Dell PowerEdge UPS 500T JY9T4 Environmental Probe (EMP) User’s Guide
Dell PowerEdge UPS 500T Manual
 |
View all Dell PowerEdge UPS 500T manuals
Add to My Manuals
Save this manual to your list of manuals |
Dell PowerEdge UPS 500T manual content summary:
- Dell PowerEdge UPS 500T | JY9T4 Environmental Probe (EMP) User’s Guide - Page 1
Dell™ Environmental Monitoring Probe User's Guide www.dell.com | www.support.dell.com | www.dellups.com - Dell PowerEdge UPS 500T | JY9T4 Environmental Probe (EMP) User’s Guide - Page 2
- Dell PowerEdge UPS 500T | JY9T4 Environmental Probe (EMP) User’s Guide - Page 3
Dell™ Environmental Monitoring Probe User's Guide www.dell.com | www.support.dell.com | www.dellups.com - Dell PowerEdge UPS 500T | JY9T4 Environmental Probe (EMP) User’s Guide - Page 4
and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this written permission of Dell Inc. is strictly forbidden. Trademarks used in this text: Dell and the Dell logo are trademarks of Dell Inc.; VELCRO is - Dell PowerEdge UPS 500T | JY9T4 Environmental Probe (EMP) User’s Guide - Page 5
Table of Contents Introduction Features 1 Installation Unpacking the EMP 3 Installing the EMP 4 Configuring the EMP Viewing Environment Status 6 Changing Environment Settings 8 Viewing and Saving Environment Log Data 11 Table of Contents i - Dell PowerEdge UPS 500T | JY9T4 Environmental Probe (EMP) User’s Guide - Page 6
ii Table of Contents - Dell PowerEdge UPS 500T | JY9T4 Environmental Probe (EMP) User’s Guide - Page 7
two contact devices through a standard Web browser, providing greater power management control and flexible monitoring. Use the EMP with any Dell UPS equipped with a Dell Network Management Card (firmware v01.10.xxxx or later). NOTE: Download firmware updates for the Network Management Card from www - Dell PowerEdge UPS 500T | JY9T4 Environmental Probe (EMP) User’s Guide - Page 8
• When temperature and humidity values exceed user-selectable limits, the event is logged in the card's Event History log. • Compatible with any Dell Network Management Card (firmware v01.10.xxxx or later). 2 Introduction - Dell PowerEdge UPS 500T | JY9T4 Environmental Probe (EMP) User’s Guide - Page 9
the EMP. Unpacking the EMP Verify the package contents (see Figure 2): • Dell Environmental Monitoring Probe • Ethernet cable • Installation accessories • Installation instructions • User's guide (this document) Figure 2. Dell Environmental Monitoring Probe Package Contents Installation 3 - Dell PowerEdge UPS 500T | JY9T4 Environmental Probe (EMP) User’s Guide - Page 10
Installing the EMP To install the EMP: 1 If you plan to monitor one or two external contact devices, connect external contact closure inputs to the screw terminals on the EMP (see Figure 3 and Table 1). NOTE: Contact closure devices can be normally open or normally closed. Pins 123 4 Figure 3. - Dell PowerEdge UPS 500T | JY9T4 Environmental Probe (EMP) User’s Guide - Page 11
2 Locate the Ethernet cable (supplied). Connect one end of the cable to the RJ-45 port on the EMP, then connect the other end to the Settings port on the Network Management Card (see Figure 4). EMP Network Management Card Figure 4. Connecting the Cable NOTE: If the configuration cable is still - Dell PowerEdge UPS 500T | JY9T4 Environmental Probe (EMP) User’s Guide - Page 12
Configuring the EMP This section explains how to: • Display temperature, humidity, and status of two contact devices through a standard Web browser • Change environment settings • View environment log data and save the data in a CSV format file Viewing Environment Status 1 Open your Web browser and - Dell PowerEdge UPS 500T | JY9T4 Environmental Probe (EMP) User’s Guide - Page 13
Temperature and humidity measurements are displayed in a graduated bar (see Figure 6). The red zones to the left and right of the bar represent the low and high thresholds. If notification is turned on, an alarm is generated when the measured value enters one of these zones. The cursor indicates the - Dell PowerEdge UPS 500T | JY9T4 Environmental Probe (EMP) User’s Guide - Page 14
Changing Environment Settings On the Environment Settings page you can: • Set the temperature and humidity thresholds that trigger a notification (and a graceful shutdown of the protected systems). • Configure and enable both contacts, as well as set upper and lower ranges of temperature and - Dell PowerEdge UPS 500T | JY9T4 Environmental Probe (EMP) User’s Guide - Page 15
(humidity) Low threshold (humidity) Hysteresis (humidity) Input #1 and Input #2 when closed and when open Description The name given to the EMP. Dell recommends using a name that identifies the location of the EMP. Choice of the temperature unit (°C or °F) from the list. If the temperature exceeds - Dell PowerEdge UPS 500T | JY9T4 Environmental Probe (EMP) User’s Guide - Page 16
mail. The Environment Log check box must be selected on the Email Notification page. NOTE: Refer to the Network Management Card user's guide for more information on e-mail notification and for a list of alarm messages. Selection triggers a system shutdown for each selected notification. This option - Dell PowerEdge UPS 500T | JY9T4 Environmental Probe (EMP) User’s Guide - Page 17
measurements are recorded at an interval defined on the environment log interval on the System Settings page (refer to the Network Management Card user's guide for information on system settings). By default, this period is 300 seconds. Each measurement is dated and stored in the log of the UPS - Dell PowerEdge UPS 500T | JY9T4 Environmental Probe (EMP) User’s Guide - Page 18
12 Configuring the EMP - Dell PowerEdge UPS 500T | JY9T4 Environmental Probe (EMP) User’s Guide - Page 19
- Dell PowerEdge UPS 500T | JY9T4 Environmental Probe (EMP) User’s Guide - Page 20
*123456789 1* P-164000076 1
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
 |
 |
www.dell.com | www.support.dell.com | www.dellups.com
Dell
™
Environmental Monitoring Probe
User’s Guide