Dell PowerSwitch S4048T-ON OS10 Enterprise Edition User Guide Release 10.4.0ER
Dell PowerSwitch S4048T-ON Manual
View all Dell PowerSwitch S4048T-ON manuals
Add to My Manuals
Save this manual to your list of manuals |
Dell PowerSwitch S4048T-ON manual content summary:
- Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 1
OS10 Enterprise Edition User Guide Release 10.4.0E(R2) - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 2
and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. Copyright © 2018 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries. Other trademarks may - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 3
Contents 1 Getting Started...20 Download OS10 image and license...21 Installation...22 Automatic installation...23 Manual installation...23 Log into OS10...24 Install OS10 license...24 Remote access...25 Configure Management IP address...26 Management Route Configuration...26 Configure user name - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 4
delete...49 description (alias)...50 dir...50 discard...51 do...51 feature config-os9-style...52 exit...52 license...53 line (alias)...53 lock...54 management route...54 move...55 no...55 reload...56 show alias...56 show boot...57 show candidate-configuration...58 show environment...60 show - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 5
Minimum links...78 Assign IP address...79 Remove or disable port-channel...79 Load balance traffic...79 Change hash algorithm...80 Configure interface ranges...80 Switch-port profiles...81 S4148-ON Series port profiles...82 S4148U-ON port profiles...82 Unified port groups...84 Configure breakout - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 6
show port-group...110 show switch-port-profile...111 show unit-provision...111 show vlan...112 shutdown...112 speed (Fibre Channel)...112 speed (Management)...113 switch-port-profile...114 switchport access vlan...116 switchport mode...116 switchport trunk allowed vlan...117 unit-provision...117 3 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 7
show fcoe sessions...137 show fcoe statistics...137 show fcoe system...138 show fcoe vlan...138 show npg devices...138 show running-config vfabric...139 show vfabric...140 vfabric...141 vfabric (interface)...141 vlan...141 zone default-zone permit...142 zoneset activate...142 4 Layer 2...143 802.1X - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 8
Table...191 MAC Commands...192 Multiple spanning-tree protocol...194 Configure MST protocol...195 Create instances...195 Root selection...197 Non-Dell hardware...197 Region name or revision...197 Modify parameters...198 Interface parameters...199 Forward traffic...199 Spanning-tree extensions...200 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 9
Weight and local preference...260 Multiexit discriminators...261 Origin...261 AS path and next-hop...262 Best path selection...262 More path support...263 Advertise cost...263 4-Byte AS numbers...264 AS number migration...264 Configure border gateway protocol...265 Enable BGP...265 Configure Dual - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 10
Neighbor soft-reconfiguration...281 BGP commands...282 Equal cost multi-path...307 Load balancing...307 ECMP commands...307 IPv4 routing...310 Assign interface IP address...310 Configure static routing...311 Address resolution protocol...312 IPv4 routing commands...312 IPv6 routing...316 Enable or - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 11
431 Dynamic host configuration protocol...431 Packet format and options...431 Configure Server...432 Automatic address allocation...433 Hostname resolution...434 Manual binding entries...435 View DHCP Information...436 System domain name and list...436 DHCP commands...437 DNS commands...442 Network - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 12
User session management...454 User session management commands...454 Telnet server...455 Telnet commands...456 Security...456 User re-authentication...457 Password strength...457 Role-based access control...458 Assign user role...458 RADIUS authentication...459 TACACS+ authentication...459 SSH - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 13
Enable flow-based monitoring...492 ACL commands...493 clear ip access-list counters...493 clear ipv6 access-list counters...493 clear mac access-list counters...494 deny...494 deny (IPv6)...495 deny (MAC)...495 deny icmp...496 deny icmp (IPv6)...497 deny ip...497 deny ipv6...498 deny tcp...498 deny - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 14
permit tcp...516 permit tcp (IPv6)...517 permit udp...517 permit udp (IPv6)...518 remark...519 seq deny...519 seq deny (IPv6)...520 seq deny (MAC)...521 seq deny icmp...522 seq deny icmp (IPv6)...522 seq deny ip...523 seq deny ipv6...524 seq deny tcp...524 seq deny tcp (IPv6)...525 seq deny udp... - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 15
next-hop...550 set origin...550 set tag...550 set weight...551 show route-map...551 9 Quality of service...552 Configure quality of service...552 Ingress traffic classification...554 Data traffic classification...554 Control-plane policing...558 Egress traffic classification...561 Policing traffic - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 16
random-detect (interface)...582 random-detect (queue)...583 random-detect color...583 random-detect ecn...584 random-detect pool...584 random-detect weight...584 service-policy...585 set cos...585 set dscp...586 set qos-group...586 shape...586 show class-map...587 show control-plane info...587 show - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 17
show vlt vlt-port-detail...619 vlt-domain...619 vlt-port-channel...619 vlt-mac...620 vrrp mode active-active...620 11 Converged data center services...621 Priority flow control...621 PFC configuration notes...622 Configure PFC...624 Contents 17 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 18
collector...659 sflow enable...660 sflow max-header-size...660 sflow polling-interval...660 sflow sample-rate...661 show sflow...661 13 Troubleshoot OS10...663 Diagnostic tools...663 Boot partition and image...664 Monitor processes...664 LED settings...665 Packet analysis...665 Port adapters and - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 19
Frequently asked questions...706 Installation...706 Hardware...706 Configuration...707 Security...707 Layer 2...707 Layer 3...707 System management...708 Access control lists...708 Quality of service...708 Monitoring...709 14 Support resources...710 Contents 19 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 20
EMC device • OS10 software image stored on an HTTP server or universal serial bus (USB) media • Familiarity with any Linux release Supported Dell EMC platforms • S3048-ON • S4048-ON, S4048T-ON • S4128F-ON, S4128T-ON • S4148F-ON, S4148T-ON • S4148U-ON, S4148FE-ON • S6010-ON, Z9100-ON • S4248FB-ON - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 21
period. See the Quick Start Guide shipped with your device and My Account License.zip file and follow the instructions in Install license to install the (APOS) order for a Dell EMC ONIE-enabled device that service tag of the switch to extend the entitled download period to be the same time as the support - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 22
and downloads and installs an image automatically. • Manual installation - Manually configure your network information if a DHCP server is port, see the Getting Started Guide shipped with your device or the platform-specific Installation Guide at www.dell.com/support. Install OS10 If an operating - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 23
an automatic or manual OS10 installation, if an error condition occurs that results in an unsuccessful installation, perform Uninstall OS first to clear the partitions if there is an existing OS on the device. If the problem persists, contact Dell EMC Technical Support. Automatic installation You - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 24
the License.zip file from DDL as described in Download OS10 image and license. 2 Open the zip file and locate the license file in the Dell folder. Copy the license file to a local or remote workstation. 3 Install the license file from the workstation in EXEC mode. license install {ftp: | http - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 25
Name : S4048-ON PPID : CN0M68YC2829855M0133 Service Tag : CFNNX42 License Details Software : OS10-Enterprise Version : 10.3.0E License Type : PERPETUAL License Duration: Unlimited License Status : Active License location: /mnt/license/CFNNX42.lic Troubleshoot license installation failure An error - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 26
Remote access OS10 CLI 1 Open an SSH session using the IP address of the device. You can also use PuTTY or a similar tool to access the device remotely. ssh admin@ip-address password: admin 2 Enter admin for both the default user name and password to log into OS10. You are automatically placed in - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 27
passwords entered in MD-5, SHA-256, and SHA-512 format are supported. To increase the required password strength, use the password-attributes Enterprise Edition image to download, then click Download. 5 Read the Dell End User License Agreement, then scroll to the end of the agreement and click - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 28
switch with an installed OS10 license. See Install OS10 license for complete instructions. CLI Basics The OS10 command-line interface (CLI) is the software two top-level modes: • EXEC mode - Used to monitor, troubleshoot, check status, and network connectivity. • CONFIGURATION mode - Used to - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 29
inconsistent configuration changes may be applied to the running configuration. Dell EMC recommends that you only make configuration changes on a single configure Layer 2 and Layer 3 protocols, and IPv4 and IPv6 services specific to an interface: • Physical interfaces include the Management interface - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 30
filesystem No commands under exec mode ping -h shows help ping6 -h shows help Reboot Dell EMC Networking Operating System Show running system information Activate transaction based configuration Support Assist related activity System command Set terminal settings traceroute --help shows help Unlock - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 31
login-statistics mac management monitor no ntp policy-map qos-map radius-server parameters route-map router sflow snmp-server spanning-tree support-assist system telnet track trust username vlt-domain vrrp wred Configure AAA Set alias for a command Configure class map Configure clock parameters - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 32
Show spanning tree information Contents of startup configuration Show storm control configuration support-assist Shows information about the support assist module system Show system status information tech-support terminal trace Collection of show commands Show terminal configurations for this - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 33
6 Thu Apr 20 19:47:16 UTC 2017 terminal length 0 7 Thu Apr 20 19:47:18 UTC 2017 terminal datadump 8 Thu Apr 20 19:47:20 UTC 2017 %abc 9 Thu Apr 20 19:47:22 UTC 2017 switchshow 10 Thu Apr 20 19:47:24 UTC 2017 cmsh 11 Thu Apr 20 19:47:26 UTC 2017 show version 12 Thu Apr 20 19:47:28 UTC 2017 cmsh 13 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 34
-list interface lacp lldp logging monitor ospf ospfv3 policy-map prefix-list qos-map radius-server route-map sflow snmp spanning-tree support-assist system-qos trust-map users vlt Current candidate aaa configuration Current candidate access-list configuration Current candidate as-path configuration - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 35
$jfxzVqGhkxX3smxJSH9DDz7/3OJc6m5wjF8nnLD7/VKx8SloIhp4NoGZs0I/ UNwh8WVuxwfd9q4pWIgNs5BKH. role sysadmin aaa authentication local snmp-server contact http://www.dell.com/support ! interface range ethernet 1/1/1-1/1/32 switchport access vlan 1 no shutdown ! interface vlan 1 no shutdown ! interface - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 36
$jfxzVqGhkxX3smxJSH9DDz7/3OJc6m5wjF8nnLD7/VKx8SloIhp4NoGZs0I/ UNwh8WVuxwfd9q4pWIgNs5BKH. role sysadmin aaa authentication local snmp-server contact http://www.dell.com/support ! interface range ethernet 1/1/1-1/1/32 switchport access vlan 1 no shutdown ! interface vlan 1 no shutdown ! interface - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 37
command, the current session switches back to the default behavior of committing all configuration changes automatically. Save configuration changes manually OS10# start transaction OS10# configure terminal OS10(config)# OS10(config)# interface ethernet 1/1/1 OS10(config-if-eth1/1/1)# no shutdown - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 38
file from server OS10# copy scp://admin:admin@hostip/backup-9-28.xml config://startup.xml OS10# reload Reload system image Reboot the system manually using the reload command in EXEC mode. You are prompted to confirm the operation. OS10# reload System configuration has been modified. Save? [yes - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 39
The alias command allows you to create shortcuts for commonly used or long commands, and execute long commands along with their parameters. The alias supports the following modes: • Persistent mode - The alias is persistent and can be used in other sessions as well. The aliases created in the - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 40
goint Multi-line alias You can create multi-line alias where you can save a series of multiple commands in an alias. Multi-line alias is supported only in the Configuration mode. 40 Getting Started - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 41
You cannot use the exiting CLI keywords as alias names. The alias name is case-sensitive and can have a maximum of 16 characters. • Create an alias in the CONFIGURATION mode. The switch enters the ALIAS mode. alias alias-name • Enter the commands to be executed prefixed by the line n command in the - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 42
line 2 "no shutdown" line 3 "show configuration" line 4 exit View alias information OS10# show alias Name ---mTest Type ---Config Number of config aliases : 1 Number of local aliases : 0 View alias information brief (displays the first 10 characters of the alias value) OS10# show alias brief - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 43
:44-0800 System Type: S4048-ON Architecture: x86_64 Up Time: 1 week 4 days 08:07:44 User admin logged out at session 10 admin@OS10:/opt/dell/os10/bin$ • Use the -B option along with a batch file to execute a series of commands. configure terminal router bgp 100 neighbor 100.1.1.1 remote-as 104 no - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 44
execute commands remotely using an SSH session. This is supported only for show commands. • Enter the show command along with SSH. $ ssh admin@ip-address show-command $ ssh [email protected] "show version" [email protected]'s password: Dell EMC Networking OS10 Enterprise Copyright (c) 1999-2017 by - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 45
alias Creates a command alias. Syntax alias alias-name alias-value Parameters Default Command Mode • alias-name - Enter the name of the alias (up to 20 characters). • alias-value - Enter the command to be executed within double quotes (1 to 9 or *). Enter the $ followed by either numbers - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 46
2 "no shutdown" OS10(config-alias-mTest)# line 3 "show configuration" Supported Releases 10.4.0E(R1) or later batch Executes a series of commands in . Example OS10# batch b.cmd OS10# Feb 15 19:26:1: %Dell EMC (OS10) %Node.1-Unit.1:PRI:OS10 %lognotice:IP_ADDRESS_ADD: IP Address add - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 47
Use the show boot command to view the configured next boot image. This command is applied immediately. OS10# boot system standby Supported Releases 10.2.0E or later commit Commits changes in the candidate configuration to the running configuration. Syntax commit Parameters None Default Not - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 48
SCP server. • sftp://userid:passwd@hostip/filepath - (Optional) Copy from a remote SFTP server. • supportbundle://filepath - (Optional) Copy from the support-bundle directory. • tftp://hostip/filepath - (Optional) Copy from a remote TFTP server. • usb:filepath - (Optional) Copy from an USB file - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 49
2017-02-15T21:19:54Z 54525 config.xml ... Name Example (replace startup configuration) OS10# home://config.xml config://startup.xml Supported Releases 10.2.0E or later default (alias) Configures default values for input parameters in multi-line alias. Syntax default n value Parameters - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 50
version of this command removes the description. Example OS10(config)# alias mTest OS10(config-alias-mTest)# description "This alias configures interfaces" Supported Releases 10.4.0E(R1) or later dir Displays files stored in available directories. Syntax dir [config | coredump | home | image - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 51
) OS10# dir config Directory contents for folder: config Date (modified) Size (bytes) Name 2017-04-26T15:23:46Z 26704 startup.xml Supported Releases 10.2.0E or later discard Discards any changes made to the candidate configuration file. Syntax discard Parameters None Default Not - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 52
