SupportAssist Pre-boot System Performance Check diagnostics 115 Running the SupportAssist Pre-Boot System Performance Check 115 Power-Supply Unit Built-in Self-Test ...115 System-diagnostic lights...116
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 6
    1 6 Views of OptiPlex Small Form Factor 7010
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 7
    Views of OptiPlex Small Form Factor 7010 Display Views of OptiPlex Small Form Factor 7010 7
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 8
    1. Power button with diagnostic LED 2. Hard-drive activity light 3. Universal audio jack port 4. Two USB 2.0 ports 5. Two USB 3.2 Gen 1 ports 6. Slim optical drive 8 Views of OptiPlex Small Form Factor 7010
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 9
    Back Views of OptiPlex Small Form Factor 7010 9
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 10
    1 ports 4. Two USB 2.0 ports with Smart Power On 5. Two expansion card slots 6. Power cable connector 7. Power-supply diagnostics light 8. Padlock ring 9. RJ45 Ethernet port 1.4a (HBR3)/VGA) (optional) 13. Service Tag label 14. One Serial port (optional) 10 Views of OptiPlex Small Form Factor 7010
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 11
    Steps 1. Connect the keyboard and mouse. 2 Set up your computer Set up your computer 11
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 12
    2. Connect to your network using a cable, or connect to a wireless network. 12 Set up your computer
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 13
    3. Connect the display. Set up your computer 13
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 14
    4. Connect the power cable. 14 Set up your computer
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 15
    5. Press the power button. Set up your computer 15
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 16
    6. Finish operating system setup. 16 Set up your computer
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 17
    setup. For more information about installing and configuring Ubuntu, search in the Knowledge Base Resource at www.dell.com/support. For Windows: Follow the on-screen instructions to complete the setup. When setting up, Dell recommends that you: ● Connect to a network for Windows updates. NOTE: If
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 18
    manufacturing variability. ● Weight (minimum): 3.68 kg (8.10 lb) ● Weight (maximum): 4.87 kg (10.72 lb) Processor The following table lists the details of the processors supported by your OptiPlex Small Form Factor 7010. 18 Specifications of OptiPlex Small Form Factor 7010
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 19
    GHz 5.00 GHz Performance-cores frequency Processor base frequency 3.40 GHz Maximum turbo frequency 4.50 GHz Efficient-cores frequency Processor NA base frequency Maximum NA turbo frequency Processor cache NA 6 MB Intel UHD Graphics 710 Specifications of OptiPlex Small Form Factor 7010 19
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 20
    bus width 64-bit/128-bit Flash EPROM 32 MB RPMC+16 MB nRPMC PCIe bus Up to Gen3 Operating system Your OptiPlex Small Form Factor 7010 supports the following operating systems: ● Windows 11 Home ● Windows 11 Pro ● Windows 11 Pro Downgrade (Windows 10 image) ● Windows 11 Pro National Education
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 21
    ● One HDMI 1.4b port (Rear) NOTE: The maximum resolution supported by HDMI 1.4b port is 1920 x 1200 @ 60 Hz. Media-card reader Not supported Power-adapter port Not supported Security-cable slot ● Security-cable slot (for Kensington locks) Specifications of OptiPlex Small Form Factor 7010 21
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 22
    in the Knowledge Base Resource at www.dell.com/support. SATA slots Two SATA 3.0 slots for 2.5-inch/3.5-inch hard drive and slim optical drive Ethernet The following table lists the wired Ethernet Local Area Network (LAN) specifications of your OptiPlex Small Form Factor 7010. Table 9. Ethernet
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 23
    output: Average speaker output 2 W Peak speaker output 2.5 W Subwoofer output Not supported Microphone Internal Mic not available Storage This section lists the storage options on your OptiPlex Small Form Factor 7010. Table 12. Storage matrix Storage M.2 solid-state drive M.2 solid-state
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 24
    to 1 TB Up to 1 TB Power ratings The following table lists the power rating specifications of OptiPlex Small Form Factor 7010. Table 14. Power ratings Description Type Option one Option two 180 W internal power supply unit (PSU), 300 W internal power supply unit (PSU), 85% Efficient, 80 Plus
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 25
    to 158°F) Power supply connector The following table lists the Power supply connector specifications of your OptiPlex Small Form Factor 7010. Table 15. Power supply connector 180 W supported by your OptiPlex Small Form Factor 7010. Table 16. GPU-Integrated Controller External display support
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 26
    . For more information about using DisplayPort Multi-Stream Transport, see www.dell.com/support. Hardware security The following table lists the hardware security of your OptiPlex Small Form Factor 7010. Table 20. Hardware security Hardware security Kensington security-cable slot Padlock loop
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 27
    of your OptiPlex Small Form Factor 7010. Table 21. Environmental Feature Values Recyclable packaging Yes BFR/PVC-free No Vertical orientation packaging support No Multi-Pack packaging Yes Energy-Efficient Power Supply Standard ENV0424 compliant Yes NOTE: Wood‐based fiber packaging
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 28
