Dell PowerEdge Rack Enclosure 4820 Cabling PowerEdge R515
Dell PowerEdge Rack Enclosure 4820 Manual
 |
View all Dell PowerEdge Rack Enclosure 4820 manuals
Add to My Manuals
Save this manual to your list of manuals |
Dell PowerEdge Rack Enclosure 4820 manual content summary:
- Dell PowerEdge Rack Enclosure 4820 | Cabling PowerEdge R515 - Page 1
Cable Routing Procedures for Dell™ PowerEdge™ R515 Systems A Dell™ Technical White Paper By Greg Henderson, Chris Kitten and Jose L. Flores Dell™ │ Datacenter Infrastructure Engineering March 2011 - Dell PowerEdge Rack Enclosure 4820 | Cabling PowerEdge R515 - Page 2
Cable Routing Procedures for Dell™ PowerEdge™ R515 Systems THIS WHITE PAPER IS FOR INFORMATIONAL PURPOSES ONLY, AND MAY CONTAIN TYPOGRAPHICAL ERRORS AND TECHNICAL INACCURACIES. THE CONTENT IS PROVIDED AS IS, WITHOUT EXPRESS OR IMPLIED WARRANTIES OF ANY KIND. © 2011 Dell Inc. All rights reserved. - Dell PowerEdge Rack Enclosure 4820 | Cabling PowerEdge R515 - Page 3
1.5 Left-Side Mounting Instructions...4 1.6 Right-Side Mounting Instructions ...5 Section 2: Cabling a Dell™ PowerEdge™ R515 System Without a CMA 6 2.1 Routing the Cables ...6 2.2 Removing the CMA Brackets for Shallow Racks 7 Section 3: Replacing a Power Supply on a PowerEdge™ R515 System With - Dell PowerEdge Rack Enclosure 4820 | Cabling PowerEdge R515 - Page 4
Practices Guide for Rack Enclosure white paper. Section 1: Cabling a Dell™ PowerEdge™ R515 With a Cable Management Arm (CMA) This section details how to cable a PowerEdge™ R515 system using a CMA. If you are cabling the system without the optional CMA, refer to Section 2. Follow the instructions - Dell PowerEdge Rack Enclosure 4820 | Cabling PowerEdge R515 - Page 5
Procedures for Dell™ PowerEdge™ R515 Systems 1.2 Installing the Inner CMA Attachment Bracket As described in the Rack Installation Instructions, locate route the power cables through the strain reliefs located on the power supply handles as shown in Figure 3. Figure 3: Routing Power Cables Through - Dell PowerEdge Rack Enclosure 4820 | Cabling PowerEdge R515 - Page 6
Cable Routing Procedures for Dell™ PowerEdge™ R515 Systems NOTE: For guidelines on how to route cables within the rack, refer to the Dell Best Practices Guide for Rack Enclosures white paper. 1.5 Left-Side Mounting Instructions 1. Install the CMA on the rear left side of the rails by attaching both - Dell PowerEdge Rack Enclosure 4820 | Cabling PowerEdge R515 - Page 7
Dell™ PowerEdge™ R515 Systems Figure 5: Left-Side Mounted CMA Installation (Preferred) 1.6 Right-Side Mounting Instructions restrict the ability of the CMA to support full extension of the rails without causing position. 6. Extend the system out of the rack to verify that there is sufficient slack in - Dell PowerEdge Rack Enclosure 4820 | Cabling PowerEdge R515 - Page 8
-Side Mounting. Section 2: Cabling a Dell™ PowerEdge™ R515 System Without a CMA NOTE: The CMA on Dell™ PowerEdge™ R515 systems is optional. Without the CMA installed, the system must be powered down and all cables disconnected before it can be removed from the rack. 2.1 Routing the Cables 1. Connect - Dell PowerEdge Rack Enclosure 4820 | Cabling PowerEdge R515 - Page 9
Cable Routing Procedures for Dell™ PowerEdge™ R515 Systems Figure 7: Cable Routing Without a CMA 2.2 Removing the CMA Brackets for Shallow Racks If you are installing the system into a shallow rack (less than 1 meter deep) and you will not be installing a CMA, the outer CMA brackets may be removed - Dell PowerEdge Rack Enclosure 4820 | Cabling PowerEdge R515 - Page 10
as described in the CMA Installation Instructions provided with the CMA kit. If the top power supply must be replaced, this step can be skipped. 2. Swing the CMA to its service position. 3. Disconnect the inner CMA bracket from the rail as shown in Figure 9. 4. While supporting the CMA with one hand - Dell PowerEdge Rack Enclosure 4820 | Cabling PowerEdge R515 - Page 11
for Dell™ PowerEdge™ R515 Systems Figure 10: Replacing the Outer Power Supply Disconnected inner CMA bracket Section 4: Cabling a PowerEdge™ R515 System Installed in Static Rails NOTE: The CMA is compatible with the sliding rails only, not the static rails. 1. Follow the instructions contained
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
 |
 |
Cable Routing Procedures for
Dell™ PowerEdge™ R515 Systems
A Dell
™
Technical White Paper
By Greg Henderson, Chris Kitten and Jose L. Flores
Dell
™
│
Datacenter Infrastructure Engineering
March 2011