next session, you can configure the commands in OS9 format. The current release supports VLAN tagging and Port channel grouping commands. This feature does not have any impact breakout 1/1/28 map 10g-4x feature config-os9-style Supported Releases 10.3.0E or later exit Returns to the next - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 53
is installed in the /mnt/license directory. OS10# license install scp://user:userpwd/10.1.1.10/CFNNX42-NOSEnterpriseLicense.lic License installation success. Supported Releases 10.3.0E or later line (alias) Configures the commands to be executed in a multi-line alias. Syntax line nn command - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 54
Command Mode EXEC Usage Information The lock command fails if there are uncommitted changes in the candidate configuration. Example OS10# lock Supported Releases 10.2.0E or later management route Configures an IPv4/IPv6 static route used by the Management port. Repeat the command to - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 55
-backup.xml Example (dir) OS10# dir config Directory contents for folder: config Date (modified) Size (bytes) Name 2017-04-26T15:23:46Z 26704 startup.xml Supported Releases 10.2.0E or later no Disables or deletes commands in EXEC mode. Syntax no [alias | debug - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 56
this command, as it reloads the OS10 image and reboots the device. Example OS10# reload Proceed to reboot the system? [confirm yes/no]:y Supported Releases 10.2.0E or later show alias Displays configured alias commands available in both persistent and non-persistent modes. Syntax show alias - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 57
Config goint Config mTest Config shconfig showint shver Local Local Local Number of config aliases : 3 Number of local aliases : 3 Supported Releases 10.3.0E or later "show versi..." Value ----"vlt-domain $1" "interface ethernet $1" line 1 "interface $1 $2" line 2 "no shutdown" line 3 "show - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 58
| lldp | logging | monitor | ospf | ospfv3 | policy-map | prefix-list | qos-map | radius-server | route-map | sflow | snmp | spanningtree | support-assist | system-qos | trust-map | users | vlt] Parameters • aaa - (Optional) Current candidate AAA configuration. • access-list - (Optional) Current - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 59
admin password $6$q9QBeYjZ$jfxzVqGhkxX3smxJSH9DDz7/3OJc6m5wjF8nnLD7/ VKx8SloIhp4NoGZs0I/UNwh8WVuxwfd9q4pWIgNs5BKH. aaa authentication local snmp-server contact http://www.dell.com/support snmp-server location "United States" logging monitor disable ip route 0.0.0.0/0 10.11.58.1 ! interface ethernet1 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 60
Inlet Ambient-3 temp sensor 26 1 6 Switch board 2 temp sensor 31 1 7 Switch board 3 temp sensor 41 1 8 NPU temp sensor 43 Supported Releases 10.2.0E or later show inventory Displays system inventory information. Syntax Parameters Default Command Mode Usage Information Example show - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 61
or IPv6 management route. OS10# show ip management-route Destination Gateway State Source 192.168.10.0/24 managementethernet Connected Connected Supported Releases 10.2.2E or later show ipv6 management-route Displays the IPv6 routes used to access the management port. Syntax show - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 62
to verify the current license for running OS10, its duration, and the service tag of the switch to which it is assigned. Example OS10# show : 45 day(s) left License location: /mnt/license/.lic Supported Releases 10.3.0E or later show running-configuration Displays the configuration - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 63
admin password $6$q9QBeYjZ$jfxzVqGhkxX3smxJSH9DDz7/3OJc6m5wjF8nnLD7/ VKx8SloIhp4NoGZs0I/UNwh8WVuxwfd9q4pWIgNs5BKH. aaa authentication local snmp-server contact http://www.dell.com/support snmp-server location "United States" logging monitor disable ip route 0.0.0.0/0 10.11.58.1 ! interface ethernet1 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 64
admin password $6$q9QBeYjZ$jfxzVqGhkxX3smxJSH9DDz7/3OJc6m5wjF8nnLD7/ VKx8SloIhp4NoGZs0I/UNwh8WVuxwfd9q4pWIgNs5BKH. aaa authentication local snmp-server contact http://www.dell.com/support snmp-server location "United States" logging monitor disable ip route 0.0.0.0/0 10.11.58.1 ! interface range - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 65
admin password $6$q9QBeYjZ$jfxzVqGhkxX3smxJSH9DDz7/3OJc6m5wjF8nnLD7/ VKx8SloIhp4NoGZs0I/UNwh8WVuxwfd9q4pWIgNs5BKH. aaa authentication local snmp-server contact http://www.dell.com/support snmp-server location "United States" ip route 0.0.0.0/0 10.11.58.1 ! interface range ethernet 1/1/1-1/1/32 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 66
Default Command Mode Usage Information Example Not configured EXEC None OS10#show system Node Id MAC Number of MACs Up Time : 1 : 34:17:18:19:20:21 : 0 : 1 week 4 days 08:08:17 -- Unit 1 -Status System Identifier Down Reason System Location LED Required Type Current Type Hardware Revision - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 67
) Status 1 up REVERSE 1 13063 up 2 13020 up 2 up REVERSE 1 12956 up 2 12977 up 3 up NORMAL 1 12956 up 2 13063 up Supported Releases 10.2.0E or later show version Displays software version information. Syntax show version Parameters None Default Not configured Command - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 68
the Linux command to execute. Not configured EXEC None OS10# system bash admin@OS10:~$ pwd /config/home/admin admin@OS10:~$ exit OS10# Supported Releases 10.2.0E or later system identifier Sets a non-default unit ID in a non-stacking configuration. Syntax system identifier system-identifier-ID - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 69
Command Mode Usage Information Example 24 terminal lines EXEC Enter zero (0) for the terminal to display without pausing. OS10# terminal monitor Supported Releases 10.2.0E or later traceroute Displays the routes that packets take to travel to an IP address. Syntax Parameters traceroute [vrf - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 70
(Optional) For IPv4, enter the Type of Service (TOS) and Precedence values to use. 16 Information Example Not configured EXEC None OS10# traceroute www.dell.com traceroute to www.dell.com (23.73.112.54), 30 hops max 2.622 ms 2.649 ms 2.964 ms Supported Releases 10.2.0E or later unlock Unlocks a - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 71
to a local configuration file other than the startup configuration. Use the copy command to save running configuration changes to a local file. Example OS10# write memory Supported Releases 10.2.0E or later Getting Started 71 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 72
), port-channels, and virtual local area networks (VLANs) in Layer 2 (L2) or Layer 3 (L3) modes. Table 1. Interface types Interface type Supported Ethernet (PHY) L2, L3 Management N/A Loopback L3 Port-channel L2, L3 VLAN L2, L3 Ethernet interfaces Default mode unset N/A L3 unset L3 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 73
trunk interface carries only untagged traffic on the Access VLAN. You must manually configure other VLANs for tagged traffic. 1 Select one of the two before assigning an IP Fibre Channel interfaces OS10 unified port groups support Fibre Channel (FC) interfaces. A unified port group operates in - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 74
Figure 1. S4148U-ON port groups On a S4148U-ON, the activated FC interfaces depend on the currently configured port profile. For more information, see S4148U-ON port profiles. To enable a fibre channel interface: 1 Configure a unified port group in CONFIGURATION mode. Enter 1/1 for node/slot. The - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 75
VLAN interfaces VLANs are logical interfaces and are, by default, in L2 mode. Physical interfaces and port-channels can be members of VLANs. OS10 supports inter-VLAN routing. You can add IP addresses to VLANs and use them in routing protocols in the same manner that physical interfaces are used - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 76
Q Ports A Eth1/1/1-1/1/25,1/1/29,1/1/31-1/1/54 OS10(config)# interface vlan 10 Sep 19 17:28:10 OS10 dn_ifm[932]: Node.1-Unit.1:PRI:notice [os10:notify], %Dell EMC (OS10) %IFM_ASTATE_UP: Interface admin state up :vlan10 OS10(conf-if-vl-10)# exit OS10(config)# default vlan-id 10 Sep 19 17:28:15 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 77
address is 120.120.120.120/24 Mode of IPv4 Address Assignment : MANUAL MTU 1532 bytes Flowcontrol rx false tx false ARP type: ARPA, ARP A port-channel must contain interfaces of the same interface type and speed. OS10 supports a maximum of 128 port-channels, with up to thirty-two ports per channel. - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 78
configuration settings - only the description and shutdown or no shutdowncommands are supported. You cannot add an IP address or a static MAC address A static port-channel (LAG) contains member interfaces that you manually assign using the channel-group command. OS10(config)# interface port-channel - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 79
Configure minimum operationally up links OS10(config)# interface po 1 OS10(conf-if-po-1)# minimum-links 5 Assign IP address Assign an IP address to a port-channel and use port-channels in L3 routing protocols. • Configure an IP address and mask for the interface in INTERFACE mode. Use the secondary - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 80
- ipv6-selection [destination-ip | source-ip | protocol | vlan-id | l4-destination-port | l4- source-port] - Uses the destination IPv6 address, source IPv6 address, protocol, VLAN ID, Layer 4 destination IPv6 address, or Layer 4 source IPv6 address in the hash calculation. - mac-selection [ - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 81
Switch-port profiles A port profile determines the enabled front-panel ports and supported breakout modes on Ethernet and unified ports. Change the port profile on Forwarding Table (UFT) mode • ECMP maximum paths You must manually reconfigure other settings on a switch after you apply a new port - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 82
a QSFP28 port. NOTE: For S4148U-ON port profiles with both unified and Ethernet ports, see S4148U-ON port profiles. An S4148U-ON unified port supports Fibre Channel and Ethernet modes. For example, profile-1 enables 10G speed on forty-eight ports (1-24 and 31-54), and 4x10G breakouts on QSFP28 ports - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 83
-54: • 10GE mode is an SFP+ 10GE port or a 4x10G breakout of a QSFP+ port. • 40GE mode is a QSFP+ port. For example, all S4148U-ON activate support 10G speed on unified ports 1-24 and Ethernet ports 31-54, but only profile-1 and profile-2 activate QSFP+ ports 27-28 in 40GE mode with - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 84
interfaces on a QSFP+ Ethernet port, use the interface breakout command in global Configuration mode. 1GE mode: Only SFP+ ports support 1GE; QSFP+ and QSFP28 ports 25 to 30 do not support 1GE. To view the ports that belong to each port group, use the show port-group command. Unified port groups In - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 85
interface ethernet 1/1/25:1 OS10(conf-if-fc-1/1/25:1)# show configuration ! interface ethernet1/1/25:1 no shutdown Configure breakout mode Using a supported breakout cable, you can split a 40GE QSFP+ or 100GE QSFP28 Ethernet port into separate breakout interfaces. All breakout interfaces have the - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 86
RJ-45 ports and ports that are members of a port group do not support breakout auto-configuration. Breakout auto-configuration is disabled by default. Enable breakout auto-configuration OS10(config)# feature auto-breakout Display breakout auto-configuration Before you - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 87
01:06:28 OS10 dn_l3_core_services[968]: Node.1-Unit.1:PRI:notice [os10:trap], %Dell EMC (OS10) %IP_ADDRESS_DEL: IP Address delete is successful. IP 2.2.2.2/24 deleted successfully (FEC) enhances data reliability. FEC modes supported in OS10: • CL74-FC - Supports 25G and 50G Interfaces 87 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 88
support FEC on 10G and 40G. Configure FEC OS10(config)# interface ethernet 1/1/41 OS10(conf-if-eth1/1/41)# fec CL91-RS View FEC configuration OS10# show interface ethernet 1/1/41 Ethernet 1/1/41 is up, line protocol is up Hardware is Dell by shutting down certain services. EEE transitions into and - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 89
, or following Ethernet cable reconnection. During the link establishment process, both link partners indicate their EEE capabilities. If EEE is supported by both link partners for the negotiated PHY type, EEE functions independently in either direction. Changing the EEE configuration resets the - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 90
EXEC Usage Information Use this command to clear all EEE counters. Example OS10# clear counters interface eee Clear all eee counters [confirm yes/no]:yes Supported Releases 10.3.0E or later 90 Interfaces - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 91
48 eee Clear eee counters on ethernet1/1/48 [confirm yes/no]:yes Supported Releases 10.3.0E or later eee Enables or disables energy-efficient Ethernet EEE) eee None Enabled on Base-T devices and disabled on S3048-ON and S4048T-ON. Interface To disable EEE, use the no version of this command. OS10 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 92
information. Not configured EXEC OS10# show interface ethernet 1/1/48 eee Port EEE Status Speed Duplex Eth 1/1/48 on up 1000M Supported Releases 10.3.0E or later show interface ethernet eee statistics Displays EEE statistics for a specified interface. Syntax show interface ethernet - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 93
48 EEE : on TxIdleTime(us) : 2560 TxWakeTime(us) : 5 Last Clearing : 18:45:53 TxEventCount : 0 TxDuration(us) : 0 RxEventCount : 0 RxDuration(us) : 0 Supported Releases 10.3.0E or later View interface configuration To view basic interface information, use the show interface, show running - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 94
Output statistics: 0 packets, 0 octets 0 64-byte pkts, 0 over 64-byte pkts, 0 over 127-byte pkts 0 over 255-byte pkts, 0 over 511-byte pkts, 0 over 1023-byte pkts 0 Multicasts, 0 Broadcasts, 0 Unicasts 0 throttles, 0 discarded, 0 Collisions, 0 wred drops Rate Info(interval 30 seconds): Input 0 Mbits - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 95
up down Ethernet 1/1/31 unassigned NO unset up down Ethernet 1/1/32 unassigned NO unset up down Management 1/1/1 10.16.153.226/24 YES manual up up Vlan 1 unassigned NO unset up down Vlan 10 unassigned NO unset up down Vlan 20 unassigned NO unset up down Vlan 30 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 96
the interface from the port-channel group. OS10(config)# interface ethernet 1/1/2:1 OS10(conf-if-eth1/1/2:1)# channel-group 20 mode active Supported Releases 10.3.0E or later default interface Resets an Ethernet or Fibre Channel interface to its default settings. Syntax Parameters default - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 97
and port-channel configurations on a physical interface. You must manually remove configured links to the interface from other software features; 00:48 OS10 dn_l3_core_services[590]: Node.1-Unit.1:PRI:notice [os10:trap], %Dell EMC (OS10) %log-notice:IP_ADDRESS_DEL: IP Address delete is successful. IP - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 98
Address delete is successful. IP 192.21.43.1/31 deleted successfully Mar 5 22:21:12 OS10 dn_l3_core_services[590]: Node.1-Unit.1:PRI:notice [os10:trap], %Dell EMC (OS10) %log-notice:IP_ADDRESS_DEL: IP Address delete is successful. IP 2000:21:43::21:43:1/127 deleted successfully Mar 5 22:21:12 OS10 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 99
access vlan 10 ! interface ethernet1/1/3 no shutdown switchport access vlan 10 ! interface ethernet1/1/4 no shutdown switchport access vlan 10 Supported Releases 10.4.0E(R1) or later description (Interface) Configures a textual description of an interface. Syntax description string Interfaces - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 100
. The no version of this command removes the duplex mode configuration from the management port. OS10(conf-if-ma-1/1/1)# duplex auto Supported Releases 10.3.0E or later feature auto-breakout Enables front-panel Ethernet ports to automatically detect SFP media and autoconfigure breakout interfaces - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 101
After you enter the feature auto-breakout command and plug a supported breakout cable in a QSFP+ or QSFP28 port, the port autoconfigures breakout interfaces for media type and speed. Use the interface breakout command to manually configure breakout interfaces. The media type plugged into a port is - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 102
mode {Eth | FC} command in the Port-Group configuration mode. Example OS10(config)# interface breakout 1/1/41 map 10g-4x Supported Releases 10.2.2E or later interface ethernet Configures a physical Ethernet interface. Syntax Parameters Default Command Mode Usage Information Example interface - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 103