    may impact the performance of specific components. * Measured using a random vibration spectrum that simulates user environment. † Measured using a 2 ms half-sine pulse. 28 Specifications of OptiPlex Small Form Factor 7010
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 29
    www.dell.com/ regulatory_compliance. WARNING: Disconnect your computer from all power troubleshooting and repairs as authorized or directed by the Dell technical assistance team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. See the safety instructions
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 30
    any disassembly instructions. Observe power Dell products with standby power must be unplugged before you open the case. Systems that incorporate standby power are essentially powered while turned off. The internal power problems or a shortened product life span. As the industry pushes for lower power
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 31
    of damage to recognize and troubleshoot is the intermittent (also ESD mat, and the hardware is known as bonding. Use only Field Service kits with a wrist strap, mat, and bonding wire. Never use wireless parts or parts to be returned to Dell, it is critical to place these parts in anti-static
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 32
    servicing Dell products. In addition, it is critical to keep sensitive parts separate from all insulator parts while performing service . Keep your feet apart for a stable base, and point your toes out. 2. Tighten stomach muscles. Abdominal muscles support your spine when you lift, offsetting the
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 33
    supporting bracket M2x2 1 2.5-inch Hard-drive M3x3.5 4 3.5-inch Hard-drive #6-32 4 Serial/VGA module M2x5 2 DP/HDMI/Type-C module M3x3 2 SD-card reader M3x5 1 WLAN card M2x3 1 Processor-fan and heat-sink Captive 4 assembly Voltage regulator heat-sink Captive 4 Power-supply
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 34
    Table 24. Screw list (continued) Component Screw type System board #6-32 Quantity 5 Screw image Major components of OptiPlex Small Form Factor 7010 The following image shows the major components of OptiPlex Small Form Factor 7010. 34 Working inside your computer
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 35
    Working inside your computer 35
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 36
    sink and fan assembly 5. Wireless card 7. System board 9. Power-supply unit 11. Expansion card 13. Processor 2. Hard-drive assembly 4. Memory module 6. M.2 solid-state drive 8. Front bezel 10. Chassis 12. Optical drive 14. Speaker NOTE: Dell provides a list of components and their part numbers for
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 37
    5 Removing and installing Customer Replaceable Units (CRUs) The replaceable components in this chapter are Customer Replaceable Units (CRUs). CAUTION: Customers can replace only the Customer Replaceable Units (CRUs) following the safety precautions and replacement procedures. NOTE: The images in
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 38
    Installing the side cover Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The following image indicates the location of the side cover and provides a visual representation of the installation procedure.
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 39
    Steps 1. Gently pry and release the front-bezel tabs sequentially from the top. 2. Rotate the front bezel outward from the chassis and remove the front bezel. Installing the front bezel Prerequisites If you are replacing a component, remove the existing component before performing the installation
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 40
    Steps 1. Align the front-cover tabs with the slots on the chassis. 2. Rotate the front cover towards the chassis and snap it into place. Next steps 1. Install the side cover. 2. Follow the procedure in After working inside your computer. Hard drive 2.5-inch hard drive Removing the 2.5-inch hard
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 41
    About this task The following image indicates the location of the 2.5-inch hard-drive assembly and provide a visual representation of the removal procedure. Steps 1. Disconnect the data and power cables from the hard drive. Removing and installing Customer Replaceable Units (CRUs) 41
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 42
    2. Remove the screw (#6-32) that secures the hard drive carrier to the chassis. 3. Remove the four screws (M3x3.5) that secure the hard drive to the hard-drive carrier. 4. Slide and lift the 2.5-inch hard drive off the hard-drive carrier. NOTE: Note the orientation or the SATA connector marking on
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 43
    the hard-drive carrier into place. 4. Replace the screw (#6-32) to secure the hard-drive carrier to the chassis. 5. Connect the data and power cables to the connectors on the hard drive. Next steps 1. Install the side cover. 2. Follow the procedure in After working inside your computer. 3.5-inch
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 44
    44 Removing and installing Customer Replaceable Units (CRUs)
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 45
    Steps 1. Disconnect the data and power cables from the hard drive. 2. Remove the two screws (6-32) that secure the hard-drive carrier to the chassis. 3. Slide the hard-drive carrier away
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 46
    46 Removing and installing Customer Replaceable Units (CRUs)
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 47
    carrier onto the disk-drive cage. 4. Replace the two screws (6-32) to secure the hard drive carrier on the chassis. 5. Connect the data and power cables to the connectors on the hard drive. Next steps 1. Install the side cover. 2. Follow the procedure in After working inside your computer. Disk
