Dell PowerEdge M420 Brocade 4424 Blade Server SAN I/O QuickStart Guide
Dell PowerEdge M420 Manual
 |
View all Dell PowerEdge M420 manuals
Add to My Manuals
Save this manual to your list of manuals |
Dell PowerEdge M420 manual content summary:
- Dell PowerEdge M420 | Brocade 4424 Blade Server SAN I/O QuickStart Guide - Page 1
53-1000572-01 November, 2007 Brocade 4424 QuickStart Guide - Dell PowerEdge M420 | Brocade 4424 Blade Server SAN I/O QuickStart Guide - Page 2
, products, or service names are or may be trademarks or service marks of, and are used to identify, products or services of their respective owners. Notice: The source code, please visit http://www.brocade.com/support/oscd. Export of technical data contained in this document may require an export - Dell PowerEdge M420 | Brocade 4424 Blade Server SAN I/O QuickStart Guide - Page 3
This Quick Start guide is intended as an overview to help experienced installers unpack, install, and configure a Brocade 4424 switch quickly. For detailed installation and configuration instructions, see the Brocade 4424 Blade Server SAN I/O Module Hardware Reference Manual. Throughout this - Dell PowerEdge M420 | Brocade 4424 Blade Server SAN I/O QuickStart Guide - Page 4
are required for configuring and connecting the SAN I/O Module for use in a network and fabric: • The SAN I/O Module installed in a Blade Server Enclosure. For instructions, refer to the steps on installing an I/O module in the Hardware Owner's Manual for the Blade Server Enclosure. • If required - Dell PowerEdge M420 | Brocade 4424 Blade Server SAN I/O QuickStart Guide - Page 5
. For instructions, refer to Configuration Guide for your Blade Server Enclosure. 2. Disable any serial communication programs that are running on the workstation. 3. Using a terminal emulator application (such as HyperTerminal on a PC or TERM in a LINUX or UNIX environment), establish a terminal - Dell PowerEdge M420 | Brocade 4424 Blade Server SAN I/O QuickStart Guide - Page 6
in bay B2. Switch-5 for SAN I/O Module installed in bay C1. Switch-6 for SAN I/O module installed in bay C2. 3. At the login prompt, log in to the SAN I/O Module. The default user name is "admin" and the password is "password". 8 of 16 4424 QuickStart Guide Publication Number: 53-1000572-01 - Dell PowerEdge M420 | Brocade 4424 Blade Server SAN I/O QuickStart Guide - Page 7
IP address of the selected SAN I/O module. Refer to your Blade Server Enclosure CLI documentation. Using the CMC GUI to set the IP Management Controller (CMC) to a remote management workstation for any additional configuration. The management workstation must be on the same Ethernet subnet as - Dell PowerEdge M420 | Brocade 4424 Blade Server SAN I/O QuickStart Guide - Page 8
Fabric Switch mode. This affects the configuration process. Using the SAN I/O Module 1. If the SAN I/O Module is not powered on until after it is connected to the fabric n): [no] Arbitrated Loop parameters (yes, y, no, n): [no] System services (yes, y, no, n): [no] Portlog events enable (yes, y, no - Dell PowerEdge M420 | Brocade 4424 Blade Server SAN I/O QuickStart Guide - Page 9
install easily, ensure that it is correctly oriented and that the end caps have been removed. The cables used in trunking groups must meet specific requirements. For a list of these requirements, see the Fabric OS Administrator's Guide 4424 SAN Blade Server I/O Module Hardware Reference Manual. 7. - Dell PowerEdge M420 | Brocade 4424 Blade Server SAN I/O QuickStart Guide - Page 10
to a replacement SAN I/O Module. For specific instructions about how to back up the configuration, see the Fabric OS Administrator's Guide. The switchShow, fabricShow, and configUpload commands are described in detail in the Fabric OS Command Reference Manual. Changing from Fabric Switch mode to - Dell PowerEdge M420 | Brocade 4424 Blade Server SAN I/O QuickStart Guide - Page 11
in Access Gateway mode. See the Access Gateway Administrator's Guide for more detailed configuration information. You can also enter the ag --mapshow the module automatically reboots in Fabric Switch mode. For complete instructions on disabling Access Gateway Mode using the CLI and joining the - Dell PowerEdge M420 | Brocade 4424 Blade Server SAN I/O QuickStart Guide - Page 12
current configuration before Blade Server Enclosure CMC software. Ports on Demand is ready to be unlocked in the SAN I/O Module firmware servers and storage connecting to SAN I/O Module. For new SAN I/O Module installations Guide. For details about the CLI, see the Fabric OS Command Reference Manual. - Dell PowerEdge M420 | Brocade 4424 Blade Server SAN I/O QuickStart Guide - Page 13
IP address of the SAN I/O Module in the address field and press Enter. For more information about using Web Tools, see the Web Tools Administrator's Guide. 4424 QuickStart Guide Publication Number: 53-1000572-01 15 of 16 - Dell PowerEdge M420 | Brocade 4424 Blade Server SAN I/O QuickStart Guide - Page 14
16 of 16 4424 QuickStart Guide Publication Number: 53-1000572-01
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
 |
 |
53-1000572-01
November, 2007
Brocade 4424
QuickStart Guide