port. To assign an IP address to the Management port, use the ip address command. OS10(config)# interface mgmt 1/1/1 OS10(conf-if-ma-1/1/1)# Supported Releases 10.2.0E or later interface null Configures a null interface on the switch. Syntax interface null number Parameters number - Enter the - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 104
interface vlan vlan-id vlan-id - Enter the VLAN ID number (1 to 4093). VLAN 1 CONFIGURATION FTP, TFTP, MAC ACLs, and SNMP operations are not supported - IP ACLs are supported on VLANs only. The no version of this command deletes the interface. OS10(config)# interface vlan 10 OS10(conf-if-vl-10 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 105
, subports 1 and 3. - 32g-1x - Split a port group into one 32GFC interface, subport 1. - 16g-4x - Split a port group into four 16GFC interfaces; supports 4x32GFC oversubscription. - 16g-2x - Split a port group into two 16GFC interfaces using ports 1 and 3. - 8g-4x - Split a port group into four 8GFC - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 106
Eth 10g-4x Example: Reset mode OS10(conf-pg-1/1/2)# mode FC 16g-2x OS10(conf-pg-1/1/2)# no mode OS10(conf-pg-1/1/2)# mode Eth 10g-4x Supported Releases 10.3.1E or later mtu Sets the link maximum transmission unit (MTU) frame size for an Ethernet L2 or L3 interface. Syntax Parameters Default - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 107
enter the show port-group command. OS10(config)# port-group 1/1/8 OS10(conf-pg-1/1/8)# Supported releases 10.3.1E or later show discovered-expanders NOTE: This command will be supported in future releases. Syntax show discovered-expanders show interface Displays interface information. Syntax - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 108
from other command modes. OS10# show interface Ethernet 1/1/2 is up, line protocol is up Hardware is Dell EMC Eth, address is 00:0c:29:54:c8:57 Current address is 00:0c:29:54:c8:57 L2 up 20:34:32 Eth 1/1/20 (Up) Eth 1/1/21 (Up) Eth 1/1/22 (Up) Supported Releases 10.2.0E or later 108 Interfaces - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 109
media System Inventory Media Node/Slot/Port Category Media Serial Dell EMC Number Qualified 1/1/1 Not Present 1/1/2 SFP-PLUS SFPPLUS true 1/1/18 SFP-PLUS SFPPLUS 10GBASE SR AQM146U true ... Supported Releases 10.2.0E or later show link-bundle-utilization Displays - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 110
-Channel Type Protocol Member Ports 22 port-channel22 (U) Eth STATIC 1/1/10(P) 1/1/11(P) 1/1/14(P) 1/1/16(P) 1/1/19(P) 23 port-channel23 (D) Eth STATIC Supported Releases 10.2.0E or later show port-group Displays the current port-group configuration on a switch. Syntax Parameters Default Command - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 111
20 1/1/6 FC 16g-2x 21 22 23 24 1/1/7 Eth 100g-1x 25 1/1/8 Eth 40g-1x 26 1/1/9 Eth 100g-1x 29 1/1/10 Eth 40g-1x 30 Supported Releases 10.3.1E or later show switch-port-profile Displays the current and default port profile on a switch. Syntax Parameters show switch-port-profile node - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 112
on an interface that is a member of a port-channel. Example OS10(config)# interface ethernet 1/1/7 OS10(conf-if-eth1/1/7)# no shutdown Supported Releases 10.2.0E or later speed (Fibre Channel) Configures the transmission speed of a Fibre Channel interface. Syntax Parameters speed {8 | 16 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 113
only on the Management and Fibre Channel interfaces. This command is not supported on Ethernet interfaces. • When you manually configure the management port speed, match the speed of the remote device. Dell EMC highly recommends using auto-negotiation for the management port. • The no version - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 114
31-54) and QSFP28 100G ports (25-26 and 29-30) are enabled. QSFP28 ports support 100GE and 4x10G, 4x25G, and 2x50G breakouts. - profile-2 - SFP+ 10G ports (1-24 40G mode (25-26 and 29-30) are enabled. QSFP+ and QSFP28 ports support 40GE and 4x10G breakouts. - profile-3 - SFP+ 10G ports (5-24 and 31- - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 115
SFP+ unified ports operate in Ethernet 10GE mode by default. SFP+ unified port groups support 4x8GFC and 2x16GFC breakouts (ports 1 and 3) in FC mode. ◦ QSFP28 unified ports Forwarding Table (UFT) mode - ECMP maximum paths You must manually reconfigure other settings on a switch after you apply a - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 116
switchport mode access OS10(conf-if-eth1/1/3)# switchport access vlan 100 Supported Releases 10.2.0E or later switchport mode Places an interface in L2 configures an interface to transmit tagged VLAN traffic. You must manually configure VLAN membership for a trunk port with the switchport trunk - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 117
id-list - Enter the VLAN numbers of the tagged traffic that the L2 trunk port can carry. Commaseparated and hyphenated VLAN number ranges are supported. Default None Command Mode INTERFACE Usage Information Use the no version of this command to remove the configuration. Example OS10(conf-if-ma - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 118
channel F_Port Fibre channel fabric port (F_Port) is the switch port that connects the Fibre Channel (FC) fabric to a node. S4148U-ON switches support F_Port. Enable Fibre channel F_Port mode globally using the feature fc domain-ID domain-ID command in CONFIGURATION mode. Enable Fibre channel F_Port - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 119
Configure FIP snooping 1 Enable the FIP snooping feature globally using the feature fip-snooping command in CONFIGURATION mode. 2 Before applying FIP snooping to a VLAN, ensure that the VLAN already contains Ethernet or LAG members that are enabled with FCF port mode. You can enable FCF mode on an - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 120
Number of VN Port Session Timeouts :0 Number of Session failures due to Hardware Config :0 OS10# show fcoe vlan * = Default VLAN VLAN FC-MAP FCFs Enodes Sessions *1 - - - - 100 0X0EFC00 1 2 17 OS10# show fcoe system Mode: FIP Snooping Bridge FCOE VLAN List (Operational) : 1, 100 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 121
The F_Port and NPG modes are mutually exclusive. If you have already configured a vfabric in F_Port mode, while configuring vfabrics in NPG mode, disable the F_Port mode. The existing vfabric is removed when you disable F_Port mode and you need to configure new vfabrics in NPG mode. If you are - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 122
Switch Zoning Parameters Default Zone Mode: Allow Active ZoneSet: set Members fibrechannel1/1/1 fibrechannel1/1/2 fibrechannel1/1/3 fibrechannel1/1/4 fibrechannel1/1/5 fibrechannel1/1/6 fibrechannel1/1/7 fibrechannel1/1/8 fibrechannel1/1/9 fibrechannel1/1/10 fibrechannel1/1/11 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 123
fcoe fka-adv-period 8 fcoe vlan-priority 3 OS10# show vfabric Fabric Name 10 Fabric Type NPG Fabric Id 10 Vlan Id 100 FC-MAP 0xEFC01 Vlan priority 3 FCF Priority 128 FKA-Adv-Period Enabled,8 Config-State ACTIVE Oper-State DOWN Members OS10# show running-configuration vfabric ! vfabric 10 name 10 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 124
OS10(config)# fc zoneset set OS10(conf-fc-zoneset-set)# member hba1 OS10(conf-fc-zoneset-set)# exit OS10(config)# vfabric 100 OS10(conf-vfabric-100)# zoneset activate set OS10(conf-vfabric-100)# zone default-zone permit View FC zone configuration OS10(config-fc-zone-hba1)# show configuration ! fc - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 125
Command Mode Usage Information Example Not configured EXEC None OS10# clear fcoe database vlan 100 enode aa:bb:cc:00:00:00 Supported Releases 10.4.0E(R1) or later clear fcoe statistics Clears FCoE statistics for specified interface. Syntax clear fcoe statistics [interface interface-type - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 126
fcoe statistics interface ethernet 1/1/1 OS10# clear fcoe statistics interface port-channel 5 Supported Releases 10.4.0E(R1) or later fc alias Creates an FC alias. -fc-alias-test)# member wwn 20:25:78:2b:cb:6f:65:57 Supported Releases 10.3.1E or later fc zone Creates an FC zone and adds members - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 127
Information The no version of this command removes the FC zoneset. Example OS10(config)# fc zoneset set OS10(conf-fc-zoneset-set)# member hba1 Supported Releases 10.3.1E or later fcoe Adds FCoE parameters to vfabric. Syntax Parameters fcoe {fcmap fc-map | fcf-priority fcf-priority-value | fka - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 128
The no version of this command resets the number of sessions to the default value. Example OS10(config)# fcoe max-sessions-per-enodemac 64 Supported Releases 10.4.0E(R1) or later feature fc Enables the F_Port globally. Syntax feature fc domain-id domain-id Parameters domain-id - Enter the - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 129
feature fip-snooping None Disabled CONFIGURATION The no version of this command disables FIP snooping. Example OS10(config)# feature fip-snooping Supported Releases 10.4.0E(R1) or later fip-snooping enable Enables FIP snooping on specified VLAN. Syntax fip-snooping enable Parameters None - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 130
of this command resets the port mode to ENode. Example OS10(config)# interface ethernet 1/1/32 OS10(conf-if-eth1/1/32)# fip-snooping port-mode fcf Supported Releases 10.4.0E(R1) or later member (alias) Add members to existing FC aliases. Identify a member by an FC alias, a World Wide Name (WWN - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 131
config-fc-zone-hba1)# member wwn 21:00:00:24:ff:7b:f5:c8 Supported Releases 10.3.1E or later member (zoneset) Adds zones to an existing zoneset. (config)# fc zoneset set OS10(conf-fc-zoneset-set)# member hba1 Supported Releases 10.3.1E or later name Configures a vfabric name. Syntax name - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 132
:00:24:ff:7b:f5:c9 20:25:78:2b:cb:6f:65:57 OS10# Supported Releases 10.3.1E or later show fc ns switch Displays the details of FC NS switch = 2 Switch Name Domain Id Switch Port FC-Id Port Name Node Name Class of Service Symbolic Port Name Symbolic Node Name Port Type 10:00:14:18:77:20:8d:cf - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 133
Id Switch Port FC-Id Port Name Node Name Class of Service Symbolic Port Name Symbolic Node Name Port Type Registered with NameServer 10:00:00:90:fa:b8:22:19 21:00:00:24:ff:7b:f5:c8 Supported Releases 10.3.1E or later show fc statistics Displays the FC statistics. Syntax show fc statistics - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 134
configured Command Mode EXEC Usage Information None Example OS10# show fc switch Switch Mode : FPORT Switch WWN : 10:00:14:18:77:20:8d:cf Supported Releases 10.3.1E or later show fc zone Displays the FC zones and the zone members. Syntax show fc zone [zone-name] Parameters zone-name - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 135
Supported Releases 10.3.1E or later 21:00:00:24:ff:7f:ce:ee 21:00:00:24:ff:7f:ce:ef show fc zoneset Displays - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 136
:d3:10:00:ec:f9:1f 20:35:78:2b:cb:6f:65:57 Supported Releases 10.3.1E or later show fcoe enode Displays the details of ENodes connected Interface VLAN FCFs Sessions d4:ae:52:1b:e3:cd ethernet1/1/54 100 1 5 Supported Releases 10.4.0E(R1) or later show fcoe fcf Displays the details of FCFs - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 137
Supported Releases 10.4.0E(R1) or later show fcoe sessions Displays the details of established FCoE 02 01:00:02 31:00:0e:fc:00:00:00:00 21:00:0e:fc:00:00:00:00 Supported Releases 10.4.0E(R1) or later show fcoe statistics Displays the statistical details of FCoE control plane. Syntax Parameters - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 138
None Not configured EXEC None OS10# show fcoe system Mode: FIP Snooping Bridge FCOE VLAN List (Operational) : 1, 100 FCFs : 1 Enodes : 2 Sessions : 17 Supported Releases 10.4.0E(R1) or later show fcoe vlan Displays the details of FIP snooping operational VLANs and the attributes. Syntax - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 139
:ee:5f 100 Fc 1/1/20 10 FLOGI LOGGED_IN Eth 1/1/31 20:01:d4:ae:52:1a:f8:9c 100 Fc 1/1/20 10 FLOGI LOGGED_IN Supported Releases 10.4.0E(R1) or later show running-config vfabric Displays the running configuration for vfabric. Syntax Parameters Defaults Command Mode Usage Information Example show - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 140
/1/17 fibrechannel1/1/18 fibrechannel1/1/19 fibrechannel1/1/20 fibrechannel1/1/21 fibrechannel1/1/22 fibrechannel1/1/23 fibrechannel1/1/24 fibrechannel1/1/25:1 fibrechannel1/1/29:1 fibrechannel1/1/30:1 fibrechannel1/1/30:3 Supported Releases 10.3.1E or later 140 Fibre channel - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 141
version of this command removes the vfabric from the FC interface. Example OS10(config)# interface fibrechannel 1/1/1 OS10(conf-if-fc1/1/1)# vfabric 100 Supported Releases 10.3.1E or later vlan Associate an existing VLAN ID to the vfabric to carry traffic. Create the VLAN ID before associating - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 142
between FC nodes in the absence of an active zoneset. Example OS10(config)# vfabric 100 OS10(conf-vfabric-100)# zone default-zone permit Supported Releases 10.3.1E or later zoneset activate Activates an existing zoneset. You can activate only one zoneset in a vfabric. Syntax zoneset activate - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 143
4 Layer 2 802.1X Verifies device credentials prior to sending or receiving packets using the extensible authentication protocol (see 802.1X Commands). Link Aggregation Control Protocol (LACP) Exchanges information between two systems and automatically establishes a LAG between the systems (see - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 144
NOTE: OS10 supports only RADIUS as the back-end authentication server. The authentication process based on the results of the authentication process. The authenticator is executed on the Dell device. • Authentication-server - The authentication-server selects the authentication method, verifies - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 145
802.1X with EAP-MD5, EAP-OTP, EAP-TLS, EAP-TTLS, PEAPv0, PEAPv1, and MS-CHAPv2 with PEAP and all platforms support RADIUS as the authentication server. If the primary RADIUS server becomes unresponsive, the authenticator begins using a secondary RADIUS server if configured. NOTE: 802.1X is - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 146
Enable 802.1X 1 Enable 802.1X globally in CONFIGURATION mode. dot1x system-auth-control 2 Enter an interface or a range of interfaces in INTERFACE mode. interface range 3 Enable 802.1X on the supplicant interface only in INTERFACE mode. dot1x port-control auto Configure and verify 802.1X - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 147
reasons why the supplicant might fail to respond - the supplicant may have been booting when the request arrived, there may be a physical layer problem, and so on. 1 Configure the amount of time that the authenticator waits before re-transmitting an EAP Request Identity frame in INTERFACE mode - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 148
Failure quiet period If the supplicant fails the authentication process, the authenticator sends another Request Identity frame after 30 seconds by default. The quiet period is a transmit interval time after a failed authentication. The Request Identity Re-transmit interval is for an unresponsive - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 149
force-authorized (default) force-unauthorized auto This is an authorized state. A device connected to this port does not use the authentication process but can communicate on the network. Placing the port in this state is same as disabling 802.1X on the port. forceauthorized is the default mode. - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 150
Configure and verify reauthentication time period OS10(config)# interface range ethernet 1/1/7-1/1/8 OS10(conf-range-eth1/1/7-1/1/8)# dot1x re-authentication OS10(conf-range-eth1/1/7-1/1/8)# dot1x timeout re-authperiod 3600 OS10(conf-range-eth1/1/7-1/1/8)# show dot1x interface ethernet 1/1/7 802. - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 151
Port Auth Status: Re-Authentication: Tx Period: Quiet Period: Supplicant Timeout: Server Timeout: Re-Auth Interval: Max-EAP-Req: Host Mode: Auth PAE State: Backend State: UNAUTHORIZED Enable 120 seconds 120 seconds 45 seconds 60 seconds 3600 seconds 5 MULTI_HOST Initialize Initialize View - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 152
to 10). 2 INTERFACE The no version of this command resets the value to the default. OS10(conf-range-eth1/1/7-1/1/8)# dot1x max-req 4 Supported Releases 10.2.0E or later dot1x port-control Controls the 802.1X authentication performed on the interface. Syntax dot1x port-control {force-authorized - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 153