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 48
    About this task The following image indicates the location of the disk-drive cage and provides a visual representation of the removal procedure. 48 Removing and installing Customer Replaceable Units (CRUs)
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 49
    If the optical drive is installed, remove the data and power cables from the routing points on the disk-drive cage. cage and place it on the chassis. 5. If the optical drive is installed, disconnect the power and data cables from the connectors on the optical drive. 6. Lift the disk-drive cage away
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 50
    50 Removing and installing Customer Replaceable Units (CRUs)
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 51
    . 2. If the optical drive is installed, connect the data and power cable to the connectors on the optical drive. 3. Hold the disk in place. 6. If the optical drive is installed, route the power and data cables through the routing guide on the disk-drive cage. Next steps 1. Install the 3.5-inch
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 52
    About this task The following image indicates the location of the optical-drive assembly and provides a visual representation of the removal procedure. Steps 1. Remove the single (M2x2) screw to release the optical drive from the disk-drive cage. 2. Slide the optical drive out of the disk-drive
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 53
    About this task The following image indicates the location of the optical drive and provides a visual representation of the installation procedure. Steps 1. Slide the optical drive into the disk-drive cage until it snaps into place. 2. Install the single (M2x2) screw to secure the optical drive
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 54
    Memory Removing the memory Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Remove the side cover. 3. Remove the front bezel. 4. Remove the 2.5-inch hard drive if applicable. 5. Remove the 3.5-inch hard drive if applicable. 6. Remove the disk-drive cage. About this
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 55
    Installing the memory Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The following image indicates the location of the memory modules and provides a visual representation of the installation procedure.
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 56
    Solid-state drives Solid-state drive (half-length) Removing the M.2230 solid-state drives Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Remove the side cover. 3. Remove the front bezel. 4. Remove the 2.5-inch hard drive if applicable. 5. Remove the 3.5-inch hard
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 57
    NOTE: The following image indicates the location to install the solid-state drive screw mount based on form factor. The following image indicates the location of the M.2230 solid-state drives and provides a visual representation of the installation procedure. Steps 1. Peel off the protection
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 58
    2. Peel off the protection mylar on the thermal pad. 3. Align the notch on the M.2230 solid-state drive with the tab on the M.2 card slot on the system board. 4. Slide the M.2230 solid-state drive into the M.2 card slot on the system board. 5. Replace the screw (M2x3.5) to secure the M.2230 solid-
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 59
    2230 solid-state drive is removed first. NOTE: The following image indicates the location to install the solid-state drive screw mount based on form factor. The following image indicates the location of the M.2280 solid-state drive and provides a visual representation of the installation procedure
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 60
    NOTE: The thermal pad is re-usable. The thermal pad is pre-installed on systems shipped with solid-state drive. If the solid-state drive is purchased separately, the thermal pad is not bundled with the solid-state drive kit and is to be purchased separately. 2. Peel off the protection mylar on the
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 61
    Steps 1. Remove the (M2x3.5) screw that secures the wireless card bracket to the system board. 2. Slide and lift the wireless card bracket away from the wireless card. 3. Disconnect the antenna cables from the wireless card. 4. Slide and remove the wireless card from the connector on the system
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 62
    Steps 1. Connect the antenna cables to the wireless card. The following table provides the antenna-cable color scheme for the wireless card of your computer. CONNECTORS ON THE WIRELESS CARD Main (white triangle) Auxiliary (black triangle) ANTENNA-CABLE COLOR White Black 2. Slide and place the
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 63
    indicates the location of the graphics card and provides a visual representation of the removal procedure. Steps 1. Push the securing tab on the graphics-card support bracket and rotate the bracket to move it away from the chassis. Removing and installing Customer Replaceable Units (CRUs) 63
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 64
    alignment post, connect the card in the connector and press down firmly. Ensure that the card is firmly seated. 3. Rotate the graphics-card support bracket that connects the graphics card. Next steps 1. Install the disk-drive cage. 2. Install the 3.5-inch hard drive if applicable. 64 Removing and
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 65