The no version of this command resets the value to the default. Example OS10(conf-range-eth1/1/7-1/1/8)# dot1x timeout quiet-period 120 Supported Releases 10.2.0E or later dot1x timeout re-authperiod Sets the number of seconds between re-authentication attempts. Syntax dot1x timeout re - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 154
65535). 30 seconds INTERFACE The no version of this command resets the value to the default. OS10(conf-range-eth1/1/7-1/1/8)# dot1x timeout supp-timeout 45 Supported Releases 10.2.0E or later dot1x timeout tx-period Sets the number of seconds that the device waits for a response to an EAP-request - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 155
and State info for Supplicant: 01:80:c2:00:01:1c Port Auth Status: UNAUTHORIZED Untagged VLAN id: 1 Auth PAE State: Initialize Backend State: Idle Supported Releases 10.2.0E or later Layer 2 155 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 156
Link aggregation control protocol Group Ethernet interfaces to form a single link layer interface called a LAG or port-channel. Aggregating multiple links between physical interfaces creates a single logical LAG, which balances traffic across the member links within an aggregated Ethernet bundle and - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 157
Configure LACP OS10(config)# lacp system-priority 65535 OS10(config)# interface range ethernet 1/1/7-1/1/8 OS10(conf-range-eth1/1/7-1/1/8)# lacp port-priority 4096 OS10(conf-range-eth1/1/7-1/1/8)# lacp rate fast Verify LACP configuration OS10(conf-range-eth1/1/7-1/1/8)# do show running-configuration - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 158
Configure LACP timeout OS10(conf-if-eth1/1/29)# lacp rate fast View port status OS10# show lacp port-channel Port-channel 20 admin up, oper up, mode lacp Actor System ID: Priority 32768, Address f8:b1:56:00:02:33 Partner System ID: Priority 4096, Address 10:11:22:22:33:33 Actor Admin Key 20, Oper - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 159
verify LAG port configuration bravo# show interface ethernet 1/1/29 Ethernet 1/1/29 is up, line protocol is up Port is part of Port-channel Hardware is Dell EMC Eth, address is 90:b1:1c:f4:9b:a2 Current address is 90:b1:1c:f4:9b:a2 Pluggable media present, QSFP-PLUS type - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 160
0 runts, 0 giants, 0 throttles 0 CRC, 0 overrun, 465 discarded Output statistics: 7840 packets, 938965 octets 0 64-byte pkts,1396 over 64-byte pkts, 6444 over 127-byte pkts 0 over 255-byte pkts, 0 over 511-byte pkts, 0 over 1023-byte pkts 7840 Multicasts, 0 Broadcasts,0 Unicasts 0 throttles, 0 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 161
| passive} • number - Enter the port-channel group number (1 to 128). The maximum number of port-channels is 128. The maximum physical port/maximum NPU is supported. • mode - Enter the interface port-channel mode. Layer 2 161 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 162
10 mode active OS10(conf-if-eth1/1/10)# exit OS10(config)# interface ethernet 1/1/11 OS10(conf-if-eth1/1/11)# channel-group 10 mode active Supported Releases 10.2.0E or later clear lacp counters Clears the statistics for all interfaces for LACP groups. Syntax clear lacp counters [interface port - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 163
The no version of this command resets the maximum bundle size to the default value. OS10(conf-if-po-10)# lacp max-bundle 10 Supported Releases 10.2.0E or later lacp port-priority Sets the priority for the physical interfaces for LACP. Syntax Parameters Default Command Mode Usage Information - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 164
each device. The no version of this command resets the system priority to the default value. OS10(config)# lacp system-priority 32768 Supported Releases 10.2.0E or later show lacp counter Displays information about LACP statistics. Syntax show lacp counter [interface port-channel channel-number - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 165
=passive LACP_Timeout=Long Timeout(30s) Synchronization=IN_SYNC Collecting=true Distributing=true Partner Admin State=BCEGIKNP Partner Oper State=BDEGIKMO Supported Releases 10.2.0E or later show lacp neighbor Displays information about LACP neighbors. Syntax show lacp neighbor [interface port - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 166
Partner Port: 178 Partner Port Priority: 32768 Partner Oper Key: 1 Partner Oper State:aggregation synchronization collecting distributing defaulted expired Supported Releases 10.2.0E or later show lacp port-channel Displays information about LACP port-channels. Syntax show lacp port-channel - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 167
system ID is different for each device. OS10# show lacp system-identifier Actor System ID: Priority 32768, Address 90:b1:1c:f4:9b:8a Supported Releases 10.2.0E or later Link layer discovery protocol LLDP enables a LAN device to advertise its system and receive system information from adjacent LAN - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 168
configuration information. These sub-types are management TLVs, IEEE 802.1, IEEE 802.3, and TIA-1057 organization-specific TLVs. Optional TLVs OS10 supports basic TLVs, IEEE 802.1, and 802.3 organizationally-specific TLVs, and TIA-1057 organizationally-specific TLVs. A basic TLV is an optional TLV - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 169
and bit rate settings of the sending device. Also configuration/status indicates whether the current settings are due to auto-negotiation or due to manual configuration. 127 - Power via MDI Not supported. 127 - Maximum frame size Maximum frame size capability of the MAC and PHY. Layer 2 169 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 170
address LCI • Emergency call services ELIN 127/4 - Extended Power requirements, priority, and power status. power-via-MDI LLDP-MED capabilities TLV The LLDP-MED capabilities TLV communicates the types of TLVs that the endpoint device and the network connectivity device support. The value of the - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 171
LLDP-MED capabilities Bit 0 Bit 1 Bit 2 Bit 3 Bit 4 Bit 5 Bits 6-15 LLDP-MED capabilities Network policy Location ID Extended power via MDI-PSE Extended power via MDI-PD Inventory Reserved LLDP-MED device types 0 1 2 3 4 5-255 Type not defined Endpoint class 1 Endpoint class 2 Endpoint class 3 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 172
and similar applications supporting streaming video services that require specific network policy treatment. 8 - Video signaling Used only if video control packets use a separate network policy than video data. 9-255 - Reserved - Define network policies You can manually - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 173
2 Enter the multiplier value for the hold time in CONFIGURATION mode. lldp holdtime-multiplier 3 Enter the delay (in seconds) for LLDP initialization on any interface in CONFIGURATION mode. lldp reinit Configure LLDPDU timer OS10(config)# lldp timer 60 OS10(config)# do show lldp timers LLDP Timers: - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 174
Enable LLDP OS10(config)# interface ethernet 1/1/1 OS10(conf-if-eth1/1/1)# lldp transmit OS10(conf-if-eth1/1/1)# lldp receive Disable LLDP globally OS10(config)# no lldp enable Disable and re-enable LLDP on management ports By default, LLDP is enabled on management ports. You can disable or enable - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 175
packets per interval. Change the number of packets a device sends per second - up to 10. Rapid availability is crucial for applications such as emergency call service location (E911). Layer 2 175 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 176
• Enable fast start repeat count which is the number of packets sent during activation in CONFIGURATION mode (1 to 10, default 3). lldp-med fast-start-repeat-count number Configure fast start repeat count OS10(config)# lldp med fast-start-repeat-count 5 View LLDP configuration • View the LLDP - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 177
Router Enabled System Capabilities: Repeater, Bridge, Router Remote Max Frame Size: 0 Remote Aggregation Status: false MAC PHY Configuration: Auto-neg supported: 1 Auto-neg enabled: 1 Auto-neg advertised capabilities: 10BASE-T half duplex mode, 10BASE-T full duplex mode, 100BASE-TX half duplex mode - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 178
, L2 Priority: 6, DSCP Value: 46 Inventory Management: H/W Revision : 12.1.1 F/W Revision : 10.1.9750B S/W Revision : 10.1.9750B Serial Number : B11G152 Manufacturer : Dell Model : S6010-ON Asset ID : E1001 Power-via-MDI: Power Type: PD Device Power Source: Local and PSE Power Priority - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 179
all Ethernet (PHY) interfaces, except on those interfaces where LLDP is manually disabled. The no version of this command disables LLDP globally irrespective of whether LLDP is manually enabled on an interface. Example OS10(config)# lldp enable Supported Releases 10.3.1E or later Layer 2 179 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 180
Information Example Enabled with network-policy TLV INTERFACE LLDP-MED communicates the types of TLVs that the endpoint device and the network connectivity device support. Use the no lldp med or lldp med disable command to disable LLDP-MED on a specific interface. OS10(conf-if-eth1/1/1)# lldp med - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 181
Supported Releases 10.2.0E or later lldp med network-policy Manually defines an LLDP-MED network policy. Syntax Parameters med network-policy 10 app voice vlan 10 vlan-type tag priority 2 dscp 1 Supported Releases 10.2.0E or later lldp med network-policy (Interface) Attaches or removes an - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 182
Command Mode Usage Information Example INTERFACE Attach only one network policy for per interface. OS10(conf-if-eth1/1/5)# lldp med network-policy add 1 Supported Release 10.2.0E or later lldp med tlv-select Configures the LLDP-MED TLV type to transmit or receive. Syntax lldp med tlv-select { - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 183
254). 30 seconds CONFIGURATION The no version of this command sets the LLDP timer back to its default value. OS10(config)# lldp timer 25 Supported Releases 10.2.0E or later lldp tlv-select basic-tlv Enables or disables TLV attributes to transmit and receive LLDP packets. Syntax Parameters lldp - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 184
conf-if-eth1/1/3)# lldp tlv-select dot1tlv port-vlan-id Example (Link Aggregation) OS10(conf-if-eth1/1/3)# lldp tlv-select dot1tlv link-aggregation Supported Releases 10.2.0E or later lldp tlv-select dot3tlv Enables or disables the dot3 TLVs to transmit in LLDP packets. Syntax Parameters lldp - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 185
ID: ethernet1/1/1 System Name: OS10 Capabilities: Bridge Router System description: Dell networking Operating system Port description: Connected to end point device Time To 20:1| Yes| Yes| No| No| No Network Polices : Supported Releases 10.2.0E or later show lldp errors Displays the LLDP - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 186
Example OS10# show lldp errors Total Memory Allocation Failures: 0 Total Input Queue Overflows: 0 Total Table Overflows: 0 Supported Release 10.2.0E or later show lldp med Displays the LLDP MED information for all the interfaces. Syntax Parameters Default Command Mode Usage Information Example - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 187
Router Enabled System Capabilities: Repeater, Bridge, Router Remote Max Frame Size: 0 Remote Aggregation Status: false MAC PHY Configuration: Auto-neg supported: 1 Auto-neg enabled: 1 Auto-neg advertised capabilities: 10BASE-T half duplex mode, 10BASE-T full duplex mode, 100BASE-TX half duplex mode - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 188
: 10.1.9750B S/W Revision : 10.1.9750B Serial Number : B11G152 Manufacturer : Dell Model : S6010-ON Asset ID : E1001 Power-via-MDI: Power Type: 120 Reinit-time in seconds: 6 Transmit interval in seconds: 30 Supported Releases 10.2.0E or later show lldp tlv-select interface Displays the - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 189
port-description system-name system-description system-cababilities management-address port-vlan mac-phy-config link-aggregation max-frame-size Supported Releases 10.2.0E or later show lldp traffic Displays LLDP traffic information including counters, packets transmitted and received, discarded - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 190
36 voice vlan 4 cos 3 Interface: ethernet 1/1/1,ethernet 1/1/3-5 Supported Releases 10.2.0E or later Media Access Control All Ethernet switching -time 0 Static MAC Address A static MAC address entry is one that you manually configure. A static entry is not subject to aging. • Create a static - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 191
Set Static MAC Address OS10(config)# mac address-table static 34:17:eb:f2:ab:c6 vlan 10 interface ethernet 1/1/5 MAC Address Table OS10 maintains a list of MAC address table entries. • View the contents of the MAC address table in EXEC mode. show mac address-table {dynamic | static} [address mac- - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 192
all dynamic entries from the address table. OS10# clear mac address-table dynamic all Example (VLAN) OS10# clear mac address-table dynamic vlan 20 Supported Releases 10.2.0E or later mac address-table aging-time Configures the aging time for entries in the L2 address table. Syntax Parameters - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 193
1 interface ethernet 1/1/30 Example (PortChannel) OS10(config)# mac address-table static 34:17:eb:02:8c:33 vlan 10 interface port-channel 1 Supported Releases 10.2.0E or later show mac address-table Displays information about the MAC address table. Syntax Parameters show mac address-table - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 194
-tree instance costs bandwidth and processing resources. When you enable MST, all ports in Layer 2 mode participate in MST. Keep in mind that OS10 only supports one MST region. Load balancing can be achieved using the MST protocol. When three VLANs are mapped to two MSTIs, VLAN 100 traffic takes - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 195
3 Ensure the same region name is configured in all the bridges running MST. 4 (Optional) Configure the revision number. Configure MST protocol When you enable MST globally, all L2 physical, port-channel, and VLAN interfaces are automatically assigned to MST instance (MSTI) zero (0). Within an MSTI - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 196
View VLAN instance mapping OS10# show spanning-tree mst configuration Region Name: force10 Revision: 100 MSTI VID 0 1,31-4093 1 2-10 2 11-20 3 21-30 View port forwarding/discarding state OS10# show spanning-tree msti 0 brief Spanning tree enabled protocol msti with force-version mst - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 197
Sts Cost Link-type Edge ethernet1/1/5 Root 128.276 128 500 FWD 0 AUTO No ethernet1/1/6 Altr 128.280 128 500 BLK 0 AUTO No Non-Dell hardware OS10 supports only one MST region. For a bridge to be in the same MST region as another, the three unique attributes (name, revision, and VLAN-to - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 198
to 30, default 15). spanning-tree mst forward-time seconds 2 Change the hello-time parameter in CONFIGURATION mode (1 to 10, default 2). Dell EMC recommends increasing the hello-time for large configurations (especially configurations with more ports). spanning-tree mst hello-time seconds 3 Change - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 199
ethernet1/1/6 128.280 128 500 BLK 0 32768 3417.4455.667f Interface Name Role PortID Prio Cost Sts Cost Link-type Edge ethernet1/1/5 Root 128.276 128 500 FWD 0 AUTO No ethernet1/1/6 Altr 128.280 128 500 BLK 0 AUTO No 128.150 Interface parameters Adjust two interface parameters to - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 200
the active network topology. OS10 supports BPDU filtering, BPDU guard, root BPDUs from an erroneous device. Enabling BPDU Filtering instructs the hardware to drop BPDUs and prevents flooding only resume operation from Shutdown state after manual intervention. Avoids bridging loops and preserves - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 201
To clear Error Disabled state: • Use the shutdown command on the interface. • Use the spanning-tree bpdufilter disable command to disable the BPDU guard on the interface. • Use the spanning-tree disable command to disable STP on the interface. 2 Enable STP BPDU guard in INTERFACE mode. spanning-tree - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 202
Boundary: NO bpdu filter : bpdu guard : bpduguard shutdown-on- violation :disable RootGuard: disable LoopGuard enable Bpdus (MRecords) sent 7, received 20 Interface Designated Name PortID Prio Cost Sts Cost Bridge ID PortID ethernet1/1/4 128.272 128 500 FWD 0 32769 90b1.1cf4.9d3b 128.272 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 203
instance related configuration. OS10(conf-mst)# instance 1 vlan 2-10 OS10(conf-mst)# instance 2 vlan 11-20 OS10(conf-mst)# instance 3 vlan 21-30 Supported Releases 10.2.0E or later name Assigns a name to the MST region. Syntax name region-name Parameters region-name - Enter a name for an MST - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 204
values for the revision number must match on all Dell hardware devices. If there are non-Dell devices, ensure the revision number value matches on all the devices (see Non-Dell Hardware). Example OS10(conf-mst)# revision 10 Supported Releases 10.2.0E or later spanning-tree bpdufilter Enables - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 205
port receives a BPDU, it is placed in the Error-Disabled state as a protective measure. OS10(conf-if-eth1/1/4)# spanning-tree bpduguard enable Supported Releases 10.2.0E or later spanning-tree disable Disables the spanning-tree mode configured with the spanning-tree mode command globally on the - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 206
mode. You can also change to RSTP/MST mode. OS10(config)# spanning-tree mode rstp Example (MST) OS10(config)# spanning-tree mode mst Supported Releases 10.2.0E or later spanning-tree mst Configures an MST instance and determines root and bridge priorities. Syntax spanning-tree mst instance - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 207
several ports have the same cost. OS10(conf-if-eth1/1/1)# spanning-tree msti 1 priority 0 OS10(conf-if-eth1/1/1)# spanning-tree msti 1 cost 3 Supported Releases 10.2.0E or later spanning-tree mst configuration Enters MST mode to configure MSTP from Configuration mode. Syntax spanning-tree mst - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 208
CONFIGURATION The no version of this command enables spanning tree on the specified MST instance. OS10(config)# spanning-tree mst 10 disable Supported Releases 10.4.0E(R1) or later spanning-tree mst force-version Configures a forced version of STP to transmit BPDUs. Syntax Parameters spanning - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 209
time interval value in seconds (1 to 10). 2 seconds CONFIGURATION Dell EMC recommends increasing the hello-time for large configurations - especially value to the default. OS10(config)# spanning-tree mst hello-time 5 Supported Releases 10.2.0E or later spanning-tree mst mac-flush-threshold Sets - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 210
for the port. The command configuration applies to all common IST (CIST) in the MST region. OS10(config)# spanning-tree mst max-hops 30 Supported Releases 10.2.0E or later spanning-tree port Sets the port type as the EdgePort. Syntax spanning-tree port type edge Parameters None Default Not - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 211
0 1,7-4093 1 2 2 3 3 4 4 5 5 6 Supported Releases 10.2.0E or later show spanning-tree msti Displays MST instance information. Syntax Parameters show spanning-tree msti [instance-number [brief | guard | interface interface]] • - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 212
Example (Interface) OS10# show spanning-tree msti 1 interface ethernet 1/1/1 ethernet1/1/1 of vlan1 is root Forwarding Edge port:no (default) port guard :none (default) Link type is point-to-point (auto) Boundary :internal bpdu filter : bpdu guard : bpduguard shutdown-on- violation :disable - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 213
By default, each VLAN instance is assigned default bridge priority 32768. For example, all three instances have the same forwarding topology. Traffic load balancing is not achievable with this kind of priority assignment. You must assign each instance a different priority to achieve load balancing, - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 214
ethernet1/1/5 128.276 128 500 FWD 0 32768 3417.4455.667f 128.146 ethernet1/1/6 128.280 128 500 BLK 0 32768 3417.4455.667f 128.150 Interface Name Role PortID Prio Cost Sts Cost Link-type Edge ethernet1/1/5 Root 128.276 128 500 FWD 0 AUTO No ethernet1/1/6 Altr 128.280 128 500 BLK 0 AUTO - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 215
ethernet1/1/5 128.276 128 500 FWD 0 4097 90b1.1cf4.a523 ethernet1/1/6 128.280 128 500 FWD 0 4097 90b1.1cf4.a523 ethernet1/1/7 128.284 128 200000000 FWD 0 32769 0000.0000.0000 ethernet1/1/8 128.288 128 200000000 FWD 0 32769 0000.0000.0000 ethernet1/1/9 128.292 128 200000000 FWD 0 32769 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 216
loop guard on a port or port-channel interface in INTERFACE mode. no spanning-tree guard loop Port enabled with loop guard conditions • Loop guard is supported on any STP-enabled port or port-channel interface in RPVST+ mode. • You cannot enable root guard and loop guard at the same time on - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 217
to 10, default 2). With large configurations (involving more number of ports), Dell EMC recommends increasing the hello-time. spanning-tree vlan vlan-id hello-time OS10# clear spanning-tree counters interface port-channel 10 Supported Releases 10.2.0E or later clear spanning-tree detected-protocol - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 218
direction. • events - Debugs PVST events. Default Command Mode Usage Information Example Not configured EXEC None OS10# debug spanning-tree bpdu rx Supported Releases 10.2.0E or later show spanning-tree vlan Displays RPVST+ status and configuration information by VLAN ID. Syntax show spanning - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 219
0000.0000 128.288 0000.0000.0000 128.292 0000.0000.0000 128.296 0000.0000.0000 128.300 0000.0000.0000 128.304 Supported Releases 10.2.0E or later spanning-tree bpdufilter Enables or disables BPDU filtering on an interface. Syntax spanning-tree bpdufilter {enable | disable} Parameters • enable - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 220
configurations are mutually exclusive. Configuring one overwrites the other from the active configuration. INTERFACE OS10(conf-if-eth1/1/4)# spanning-tree guard root Supported Releases 10.2.0E or later spanning-tree mode Enables an STP type (RSTP, Rapid-PVST+, or MST). Syntax spanning-tree mode - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 221
new mode. You can also change to RSTP/MST mode. OS10(config)# spanning-tree mode rstp Example (MST) OS10(config)# spanning-tree mode mst Supported Releases 10.2.0E or later spanning-tree port Sets the port type as the EdgePort. Syntax spanning-tree port type edge Parameters None Default - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 222
to 4094. Enabled CONFIGURATION The no version of this command enables spanning tree on the specified VLAN. OS10(config)# spanning-tree vlan 100 disable Supported Releases 10.4.0E(R1) or later spanning-tree vlan forward-time Configures a time interval for the interface to wait in Blocking state or - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 223
to 10). Default Command Mode Usage Information Example 2 seconds CONFIGURATION Dell EMC recommends increasing the hello-time for large configurations - especially ports. OS10(config)# spanning-tree vlan 10 hello-time 5 Supported Releases 10.2.0E or later spanning-tree vlan mac-flush-threshold - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 224
Breaks the tie between the two bridges which compete for root bridge. Example OS10(conf-if-eth1/1/4)# spanning-tree vlan 10 priority 16 Supported Releases 10.2.0E or later spanning-tree vlan root Designates a device as primary or secondary root bridge. Syntax Parameters spanning-tree vlan - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 225
Usage Information Example None OS10(config)# spanning-tree vlan 1 root primary Supported Releases 10.2.0E or later Rapid spanning-tree protocol RSTP is similar to STP but provides faster convergence and interoperability with devices configured with STP - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 226
for forward-time, hello-time, and max-age, and overwrites the values set on other bridges participating in the RSTP group. Dell EMC recommends that only experienced network administrators change the RSTP group parameters. Poorly planned modification of the RSTP parameters can negatively affect - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 227
-time seconds • Change the hello-time in CONFIGURATION mode (1 to 10, default 2). With large configurations (especially those configurations with more ports) Dell EMC recommends increasing the hello-time. spanning-tree rstp hello-time seconds • Change the max-age in CONFIGURATION mode (6 to 40 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 228
Port cost Port priority Value that is based on the interface type. The previous table lists the default values. The greater the port cost, the less likely the port is selected to be a forwarding port. Influences the likelihood that a port is selected to be a forwarding port in case that several - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 229
the active network topology. OS10 supports BPDU filtering, BPDU guard, loop from an erroneous device. Enabling BPDU Filtering instructs the hardware to drop BPDUs and prevents flooding resume operation from the Shutdown state after manual intervention. Avoids bridging loops and preserves the - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 230
BPDUs using the spanning-tree guard loop command. After BPDUs are received, the port moves out of the Loop-Inconsistent (or blocking) state and transitions to an appropriate state determined by STP. Enabling loop guard on a per port basis enables it on all VLANs configured on the port. If you - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 231
all STP counters on the device per Ethernet interface or port-channel. OS10# clear spanning-tree counters interface port-channel 10 Supported Releases 10.2.0E or later show spanning-tree active Displays the RSTP configuration and information for RSTP-active interfaces. Syntax show spanning - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 232
500 BLK 0 AUTO No ethernet3/1/3 Root 128.252 128 500 FWD 0 AUTO No ethernet3/1/4 Altr 128.256 128 500 BLK 0 AUTO No Supported Releases 10.2.0E or later show spanning-tree interface Displays spanning-tree interface information for Ethernet and port-channels. Syntax Parameters show spanning - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 233
port receives a BPDU, it is placed in the Error-Disabled state as a protective measure. OS10(conf-if-eth1/1/4)# spanning-tree bpduguard enable Supported Releases 10.2.0E or later spanning-tree disable Disables the spanning-tree mode configured with the spanning-tree mode command globally on the - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 234
configurations are mutually exclusive. Configuring one overwrites the other from the active configuration. INTERFACE OS10(conf-if-eth1/1/4)# spanning-tree guard root Supported Releases 10.2.0E or later spanning-tree mode Enables an STP type (RSTP, Rapid-PVST+, or MST). Syntax spanning-tree mode - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 235
compatible manner to avoid frame misordering and duplication in known LAN protocols that are sensitive. OS10(config)# spanning-tree rstp force-version stp Supported Releases 10.2.0E or later spanning-tree rstp forward-time Configures a time interval for the interface to wait in the Blocking state - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 236
time interval value in seconds (1 to 10). 2 seconds CONFIGURATION Dell EMC recommends increasing the hello-time for large configurations (especially configurations Example OS10(config)# spanning-tree rstp mac-flush-threshold 255 Supported Releases 10.4.0E(R1) or later spanning-tree rstp max-age - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 237
the root bridge. A lower priority value increases the probability of the bridge becoming a root bridge. OS10(config)# spanning-tree rstp priority 200 Supported Releases 10.2.0E or later Virtual LANs VLANs segment a single flat L2 broadcast domain into multiple logical L2 networks. Each VLAN is - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 238
Default VLAN configuration OS10# show vlan Codes: * - Default VLAN, G-GVRP VLANs, R-Remote Port Mirroring VLANs, P-Primary, C-Community, I- Isolated Q: A-Access (Untagged), T-Tagged x-Dot1x untagged, X-Dot1x tagged G-GVRP tagged, M-Vlan-stack, H-VSN tagged i-Internal untagged, I-Internal - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 239
View configured VLANs OS10(config)# do show interface vlan Vlan 1 is up, line protocol is up Address is , Current address is Interface index is 69208865 Internet address is not set MTU 1532 bytes LineSpeed auto Flowcontrol rx off tx off ARP type: ARPA, ARP Timeout: 240 Last clearing of "show - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 240
Show running configuration OS10# show running-configuration ... ! interface ethernet1/1/5 ... switchport access vlan 604 no shutdown ! interface vlan1 no shutdown ... Trunk mode A trunk port can be a member of multiple VLANs set up on an interface. A trunk port can transmit traffic for all VLANs. To - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 241
1 Create a VLAN in CONFIGURATION mode (1 to 4093). interface vlan vlan-id 2 Assign an IP address and mask to the VLAN in INTERFACE-VLAN mode. ip address ip-address/prefix-length [secondary] • ip-address/prefix-length - Enter the IP address in dotted-decimal format (A.B.C.D/x). • secondary - Enter - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 242
View VLAN configuration OS10# show vlan Codes: * - Default VLAN, G-GVRP VLANs, R-Remote Port Mirroring VLANs, P-Primary, C-Community, I- Isolated Q: A-Access (Untagged), T-Tagged x-Dot1x untagged, X-Dot1x tagged G-GVRP tagged, M-Vlan-stack, H-VSN tagged i-Internal untagged, I-Internal tagged, - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 243
VLAN ID number (1 to 4093). Default VLAN 1 Command Mode CONFIGURATION Usage Information FTP, TFTP, MAC ACLs, and SNMP operations are not supported - IP ACLs are supported on VLANs only. The no version of this command deletes the interface. Example OS10(config)# interface vlan 10 OS10(conf-if - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 244
Status Description Q Ports * 1 up A Eth1/1/2-1/1/32 A Po40 200 up T Eth1/1/3:2 T Po40 A Eth1/1/31 320 up T Eth1/1/25:4 1/1/32 T Po40 A Eth1/1/3:1 Supported Releases 10.2.0E or later Port monitoring Port monitoring enables monitoring of ingress or egress traffic of one port to another - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 245
Remote port monitoring helps network administrators monitor and analyze traffic to troubleshoot network problems in a time-saving and efficient way. In a remote port traffic with the reserved L2 VLAN. Remote port monitoring supports monitoring sessions in which multiple source and destination ports - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 246
restriction on the VLAN IDs used for the reserved remote monitoring VLAN. Valid VLAN IDs are from 2 to 4093. The default VLAN ID is not supported. • In monitored traffic, packets that have the same destination MAC address as an intermediate or destination device in the path used by the reserved VLAN - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 247
15 egress sessions. - Bidirectional with 15 ingress and egress sessions. • You can monitor a source VLAN only through flow-based monitoring. Only ingress is supported in a flow-based source VLAN monitoring. • You cannot configure an interface with ERPM traffic as a source for an ERPM session. • You - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 248
using seq, permit, and deny statements in CONFIG-ACL mode. The ACL rules describe the traffic you want to monitor. Flow monitoring is supported for IPv4 ACLs, IPv6 ACLs, and MAC ACLs. seq sequence-number {deny | permit} {source [mask] | any | host ip-address} [count [byte]] [fragments] [threshold - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 249
Remote port monitoring on VLT In a network, devices configured with peer VLT nodes are considered as a single device. You can apply remote port monitoring (RPM) on the VLT devices in a network. In a failover case, the monitored traffic reaches the packet analyzer connected to the TOR through the VLT - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 250
Scenario Recommendation 1 Create an L2 ACL for the local session and attach it to the VLTi LAG interface. ! mac access-list span seq 10 permit any any capture session 10 ! interface ethernet 1/1/1 no shutdown switchport access vlan 1 mac access-group span in ! 2 Create a flow based local session - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 251
the value to the default. OS10(conf-mon-local-10)# destination interface port-channel 10 OS10(conf-mon-rspan-source-3)# destination remote-vlan 20 Supported Releases 10.2.0E or later flow-based Enables flow-based monitoring. The monitoring session can be one of the following: local, RPM, or ERPM - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 252
OS10(conf-mon-rspan-source-2)# flow-based enable OS10(conf-mon-erpm-source-3)# flow-based enable Supported Releases 10.2.0E or later ip Configures the IP time to live (TTL) value and the differentiated services code point (DSCP) value for the ERPM traffic. Syntax ip {ttl ttl-number | dscp dscp - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 253
ethernet1/1/1 both port N/A N/A 0 2 Destination is not resolved 6 ethernet1/1/2 remote-ip both port 11.11.11.1 2.2.2.1 0 2 session does not exist Supported Releases 10.2.0E or later shut Disables the monitoring session. The monitoring session can be one of the following: local, RPM, or - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 254
-source OS10(conf-mon-rspan-source-5)# no shut OS10(config)# monitor session 10 type erpm-source OS10(conf-mon-erpm-source-10)# no shut Supported Releases 10.2.0E or later source (Port Monitoring) Configures a source for port monitoring. The monitoring session can be one of the following: local - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 255