    3. Install the 2.5-inch hard drive if applicable. 4. Install the front bezel. 5. Install the side cover. 6. Follow the procedure in After working inside your computer. Internal speaker Removing the speaker Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Remove the
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 66
    Steps 1. Press the tab on the speaker and slide the speaker into the slot on the chassis until it snaps into place. 2. Connect the speaker cable to the connector on the system board. Next steps 1. Install the side cover. 2. Follow the procedure in After working inside your computer. Coin-cell
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 67
    Steps 1. Push the coin-cell battery-release lever on the coin-cell battery socket to release the coin-cell battery out of the socket. 2. Remove the coin-cell battery. Installing the coin-cell battery Prerequisites If you are replacing a component, remove the existing component before performing the
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 68
    Steps Insert the coin-cell battery into the socket with the positive side (+) label facing up and snap the battery in the socket. Next steps 1. Install the side cover. 2. Follow the procedure in After working inside your computer. 68 Removing and installing Customer Replaceable Units (CRUs)
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 69
    of data, ensure that an authorized service technician replaces the Field Replaceable Units (FRUs). CAUTION: Dell Technologies recommends that this set of About this task The following image indicates the location of the power button and provides a visual representation of the removal procedure.
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 70
    a component, remove the existing component before performing the installation procedure. About this task The following image indicates the location of the power button and provides a visual representation of the installation procedure. 70 Removing and installing Field Replaceable Units (FRUs)
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 71
    button into the slot on the chassis. 2. Connect the power button cable to the connector on the system board. Next steps 1. Install the side cover. 2. Follow the procedure in After working inside your computer. Intrusion
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 72
    Steps 1. Remove the intrusion-switch cable from the routing guides on the chassis. 2. Disconnect the intrusion-switch cable from the connector on the system board. 3. Slide and lift the Intrusion switch away from the computer.
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 73
    the side cover. 2. Follow the procedure in After working inside your computer. Power-supply unit Removing the power-supply unit CAUTION: The information in this section is intended for authorized service technicians only. Prerequisites 1. Follow the procedure in Before working inside your computer
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 74
    from their connectors on the system board. 2. Unroute the power-supply cables from the routing guides on the chassis. 3. Remove the three screws (M6-32) that secure the power-supply unit to the chassis. 4. Slide and lift the power-supply unit off the chassis. 74 Removing and installing Field
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 75
    in this section is intended for authorized service technicians only. Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The following image indicates the location of the power-supply unit and provides a visual
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 76
    secure the power-supply unit to the chassis. 3. Route the power-supply cables through their routing guides on the chassis. 4. Connect the power-supply cables to : The information in this section is intended for authorized service technicians only. Prerequisites 1. Follow the procedure in Before
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 77
    system board. Installing the processor fan and heat-sink assembly CAUTION: The information in this section is intended for authorized service technicians only. Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 78
    your computer. Processor Removing the processor fan and heat-sink assembly CAUTION: The information in this section is intended for authorized service technicians only. Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Remove the side cover. 3. Remove the front bezel
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 79
    lift the processor from the processor socket. Installing the processor CAUTION: The information in this section is intended for authorized service technicians only. Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 80
    inside your computer. Internal antenna kit Removing the internal antenna kit CAUTION: The information in this section is intended for authorized service technicians only. Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Remove the side cover. 3. Remove the front bezel
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 81
    6. Remove the disk-drive cage. 7. Remove the wireless card if applicable. About this task The following image indicates the location of the internal antenna kit and provides a visual representation of the removal procedure. Removing and installing Field Replaceable Units (FRUs) 81
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 82
    from the chassis. 3. Unroute the internal antenna kit cable from the routing guides on the chassis 4. Gently pull the internal antenna kit cable out from the CAUTION: The information in this section is intended for authorized service technicians only. Prerequisites If you are replacing a component,
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 83
    Removing and installing Field Replaceable Units (FRUs) 83
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 84