Default Command Mode Usage Information Example Not configured MONITOR-SESSION None OS10(config)# monitor session 10 OS10(conf-mon-erpm-source-10)# source-ip 10.16.132.181 destination-ip 172.16.10.11 gre-protocol 35006 Supported Releases 10.4.0E(R1) or later Layer 2 255 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 256
same autonomous system First (OSPF) area using link-state advertisements (LSAs). OS10 supports up to 10,000 OSPF routes for OSPFv2 to designate up to 8,000 one network to another. An ISP uses a transit AS to sell transit service to a customer network. When BGP operates inside an AS - AS1 or AS2 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 257
Classless interdomain routing BGPv4 supports classless interdomain routing (CIDR) with aggregate routes and AS paths. CIDR defines a network using a prefix consisting of an IP address and mask, resulting in efficient - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 258
allow BGP neighbors to inherit the same outbound policies. Instead of manually configuring each neighbor with the same policy, you can create a Multiprotocol BGP Multiprotocol BGP (MBGP) is an extension to BGP that supports multiple address families-IPv4 and IPv6. MBGP carries multiple sets of - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 259
to convey this information to the peers. As a result, the IPv6 routing information is exchanged over the IPv4 peers and vice versa. BGP routers that support IPv6 can set up BGP sessions using IPv6 peers. If the existing BGP-v4 session is capable of exchanging ipv6 prefixes, the same is used - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 260
6 Prefer external (EBGP) to internal (IBGP) paths or confederation EBGP paths, and prefer the path with the lowest IGP metric to the BGP next-hop. 7 The system deems the paths as equal and only performs the following steps if the criteria are not met: • Configure the IBGP multipath or EBGP multipath - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 261
Multiexit discriminators If two autonomous systems connect in more than one place, use a multiexit discriminator (MED) to assign a preference to a preferred path. MED is one of the criteria used to determine best path-other criteria may also impact selection. One AS assigns the MED a value. Other - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 262
AS path and next-hop The AS path is the AS list that all the prefixes listed in the update have passed through. The BGP speaker adds the local AS number when advertising to an EBGP neighbor. Any update that contains the AS path number 0 is valid. The next-hop is the IP address used to reach the - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 263
next new best path when the current best path is unavailable. The Add-Path capability to advertise more paths is supported only on IBGP peers-it is not supported on EBGP peers and BGP peer groups. Ignore router ID calculations Avoid unnecessary BGP best path transitions between external paths under - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 264
4-byte AS number configurations by default. The 4-byte support is advertised as a new BGP capability - 4-BYTE-AS, in the OPEN message. A BGP speaker that advertises 4-Byte-AS capability to a peer, and receives the same - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 265
• reuse = 750 • suppress = 2000 Timers • keepalive = 60 seconds • holdtime = 180 seconds Add-path Disabled Enable BGP BGP is disabled by default. The system supports one AS number - you must assign an AS number to your device. To establish BGP sessions and route traffic, configure at least one - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 266
BGP mode from CONFIGURATION mode (1 to 65535 for 2-byte, 1 to 4294967295 for 4byte). Only one AS number is supported per system. If you enter a 4-byte AS number, 4-byte AS support is enabled automatically. router bgp as-number 2 Enter a neighbor in ROUTER-BGP mode. neighbor ip-address 3 Add a remote - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 267
-source Loopback loopback0 no shutdown ! neighbor 192.168.12.2 remote-as 65123 update-source Loopback loopback0 no shutdown ! Configure Dual Stack OS10 supports dual stack for BGPv4 and BGPv6. Dual stack BGP allows simultaneous exchange of same IPv4 or IPv6 prefixes through different IPv4 and IPv6 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 268
template. Create a peer template before configuring any route policies for the template. NOTE: An outbound filter policy, distribute list or route map, is not supported on a peer group member. 1 Enable BGP, and assign the AS number to the local BGP speaker in CONFIGURATION mode, from 1 to 65535 for - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 269
between advertisement runs is 30 seconds For address family: Unicast BGP neighbor is ebgppg, peer-group external Update packing has 4_OCTET_AS support enabled Number of peers in this group 1 Peer-group members: View running configuration OS10(config-router-neighbor)# do show running-configuration - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 270
Received 23 messages 1 opens, 0 notifications, 1 updates 21 keepalives, 0 route refresh requests Sent 21 messages 1 opens, 0 notifications, 0 updates 20 keepalives, 0 route refresh requests Minimum time between advertisement runs is 30 seconds Minimum time before advertisements start is 0 seconds - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 271
Fast external fallover is enabled by default. To disable or re-enable it, use the [no] fast-external-fallover command. For the fast-external-fallover command to take effect on an established BGP session, you must reset the session using the clear ip bgp {* | peer-ipv4-address | peer-ipv6-address} - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 272
:03 OS10 dn_sm[2065]: Node.1-Unit.1:PRI:alert [os10:event], %Dell EMC (OS10) %BGP_NBR_BKWD_STATE_CHG: Backward state change occurred Hold Time expired , a session with a dynamic peer comes up. Passwords are not supported on BGPv4/v6 dynamic peers. Configure passive peering OS10(config)# router bgp - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 273
2 Enter a local-as number for the peer, and the AS values not prepended to announcements from the neighbors in ROUTERNEIGHBOR mode (1 to 4294967295). local-as as number [no prepend] 3 Return to ROUTER-BGP mode. exit 4 Enter a template name to assign to the peer-groups in ROUTER-BGP mode (up to 16 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 274
neighbor 17.1.1.2 remote-as 102 no shutdown ! address-family ipv4 unicast allowas-in 4 Show IP BGP OS10(config)# router bgp 100 OS10(config-router-bgp-100)# neighbor 172:16:1::2 OS10(config-router-neighbor)# remote-as 100 OS10(config-router-neighbor)# no shutdown OS10(config-router-neighbor)# - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 275
1 Assign an AS number in CONFIGURATION mode. router bgp as-number 2 Enter a neighbor and IP address (A.B.C.D) in ROUTER-BGP mode. neighbor ip-address 3 Enter Address Family mode in ROUTER-NEIGHBOR mode. address-family {[ipv4 | ipv6] [unicast]) 4 Allow the specified neighbor to send or receive - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 276
4 Enter the neighbor to apply the route map configuration in ROUTER-BGP mode. neighbor {ip-address} 5 Apply the route map to the neighbor's incoming or outgoing routes in ROUTER-BGP-NEIGHBOR-AF mode. route-map map-name {in | out) 6 Enter the peer group to apply the route map configuration in ROUTER- - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 277
OS10(config-router-bgp-10)# template zanzibar OS10(config-router-template)# weight 200 Enable multipath You can have one path to a destination by default, and enable multipath to allow up to 64 parallel paths to a destination. The show ip bgp network command includes multipath information for that - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 278
Configure clusters of routers where one router is a concentration router and the others are clients who receive their updates from the concentration router. 1 Assign an ID to a router reflector cluster in ROUTER-BGP mode. You can have multiple clusters in an AS. cluster-id cluster-id 2 Assign a - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 279
peers is to configure BGP confederations. As with route reflectors, Dell EMC recommends BGP confederations only for IBGP peering involving many IBGP bytes or 2 bytes. You cannot have a mix of router ASN support. confederation peers as-number [... as-number] Configure BGP confederations OS10(config - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 280
Route dampening When EBGP routes become unavailable, they "flap" and the router issues both WITHDRAWN and UPDATE notices. A flap occurs when a route is withdrawn, readvertised after being withdrawn, or has an attribute change. The constant router reaction to the WITHDRAWN and UPDATE notices causes - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 281
request to the neighbor and receives all the peer's updates. To use soft reconfiguration, or soft reset without preconfiguration, both BGP peers must support the soft route refresh capability. The soft route refresh advertises in the OPEN message sent when the peers establish a TCP session. To - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 282
neighbor, use the no activate command. Example OS10(conf-router-neighbor)# address-family ipv4 unicast OS10(conf-router-bgp-neighbor-af)# activate Supported Releases 10.2.0E or later add-path Allows the system to advertise multiple paths for the same destination without replacing previous paths - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 283
64 Example (IPv6) OS10(conf-router-bgpv6-af)# add-path both 64 Example (Receive) OS10(conf-router-bgpv6-af)# add-path receive Supported Releases 10.2.0E or later address-family Enters global address family configuration mode for the IP address family. Syntax Parameters address-family {[ipv4 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 284
mode. The no version of this command disables the advertisement-start time interval. Example OS10(conf-router-neighbor)# advertisement-start 30 Supported Releases 10.3.0E or later aggregate-address Summarizes a range of prefixes to minimize the number of entries in the routing table. Syntax - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 285
the best path. The no version of this command resets the value to the default. OS10(conf-router-bgp-10)# always-compare-med Supported Releases 10.2.0E or later bestpath as-path Configures the AS path selection criteria for best path computation. Syntax Parameters bestpath as-path {ignore - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 286
ID for multiple paths. The no version of this command resets the value to the default. Example OS10(conf-router-bgp-2)# bestpath router-id ignore Supported Releases 10.3.0E or later clear ip bgp Resets BGP IPv4 or IPv6 neighbor sessions. Syntax clear ip bgp {ipv4-address | ipv6-address - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 287
Usage Information Example Not configured EXEC To reset BGP IPv4 or IPv6 neighbor sessions, use this command. OS10# clear ip bgp 1.1.15.4 Supported Releases 10.3.0E or later clear ip bgp * Resets BGP sessions. The soft parameter (BGP soft reconfiguration) clears policies without resetting the - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 288
The no version of this command disables route reflection in a cluster. Example OS10(conf-router-bgp-2)# client-to-client reflection Supported Releases 10.2.0E or later bgp connection-retry-timer Configures a peer connection retry timer. Syntax Parameters Default Command Mode Usage Information - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 289
, an integer displays. The no version of this command resets the value to the default. OS10(conf-router-bgp-10)# cluster-id 3.3.3.3 Supported Releases 10.3.0E or later bgp dampening Enables BGP route-flap dampening and configures the dampening parameters. Syntax bgp dampening [half-life | reuse - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 290
the default metric value. OS10(conf-router-bgpv4-af)# default-metric 60 Example (IPv6) OS10(conf-router-bgpv6-af)# default-metric 60 Supported Releases 10.3.0E or later bgp default local-preference Changes the default local preference value for routes exchanged between internal BGP peers - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 291
indirectly connected are not valid for best path selection. The no version of this command removes multihop session. OS10(conf-router-neighbor)# ebgp-multihop 2 Supported Releases 10.3.0E or later enforce-first-as Enforces the first AS in the AS path of the route received from an external border - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 292
unreachability or link failure is detected. This only applies after you manually reset all existing BGP sessions. For the configuration to take effect, external fallover. OS10(conf-router-bgp-10)# fast-external-fallover Supported Releases 10.3.0E or later inherit template Configures a peer group - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 293
, use the show bgp config command. The no version of this command disables the feature. OS10(conf-router-bgp-10)# log-neighbor-changes Supported Releases 10.3.0E or later maximum-paths Configures the maximum number of equal-cost paths for load sharing. Syntax maximum-paths [ebgp number | ibgp - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 294
Default Command Mode Usage Information Example (EBGP) 64 paths ROUTER-BGP Dell EMC recommends not using multipath and add path simultaneously in a route reflector -router-bgp-neighbor-af)# maximum-prefix 20 100 warning-only Supported Releases 10.3.0E or later neighbor Creates a remote peer for - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 295
routes to IBGP peers. The no version of this command disables the nexthop calculation. OS10(conf-router-neighbor-af)# next-hop-self Supported Releases 10.3.0E or later non-deterministic-med Compares paths in the order they arrive. Syntax Parameters Default Command Mode Usage Information Example - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 296
outbound optimization. OS10(conf-router-bgp-10)# outbound-optimization Supported Releases 10.3.0E or later password Configures a password OSPF process (1 to 65535). • static - Enter to redistribute manually configured routes. Default Command Mode Usage Information Example (Connected) Disabled - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 297
removes all clients of a route reflector-the router no longer functions as a route reflector. Example OS10(conf-router-template)# route-reflector-client Supported Releases 10.3.0E or later router bgp Enables BGP and assigns an AS number to the local BGP speaker. Syntax Parameters router bgp - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 298
. The no version of this command resets the value to the default. OS10(conf-router-bgp-10)# router-id 10.10.10.40 Supported Releases 10.3.0E or later send-community Sends a community attribute to a BGP neighbor or peer group. Syntax send-community {extended | standard} Parameters • extended - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 299
102)# neighbor 32::1 OS10(conf-router-neighbor)# address-family ipv6 unicast OS10(conf-router-bgp-neighbor-af)# no sender-side-loop-detection Supported Releases 10.3.0E or later show ip bgp Displays information that BGP neighbors exchange. Syntax Parameters Default Command Mode Usage Information - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 300
00 800 9 8 i *> 3.1.5.0/24 80.1.1.2 1 00:00:11 00:00:00 800 9 8 i *> 3.1.6.0/24 80.1.1.2 1 00:00:11 00:00:00 800 9 8 i Total number of prefixes: 5 Supported Releases 10.3.0E or later show ip bgp ipv4 unicast Displays route information for BGP IPv4 routes. Syntax Parameters show ip bgp ipv4 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 301
bgp ipv4 unicast summary BGP router identifier 80.1.1.1 local AS number 102 Neighbor AS MsgRcvd MsgSent Up/Down State/Pfx 80.1.1.2 800 8 4 00:01:10 5 Supported Releases 10.3.0E or later show ip bgp ipv6 unicast Displays route information for BGP IPv6 routes. Syntax show ip bgp ipv6 unicast - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 302
Command Mode Usage Information EXEC • BGP neighbor - Displays the BGP neighbor address and its AS number. The last phrase in the line indicates whether the link between the BGP router and its neighbor is an external or internal one. If they are located in the same AS, the link is internal; - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 303
Example advertisedroutes OS10# show ip bgp ipv6 unicast neighbors 192:168:1::2 advertised-routes BGP local router ID is 100.1.1.1 Status codes: s suppressed, S stale, d dampened, h history, * valid, > best Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 304
you do not enable the peer group. If you enable the peer group, this line does not display. • BGP version - Displays the BGP version supported. • For address family - Displays IPv4 unicast as the address family. • BGP neighbor - Displays the name of the BGP neighbor. • Number of peers - Displays the - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 305