    White Black 3. Replace the two screws (M3x3) that secures the internal antennas to the chassis. 4. Route the internal-antenna cable through the routing guides on the chassis. Next steps 1. Install the wireless card if applicable. 2. Install the disk-drive cage. 3. Install the 3.5-inch hard drive if
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 85
    inside your computer. SMA Antenna Removing the external SMA antenna kit CAUTION: The information in this section is intended for authorized service technicians only. Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Remove the side cover. 3. Remove the front bezel
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 86
    3. Remove the antenna cables from routing guides on the system board. 4. Remove the external SMA antenna kit off the system board. Installing the SMA antenna kit CAUTION: The information in this section is intended for authorized service technicians only. Prerequisites If you are replacing a
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 87
    on the back of the chassis. 5. Install the nut and washer to secure the antennas to the chassis. 6. Route the antenna cables through the routing guides on the system board. 7. Press the antenna cable into the clip on the system board. Next steps 1. Install the wireless card if applicable. 2. Install
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 88
    Steps 1. Remove the two (M2x5) cross-type screws that secure the serial module to the chassis. 2. Disconnect the serial-module cable from the connector on the system board. 3. Lift the serial module off the system board. Installing the serial module Prerequisites If you are replacing a component,
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 89
    2. Follow the procedure in After working inside your computer. VGA module Removing the VGA module Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Remove the side cover. About this task The following image indicates the location of the VGA module and provides a visual
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 90
    Steps 1. Using a screwdriver, remove the VGA module cover from the chassis. NOTE: This step is applicable only when the VGA module is being installed for the first time. 2. Connect the VGA-module cable to the connector (VIDEO) on the system board. 3. Insert the VGA module into the slot on the
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 91
    Steps 1. Remove the two (M3x3) screws that secure the DP module to the chassis. 2. Disconnect the DP-module cable from the connector on the system board. 3. Lift the DP module off the system board. Installing the DP module Prerequisites If you are replacing a component, remove the existing component
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 92
    Steps 1. Using a screwdriver, remove the DP module cover from the chassis. NOTE: This step is applicable only when the DP module is being installed for the first time. 2. Connect the DP-module cable to the connector (VIDEO) on the system board. 3. Insert the DP module into the slot on the chassis.
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 93
    Steps 1. Remove the two (M3x3) screws that secure the HDMI module to the chassis. 2. Disconnect the HDMI-module cable from the connector on the system board. 3. Lift the HDMI module off the system board. Installing the HDMI module Prerequisites If you are replacing a component, remove the existing
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 94
    Steps 1. Using a screwdriver, remove the HDMI module cover from the chassis. NOTE: This step is applicable only when the HDMI module is being installed for the first time. 2. Connect the HDMI-module cable to the connector (VIDEO) on the system board. 3. Insert the HDMI module into the slot on the
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 95
    cable 13. PCIe x16 slot (SLOT 2) 15. Coin-cell battery socket 17. Video cable 2. Processor-power cable 4. UDIMM slots From the left (a>b): DIMM 1 DIMM 2 6. System-power cable 8. M.2 WLAN slot 10. Optical-drive/hard-drive data cable (SATA 1) 12. Internal-speaker cable 14. PCIe x1 slot (SLOT 1) 16
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 96
    96 Removing and installing Field Replaceable Units (FRUs)
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 97
    Steps 1. Remove the screw (6-32) that secures the front I/O bracket to the chassis. 2. Rotate and remove the front I/O-bracket from the chassis 3. Disconnect all the cables that are connected to the system board. 4. Remove the seven (#6-32) screws that secure the system board to the chassis.
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 98
    cable 13. PCIe x16 slot (SLOT 2) 15. Coin-cell battery socket 17. Video cable 2. Processor-power cable 4. UDIMM slots From the left (a>b): DIMM 1 DIMM 2 6. System-power cable 8. M.2 WLAN slot 10. Optical-drive/hard-drive data cable (SATA 1) 12. Internal-speaker cable 14. PCIe x1 slot (SLOT 1) 16
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 99
    Removing and installing Field Replaceable Units (FRUs) 99
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 100
    Steps 1. Align and lower the system board into the system until the stand-off points at the back of the system board align with those on the chassis. 2. Replace the seven (#6-32) screws to secure the system board to the chassis. 3. Route and connect all the cables that you disconnected from the
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 101
    4. Place and align the front I/O-bracket with I/O slot on the chassis. 5. Replace the screw (#6-32) that secures the front I/O-bracket to the chassis. Next steps 1. Install the processor. 2. Install the heat-sink and fan assembly. 3. Install the WLAN card. 4. Install the solid-state drive. 5.