. Syntax soft-reconfiguration inbound Parameters None Default Not configured Command Modes ROUTER-BGP-NEIGHBOR-AF Usage Information This command is not supported on a peer-group level. To enable soft-reconfiguration for peers in a peer-group, this command must be enabled at a per-peer - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 306
values negotiate from peers. The no version of this command resets the value to the default. OS10(conf-router-bgp)# timers 30 90 Supported Releases 10.3.0E or later weight Assigns a default weight for routes from the neighbor interfaces. Syntax weight number Parameters number-Enter a number - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 307
Equal cost multi-path ECMP is a routing technique where next-hop packet forwarding to a single destination occurs over multiple best paths. OS10 uses a hashing algorithm to determine the next-hop when you enable ECMP. The hashing algorithm makes hashing decisions based on values in various packet - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 308
across the members. The no version of this command returns the value to the default. Example OS10(config)# hash-algorithm lag crc Supported Releases 10.3.0E or later link-bundle-utilization trigger-threshold Configures a threshold value to trigger monitoring of traffic distribution on an ECMP - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 309
) OS10(config)# load-balancing ingress-port enable Example (IP Selection) OS10(config)# load-balancing ip-selection destination-ip source-ip Supported Releases 10.2.0E or later show hash-algorithm Displays the hash-algorithm information. Syntax Parameters show hash-algorithm None Layer 3 309 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 310
EcmpAlgo - crc LabAlgo - crc Supported Releases 10.3.0E or later IPv4 routing OS10 supports IPv4 addressing including variable-length subnetting # show interface ethernet 1/1/1 Ethernet 1/1/1 is up, line protocol is up Hardware is Dell EMC Eth, address is 00:0c:29:98:1b:79 Current address is 00:0c - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 311
0 packets/sec, 0% of line rate Time since last interface status change: 3 weeks 1 day 20:54:37 Configure static routing You can configure a manual or static route for OSPF. • Configure a static route in CONFIGURATION mode. ip route ip-prefix/mask {next-hop | interface interface [route-preference - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 312
in dotted decimal format-A.B.C.D. • mac address-MAC address in nnnn.nnnn.nnnn format These entries do not age, and you can only remove them manually. To remove a static ARP entry, use the no arp ip-address command. Configure static ARP entries OS10(config)# interface ethernet 1/1/6 OS10(conf-if-eth1 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 313
The no version of this command disables the DHCP operations on the interface. OS10(config)# interface mgmt 1/1/1 OS10(conf-if-ma-1/1/1)# ip address dhcp Supported Releases 10.3.0E or later ip arp Configures static ARP and maps the IP address of the neighbor to a MAC address. Syntax ip arp mac - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 314
also invalid. The no version of this command disables IP ARP configuration. OS10(conf-if-eth1/1/6)# ip arp 10.1.1.5 08:00:20:b7:bd:32 Supported Releases 10.2.0E or later ip route Assigns a static route on the network device. Syntax ip route ip-prefix mask {next-hop | interface interface-type - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 315
192.168.1.1 - 00:01:e8:8b:39:43 - Vl 100 CP Internet 192.168.1.2 99 00:01:e8:8b:3c:01 Te 1/0 Vl 100 CP Supported Releases 10.2.0E or later show ip route Displays IP route information. Syntax show ip route [all | bgp | connected | ospf process-id | static | ip-prefix - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 316
.1.4.1 vlan103 200/0 01:16:56 Supported Releases 10.2.0E or later IPv6 routing OS10 supports IPv6 routing and addressing, including the L3 mode, IPv6 is not automatically re-enabled on the interface. You must manually reenable it. A link-local address is automatically generated when you re-enable - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 317
Dell EMC Eth, address is ec:f4:bb:fb:fa:30 Current address is ec:f4:bb:fb:fa:30 Pluggable media present, QSFP-PLUS type is QSFP_40GBASE_SR4 Wavelength is 850 Receive power reading is 0.0 Interface index is 17305562 Internet address is 20.20.20.1/24 Mode of IPv4 Address Assignment: MANUAL manually - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 318
ipv6 address ipv6-address/mask command. Enter the full 128-bit IPv6 address, including the network prefix and a 64-bit interface ID. You can also manually configure an IPv6 address by assigning: • A network prefix with the EUI-64 parameter using the ipv6 address ipv6-prefix eui64 command. A 64-bit - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 319
of hosts in the network when an organization changes its service provider. IPv6 provides the flexibility to add prefixes on router an RS message is received. The system manipulation of IPv6 stateless autoconfiguration supports the router side only. Neighbor Discovery (ND) messages advertise so - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 320
• ipv6 nd ra-lifetime seconds - (Optional) Sets the lifetime of a default router in RA messages (0 to 9000 milliseconds; default 3 times the max-ra-interval setting). 0 indicates that this router is not used as a default router. • ipv6 nd reachable-time milliseconds - (Optional) Sets the advertised - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 321
To disable IPv6 on an interface when a duplicate link-local address is detected, use the ipv6 nd dad disable-ipv6-on-failure command. To re-enable IPv6 after you resolve a duplicate link-local address, enter no ipv6 enable, followed by ipv6 enable. • Disable or re-enable IPv6 duplicate address - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 322
Enable IPv6 unreachable destination messaging OS10(config)# interface ethernet 1/1/8 OS10(conf-if-eth1/1/8)# ipv6 unreachables IPv6 hop-by-hop options A hop-by-hop header extension in an IPv6 packet contains options that are processed by all IPv6 routers in the packet's path. By default, hop-by-hop - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 323
Usage Information Example Not configured EXEC This command does not remove the static routes from the routing table. OS10# clear ipv6 route * Supported Releases 10.3.0E or later ipv6 address Configures a global unicast IPv6 address on an interface. Syntax Parameters Defaults Command Mode Usage - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 324
of this command disables the DHCP operations on the interface. OS10(config)# interface mgmt 1/1/1 OS10(conf-if-ma-1/1/1)# ipv6 address dhcp Supported Releases 10.3.0E or later ipv6 enable Enables and disables IPv6 forwarding on an interface configured with an IPv6 address. Syntax Parameters - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 325
OS10(conf-if-ma-1/1/1)# ipv6 address 2111:dddd:0eee::/64 eui-64 Supported Releases 10.4.0E(R1) or later ipv6 address link-local Configures a link a router boots up and IPv6 is enabled. Use this command to manually configure a link-local address to replace the autoconfigured address. For example, - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 326
disable Example: Enable DAD on link-local address OS10(config)# interface ethernet 1/1/1 OS10(conf-if-eth1/1/1)# ipv6 nd dad disable-ipv6-on-dad-failure Supported Releases 10.4.0E(R1) or later ipv6 nd hop-limit Sets the hop limit advertised in RA messages and included in IPv6 data packets sent - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 327
restores the default time interval used to send RA messages. OS10(config)# interface ethernet 1/2/3 OS10(conf-if-eth1/2/3)# ipv6 nd max-ra-interval 300 Supported Releases 10.4.0E(R1) or later ipv6 nd mtu Sets the maximum transmission unit (MTU) used on a local link in RA messages. Syntax ipv6 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 328
of this command restores the default MTU value advertised in RA messages. OS10(config)# interface ethernet 1/2/3 OS10(conf-if-eth1/2/3)# ipv6 nd mtu 2500 Supported Releases 10.4.0E(R1) or later ipv6 nd other-config-flag Sends RA messages that tell hosts to use stateful autoconfiguration to obtain - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 329
0 indicates that this router is not used as the default router. OS10(config)# interface ethernet 1/2/3 OS10(conf-if-eth1/2/3)# ipv6 nd max-ra-interval 300 Supported Releases 10.4.0E(R1) or later ipv6 nd reachable-time Sets the advertised time for which the router sees a neighbor to be up after it - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 330
that no reachable time is sent in RA messages. OS10(config)# interface ethernet 1/2/3 OS10(conf-if-eth1/2/3)# ipv6 nd reachable-time 1000 Supported Releases 10.4.0E(R1) or later ipv6 nd retrans-timer Sets the time between retransmitting neighbor solicitation messages. Syntax ipv6 nd retrans - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 331
if you do not assign an IP address to a peer interface, you must manually ping the peer to resolve the neighbor information. • The no version of OS10(config)# ipv6 route 2111:dddd:0eee::22/128 interface null 0 Supported Releases 10.2.0E or later ipv6 unreachables Enables the generation of error - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 332
0 Bgp 0 Connected 0 Static 0 Ospf Inter-area 0 NSSA External-1 0 NSSA External-2 0 Ospf External-1 0 Ospf External-2 0 Bgp Internal 0 Bgp External 0 Ospf Intra-area 0 Total 0 Non-Active Routes 0 0 0 0 0 0 0 0 0 0 0 0 0 Supported Releases 10.2.0E or later 332 Layer 3 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 333
use on IPv4 networks to establish multicast group memberships. IPv6 networks use Multicast listener discovery (MLD) to manage multicast groups. OS10 supports IGMPv2 and MLDv1 to manage the multicast group memberships on IPv4 and IPv6 networks. IGMP snooping IGMP snooping enables switches to use - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 334
• (Optional) You can disable IGMP snooping on specific VLAN interfaces using the no ip igmp snooping enable command in the VLAN INTERFACE mode. • IGMP snooping functions in a network with a multicast router that generates IGMP queries. The tables created are associated with the IGMP querier. Enable - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 335
IGMP snooping last member query response interval is 1000 ms IGMP snooping fast-leave is disabled on this interface IGMP snooping querier is enabled on this interface --more-- show ip igmp snooping mrouter Interface Router Ports vlan3031 port-channel31 vlan3032 port-channel31 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 336
snooping enable None Disabled CONFIGURATION The no version of this command disables the IGMP and MLD snooping. OS10(config)# ip igmp snooping enable Supported Releases 10.4.0E(R1) or later ip igmp snooping enable (VLAN) Enables IGMP and MLD snooping on the specified VLAN interface. Syntax ip - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 337
disables the IGMP and MLD querier processing on the VLAN. OS10(config)# interface vlan 100 OS10(conf-if-vl-100)# ip igmp snooping querier Supported Releases 10.4.0E(R1) or later show ip igmp snooping groups Displays the details of IGMP snooping group membership. Syntax show ip igmp snooping - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 338
and multicast IP IGMP Connected Group Membership address) Group Address 225.1.0.10 Interface vlan3031 Member Ports: ethernet1/1/6:1 Mode IGMPv2-Compat Supported Releases 10.4.0E(R1) or later show ip igmp snooping interface Displays the details of IGMP snooping interfaces. Syntax Parameters - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 339
member query response interval is 1000 ms IGMP snooping fast-leave is disabled on this interface IGMP snooping querier is enabled on this interface Supported Releases 10.4.0E(R1) or later show ip igmp snooping mrouter Displays the details of multicast router ports. Syntax show ip igmp snooping - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 340
port-channel31 Example (with VLAN) OS10# show ip igmp snooping mrouter vlan 3031 Interface Router Ports vlan3031 port-channel31 Supported Releases 10.4.0E(R1) or later show ipv6 mld snooping groups Displays the details of MLD snooping group membership. Syntax Parameters - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 341
ff00:0 and multicast IP MLD Connected Group Membership address) Group Address ff02::1:ff00:0 Interface vlan3031 Member Ports: port-channel31 Mode MLDv1-Compat Supported Releases 10.4.0E(R1) or later Open shortest path first OSPF routing is a link-state routing protocol that allows sending of - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 342
Areas allow you to further organize routers within the AS with one or more areas within the AS. Areas are valuable in that they allow subnetworks to hide within the AS-minimizing the size of the routing tables on all routers. An area within the AS may not see the details of another area's topology. - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 343
. Each router has a unique ID, written in decimal format-A.B.C.D. You do not have to associate the router ID with a valid IP address. To make troubleshooting easier, ensure the router ID is identical to the router's IP address. Backbone router A backbone router (BR) is part of the OSPF Backbone - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 344
Designated and backup designated routers OSPF elects a designated router (DR) and a backup designated router (BDR). The DR is responsible for generating LSAs for the entire multiaccess network. Designated routers allow a reduction in network traffic and in the size of the topological database. - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 345
second highest priority is the BDR. Priority rates from 0 to 255, with 255 as the highest number with the highest priority. OSPF route limit OS10 supports up to 16,000 OSPF routes. Within this range, the only restriction is on intra-area routes that scale only up to 1000 routes. Other - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 346
)# timers spf 2000 3000 4000 View OSPFv2 SPF throttling OS10(config-router-ospf-100)# do show ip ospf Routing Process ospf 100 with ID 12.1.1.1 Supports only single TOS (TOS0) routes It is Flooding according to RFC 2328 SPF schedule delay 1200 msecs, Hold time between two SPFs 2300 msecs Convergence - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 347
area in this router is 1, normal 1 stub 0 nssa Area (0.0.0.1) Number of interface in this area is 1 SPF algorithm executed 2 times OSPFv2 OSPFv2 supports IPv4 address families. OSPFv2 routers initially exchange hello messages to set up adjacencies with neighbor routers. The hello process establishes - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 348
ospf 100 ... Assign router identifier For managing and troubleshooting purposes, you can assign a router ID for View OSPFv2 status OS10# show ip ospf 10 Routing Process ospf 10 with ID 10.10.1.5 Supports only single TOS (TOS0) routes It is an Autonomous System Boundary Router It is Flooding according - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 349
CPU utilization and may impact adjacency stability in larger topologies. NOTE: Select the higher convergence levels only after checking with Dell Technical Support. When you disable fast-convergence, origination and arrival LSA parameters are set to 0 msec and 1000 msec, respectively. Setting the - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 350
-65535)# fast-converge 1 View fast convergence OS10(conf-router-ospf-65535)# do show ip ospf Routing Process ospf 65535 with ID 99.99.99.99 Supports only single TOS (TOS0) routes It is an Autonomous System Border Router It is an Area Border Router It is Flooding according to RFC 2328 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 351
7 Change the wait period between link state update packets sent out the interface in INTERFACE mode, from 1 to 3600. The default wait period is 1. The transmit delay must be the same on all routers in the OSPF network. ip ospf transmit-delay seconds Change parameters and view interface status OS10( - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 352
a grace LSA to all neighbors. In response, the helper router enters helper mode and sends an acknowledgement back to the restarting device. OS10 supports graceful restart helper mode. Use the graceful-restart role helper-only command to enable the helper mode in the ROUTER OSPF mode. OS10(config - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 353
included in the routing table in addition to the OSPF database? • Are you able to ping the IPv4 address of adjacent router interface? Troubleshooting OSPF with show commands • View a summary of all OSPF process IDs enabled in EXEC mode. show running-configuration ospf • View summary information of - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 354
Usage Information Example Not configured ROUTER-OSPF The no version of this command deletes an NSSA. OS10(conf-router-ospf-10)# area 10.10.1.5 nssa Supported Releases 10.2.0E or later area range Summarizes routes matching an address/mask at an area in ABRs. Syntax area area-id range ip-address - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 355