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 102
    the supported operating systems along with instructions on how to install the drivers. Operating system Your OptiPlex Small Form Factor 7010 supports the and downloads When troubleshooting, downloading or installing drivers it is recommended that you read the Dell Knowledge Base article, Drivers
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 103
    configuration information. ● Set or change a user-selectable option, such as the user password, type of hard drive installed, and enabling or disabling base devices. Entering BIOS setup program About this task Turn on (or restart) your computer and press F2 immediately. Navigation keys NOTE: For
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 104
    26. System setup options-System information menu General-System Information System Information BIOS Version Displays the BIOS version number. Service Tag Displays the Service Tag of the computer. Asset Tag Displays the Asset Tag of the computer. Ownership Tag Displays the ownership tag
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 105
    Table 26. System setup options-System information menu (continued) General-System Information Processor L3 Cache Displays the Processor L2 Cache size. Microcode Version Displays whether the microcode version. Intel Hyper-Threading Capable Displays whether the computer is Intel Hyper-Threading
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 106
    enabled by default. Table 32. System setup options-Power Power USB PowerShare This option is disabled by default. USB Wake Support The option is enabled by default. AC Behavior The Power Off option is enabled by default. Active State Power Management The option Auto is enabled by default
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 107
    Password Bypass Set the minimum characters allowed for password. When enabled, this always prompts for computer and internal hard drive passwords when powered on from the off state. By default, the Disabled option is enabled. Password Changes Enable Non-Admin Password Changes Enable or disable
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 108
    disable the master password support. By default, the option Service OS does not boot or is not installed. By default, the option is enabled. Dell Service Tag Display the Service Tag of the computer. Asset Tag Create a computer Asset Tag. Wake on LAN/WLAN Enable or disable the computer to power
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 109
    Days. By default, the option is disabled. SERR Messages Enable or disable SERR messages. By default, the option is enabled. First Power On Date Diagnostics Power-on-Self-Test Automatic Recovery The Set Ownership Date is disabled by default. The option OS Agent Requests The option is enabled by
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 110
    . DMA Protection Enable Pre-Boot DMA Support Enable OS Kernel DMA Support The option is enabled by default. and core frequency, decreasing average power consumption and heat production. By By default, the option is enabled. PCIe Resizable Base Address Register This option is disabled by default.
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 111
    you saved the BIOS update file. 8. Double-click the BIOS update file icon and follow the on-screen instructions. For more information, search in the Knowledge Base Resource at www.dell.com/support. Updating the BIOS in Linux and Ubuntu To update the system BIOS on a computer that is installed with
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 112
    For more information on this subject, search in the Knowledge Base Resource at www.dell.com/support. BIOS Update You can run the BIOS update file from file that you downloaded from the Dell Support website and copied to the root of the USB drive ● AC power adapter that is connected to the
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 113
    new System or Admin Password only when the status is in Not Set. About this task To enter the system setup, press F12 immediately after a power-on or reboot. Steps 1. In the System BIOS or System Setup screen, select Security and press Enter. The Security screen is displayed. 2. Select System/Admin
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 114
    Clearing BIOS (System Setup) and System passwords About this task To clear the system or BIOS passwords, contact Dell technical support as described at www.dell.com/contactdell. NOTE: For information on how to reset Windows or application passwords, refer to the documentation accompanying Windows or
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 115
    problems Dell. Power-Supply Unit Built-in Self-Test Built-in Self-Test (BIST) helps determine if the power-supply unit is working. To run self-test diagnostics on the power-supply unit of a desktop or all-in-one computer, search in the Knowledge Base Resource at www.dell.com/support. Troubleshooting
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 116
    3 7 4 1 4 2 Problem description TPM Detection Failure Unrecoverable SPI power Dell SupportAssist OS Recovery. Dell SupportAssist OS Recovery is a standalone tool that is preinstalled in all Dell computers installed with Windows operating system. It consists of tools to diagnose and troubleshoot
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 117
    to create a recovery drive to troubleshoot and fix problems that may occur with Windows. Dell proposes multiple options for recovering Windows operating system on your Dell PC. For more information. see Dell Windows Backup Media and Recovery Options. Wi-Fi power cycle About this task If your
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 118
    4. Wait for 30 seconds. 5. Turn on the wireless router. 6. Turn on the modem. 7. Turn on your computer. 118 Troubleshooting
  • Dell OptiPlex Small Form Factor 7010 | Owners Manual - Page 119
    about your computer through videos, manuals and documents. Your Dell computer is uniquely identified by a Service Tag or Express Service Code. To view relevant support resources for your Dell computer, enter the Service Tag or Express Service Code at www.dell.com/support. For more information on
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
OptiPlex Small Form Factor 7010
Owner's Manual
Regulatory Model: D17S
Regulatory Type: D17S003
March 2023
Rev. A00