configured ROUTER-OSPF The no version of this command disables the route summarizations. OS10(conf-router-ospf-10)# area 0 range 10.1.1.4/8 no-advertise Supported Releases 10.2.0E or later area stub Defines an area as the OSPF stub area. Syntax area area-id stub [no-summary] Parameters • area - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 356
Command Mode EXEC Usage Information This command clears all entries in the OSPF routing table. Example OS10# clear ip ospf 3 process Supported Releases 10.2.0E or later clear ip ospf statistics Clears OSPF traffic statistics. Syntax clear ip ospf [instance-number] statistics Parameters - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 357
Not configured ROUTER-OSPF Convergence level 1 (optimal) meets most convergence requirements. Only select higher convergence levels following consultation with Dell Technical Support. The no version of this command disables the fast-convergence configuration. OS10(conf-router-ospf-10)# fast-converge - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 358
vendors to ensure that all routers use the same cost. If you manually configure the cost, the calculated cost based on the reference bandwidth does )# interface vlan 10 OS10(conf-if-vl-1)# ip ospf cost 10 Supported Releases 10.2.0E or later ip ospf dead-interval Sets the time interval since - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 359
packets. The no version of the this command resets the value to the default. Example OS10(conf-if-vl-10)# ip ospf hello-interval 30 Supported Releases 10.2.0E or later ip ospf message-digest-key Enables OSPF MD5 authentication and sends an OSPF message digest key on the interface. Syntax - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 360
does not establish. The no version of this command disables the IP OSPF mtu-ignore configuration. OS10(conf-if-vl-10)# ip ospf mtu-ignore Supported Releases 10.2.0E or later ip ospf network Sets the network type for the interface. Syntax ip ospf network {point-to-point | broadcast} Parameters - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 361
avoid unnecessary retransmission. The no version of this command resets the value to the default. OS10(conf-if-eth1/1/6)# ip ospf retransmit-interval 20 Supported Releases 10.2.0E or later ip ospf transmit-delay Sets the estimated time required to send a link state update packet on the interface - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 362
version of this command resets the value to the default. OS10(config)# router ospf 10 OS10(conf-router-ospf-10)# maximum-paths 1 Supported Releases 10.2.0E or later redistribute Redistributes information from another routing protocol or routing instance to the OSPFv2 process. Syntax Parameters - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 363
of this command disables the router ID configuration. OS10(config)# router ospf 10 OS10(conf-router-ospf-10)# router-id 10.10.1.5 Supported Releases 10.2.0E or later router ospf Enters Router OSPF mode and configures an OSPF instance. Syntax router ospf instance-number Parameters instance - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 364
interface in this area is 3 SPF algorithm executed 38 times Area ranges are Supported Releases 10.2.0E or later show ip ospf asbr Displays all the ASBR visible configured Command Mode EXEC Usage Information You can isolate problems with external routes. External OSPF routes are calculated by - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 365
111.2.1.1 112.2.1.1 112.2.1.1 Age 1287 1458 1458 1372 1372 Seq# 0x80000008 0x80000008 0x80000008 0x80000008 0x80000008 Summary Network (Area 0.0.0.0) Supported Releases 10.2.0E or later Checksum 0x9bf2 0x515a 0x5552 0x0485 0xbab2 0xbeaa Checksum 0xd2b1 0x1b8f 0x198f 0x287c 0x267c Link count - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 366
: Summary Asbr Link State ID: 8.1.1.1 Advertising Router: 2.2.2.2 LS Seq Number: 0x80000001 Checksum: 0xB595 Length: 28 Network Mask: /0 TOS: 0 Metric: 0 Supported Releases 10.2.0E or later show ip ospf database external Displays information about the AS external (Type 5) LSAs. Syntax Parameters - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 367
Advertising Router: 112.2.1.1 LS Seq Number: 0x80000008 Checksum: 0xd2b1 Length: 32 Network Mask: /24 Attached Router: 111.2.1.1 Attached Router: 112.2.1.1 Supported Releases 10.2.0E or later show ip ospf database nssa external Displays information about the NSSA-External (Type 7) LSA. Syntax - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 368
Parameters Default Command Mode Usage Information process-id - (Optional) Displays NSSA-External (Type7) LSA information for a specified OSPF Process ID. If you do not enter a Process ID, this command applies only to the first OSPF process. Not configured EXEC • LS Age - Displays the LS age. • - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 369
LS Seq Number: 0x80000001 Checksum: 0xA303 Length: 36 Network Mask: /24 Metric Type: 2 TOS: 0 Metric: 20 Forward Address: 0.0.0.0 External Route Tag: 0 Supported Releases 10.2.0E or later show ip ospf database opaque-area Displays information about the opaque-area (Type 10) LSA. Syntax show ip - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 370
-10 Area Local Opaque Link State ID: 8.1.1.2 Advertising Router: 2.2.2.2 LS Seq Number: 0x80000008 Checksum: 0x83B8 Length: 28 Opaque Type: 8 Opaque ID: 65794 !! ! Supported Releases 10.2.0E or later show ip ospf database opaque-as Displays information about the opaque-as (Type 11) LSAs. Syntax - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 371
-9 Link Local Opaque Link State ID: 8.1.1.1 Advertising Router: 2.2.2.2 LS Seq Number: 0x80000007 Checksum: 0x9DA1 Length: 28 Opaque Type: 8 Opaque ID: 65793 Supported Releases 10.2.0E or later show ip ospf database router Displays information about the router (Type 1) LSA. Syntax show ip ospf - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 372
Transit Network (Link ID) Designated Router address: 111.2.1.1 (Link Data) Router Interface address: 111.2.1.1 Number of TOS metric: 0 TOS 0 Metric: 1 Supported Releases 10.2.0E or later show ip ospf database summary Displays the network summary (Type 3) LSA routing information. Syntax show ip - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 373
Link State ID: 115.1.1.0 Advertising Router: 111.111.111.1 LS Seq Number: 0x800001e8 Checksum: 0x4a67 Length: 28 Network Mask: /24 TOS: 0 Metric: 0 Supported Releases 10.2.0E or later show ip ospf interface Displays the configured OSPF interfaces. You must enable OSPF to display output. Syntax - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 374
Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5 Simple password authentication enabled Neighbor Count is 0, Adjacent neighbor count is 0 Supported Releases 10.2.0E or later show ip ospf routes Displays OSPF routes received from neighbors along with parameters like cost, next - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 375
Cost 1 1 1 2 2 Nexthop 111.1.1.2 111.2.1.2 110.1.1.2 110.1.1.2 110.1.1.2 Interface Vl 3051 Vl 3053 Vl 3050 Vl 3050 Vl 3050 Area 0 0 0 0 0 Supported Releases 10.2.0E or later summary-address Configures a summary address for an ASBR to advertise one external route as an aggregate, for all - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 376
version of this command resets the value to the default. OS10(config)# router ospf 10 OS10(conf-router-ospf-10)# timers lsa arrival 2000 Supported Releases 10.2.0E or later timers spf Enables shortest path first (SPF) throttling to delay an SPF calculation when a topology change occurs. Syntax - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 377
(config-router-ospf-100)# timers spf 1200 2300 3400 OS10(config-router-ospf-100)# do show ip ospf Routing Process ospf 100 with ID 12.1.1.1 Supports only single TOS (TOS0) routes It is Flooding according to RFC 2328 SPF schedule delay 1200 msecs, Hold time between two SPFs 2300 msecs Convergence - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 378
OSPFv3 OSPFv3 is an IPv6 link-state routing protocol that supports IPv6 unicast address families (AFs). OSPFv3 is disabled by default. You must configure at least one interface, either physical or loopback. The OSPF process automatically - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 379
SPF algorithm executed 42 times Area (0.0.0.1) Number of interface in this area is 1 SPF algorithm executed 42 times Configure Stub Areas The Type 5 LSAs are not flooded into stub areas. The ABR advertises a default route into the stub area to which it is attached. Stub area routers use the - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 380
199.205.134.103 42 202.254.156.15 54 0x80000001 12 0x80000001 12 ethernet1/1/3 ethernet1/1/3 Enable Passive Interfaces A passive interface is one that does not send or receive routing information. Configuring an interface as a passive interface suppresses routing updates (both receiving and - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 381
. The authentication header is inserted after the IP header with a value of 51. MD5 and SHA1 authentication types are supported; encrypted and unencrypted keys are supported. • ESP encryption encapsulates data, enabling the protection of data that follows in the datagram. The ESP extension header is - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 382
the text string used in the authentication type. All neighboring OSPFv3 routers must share the key to exchange information. Only a non-encrypted key is supported. For MD5 authentication, the non-encrypted key must be 32 plain hex digits. For SHA-1 authentication, the non-encrypted key must be 40 hex - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 383
- Enter the text string used in the encryption algorithm. All neighboring OSPFv3 routers must share the key to decrypt information. Only a non-encrypted key is supported. Required lengths of the non-encrypted key are: 3DES - 48 hex digits; DES - 16 hex digits; AES-CBC - 32 hex digits for AES-128 and - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 384
routers must share the key to decrypt information. Only a non-encrypted key is supported. Required lengths of the non-encrypted key are: 3DES - 48 hex digits; to ping the link-local IPv6 address of adjacent router interface? Troubleshooting OSPFv3 with show Commands • View a summary of all OSPF - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 385
globally on each router. • All OSPFv3 routers in the area must share the same authentication key to exchange information. Only a non- encrypted key is supported. For MD5 authentication, the non-encrypted key must be 32 plain hex digits. For SHA-1 authentication, the non-encrypted key must be 40 hex - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 386
must first delete the authentication policy. • All OSPFv3 routers in the area must share the same encryption key to decrypt information. Only a nonencrypted key is supported. Required lengths of the non-encrypted key are: 3DES - 48 hex digits; DES - 16 hex digits; AES-CBC - 32 hex digits for AES-128 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 387
command disables the distribution of default route. Example OS10(config)# router ospfv3 100 OS10(config-router-ospfv3-100)# default-information originate always Supported Releases 10.3.0E or later ipv6 ospf area Attaches an interface to an OSPF area. Syntax ipv6 ospf process-id area area-id - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 388
command removes an interface from an OSPFv3 area. OS10(config)# interface vlan 10 OS10(conf-if-vl-10)# ipv6 ospf 10 area 1 Supported Releases 10.3.0E or later ipv6 ospf authentication Configures OSPFv3 authentication on an IPv6 interface. Syntax ipv6 ospf authentication {null | ipsec spi number - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 389
no version of this command removes the IPv6 OSPF cost configuration. OS10(config)# interface vlan 10 OS10(conf-if-vl-10)# ipv6 ospf cost 10 Supported Releases 10.3.0E or later ipv6 ospf dead-interval Sets the time interval since the last hello-packet was received from a router. After the interval - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 390
of the this command resets the value to the default. OS10(config)# interface vlan 10 OS10(conf-if-vl-10)# ipv6 ospf hello-interval 30 Supported Releases 10.3.0E or later ipv6 ospf network Sets the network type for the interface. Syntax ipv6 ospf network {point-to-point | broadcast} Parameters - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 391
of the this command disables the Passive interface configuration. Example OS10(config)# interface ethernet 1/1/6 OS10(conf-if-eth1/1/6)# ipv6 ospf passive Supported Releases 10.3.0E or later ipv6 ospf priority Sets the priority of the interface to determine the designated router for the OSPFv3 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 392
(config-router-ospfv3-100)# redistribute bgp 4 route-map dell1 Example (Connected) OS10((config-router-ospfv3-100)# redistribute connected route-map dell2 Supported Releases 10.3.0E or later router-id Configures a fixed router ID for the OSPFv3 process. Syntax router-id ip-address Parameters - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 393
this command disables the router ID configuration. OS10(config)# router ospfv3 10 OS10(config-router-ospfv3-100)# router-id 10.10.1.5 Supported Releases 10.3.0E or later router ospfv3 Enters Router OSPFv3 mode and configures an OSPFv3 instance. Syntax router ospfv3 instance-number Parameters - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 394
/1/1 2.2.2.2 1369 0x8000011B 5 ethernet1/1/1 10.0.0.2 1044 0x80000001 5 ethernet1/1/1 Type-5 AS External Link States ADV Router Age Seq# Prefix 3.3.3.3 3116 0x80000126 400::/64 3.3.3.3 3116 0x80000124 34::/64 Supported Releases 10.3.0E or later 394 Layer 3 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 395
configured, Hello 10, Dead 40, Wait 40, Retransmit 5 Neighbor Count is 1, Adjacent neighbor count is 1 Adjacent with neighbor 2.2.2.2(Designated Router) Supported Releases 10.3.0E or later show ipv6 ospf neighbor Displays a list of OSPFv3 neighbors connected to the local router. Syntax show - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 396
0 hello-tmr-mismatch 0 dead-ivl-mismatch 0 options-mismatch 0 nbr-admin-down 0 own-hello-drop 0 self-orig 0 wrong-length 0 version-mismatch 0 area-mismatch 0 Supported Releases 10.4.0E(R1) or later timers spf (OSPFv3) Enables shortest path first (SPF) throttling to delay an SPF calculation when - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 397
msec Number of area in this router is 1, normal 1 stub 0 nssa Area (0.0.0.1) Number of interface in this area is 1 SPF algorithm executed 2 times Supported Releases 10.4.0E(R1) or later Object tracking manager Object tracking manager (OTM) allows you to track the link status of Layer 2 interfaces - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 398
Figure 3. Object tracking Interface tracking You can create an object that tracks the line-protocol state of a Layer 2 interface, and monitors its operational status (Up or Down). You can configure up to 500 objects. Each object is assigned a unique ID. The no version of this command deletes the - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 399
• Loopback - Loopback interface identifier • mgmt - Management interface 1 Configure object tracking in CONFIGURATION mode from 1 to 500. track object-id 2 (Optional) Enter the interface object tracking on the line-protocol state of a Layer 2 interface in OBJECT TRACKING mode. interface interface - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 400
in communicating a state change is specified in seconds. Object tracking As a client, VRRP can track up to 20 interface objects plus 12 tracked interfaces supported for each VRRP group. You can assign a unique priority-cost value from 1 to 254 to each tracked VRRP object or group interface. The - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 401
up to 180). Defaults Not configured Command Mode CONFIGURATION Usage Information None Example OS10(conf-track-100)# delay up 200 down 100 Supported Releases 10.3.0E or later interface line-protocol Configures an object to track a specific interface's line-protocol status. Syntax Parameters - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 402
- Enter the IPv4 host address. Not configured CONFIGURATION None OS10(config)# track 100 OS10(conf-track-100)# ip 10.10.10.1 reachability Supported Releases 10.3.0E or later ipv6 reachability Configures an object to track a specific next-hop host's reachability. Syntax ipv6 host-ip-address - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 403
2017-02-03T08:41:25Z1 2 ipv4-reachablity 1.1.1.1 DOWN 2017-02-03T08:41:43Z1 3 ipv6-reachablity 10::10 DOWN 2017-02-03T08:41:55Z1 Supported Releases 10.3.0E or later track Configures and manages tracked objects. Syntax track object-id Parameters object-id - Enter the object ID to track - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 404
Policy-based routing Policy-based routing (PBR) provides a mechanism to redirect IPv4 and IPv6 data packets based on the policies defined to override the switch's forwarding decisions based on the routing table. Policy-based route-maps A route-map is an ordered set of rules that control the - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 405
Apply match parameters to IPv4 route-map OS10(conf-route-map)# route-map map1 OS10(conf-route-map)# match ip address acl5 Apply match and set parameters to IPv6 route-map OS10(conf-route-map)# route-map map1 OS10(conf-route-map)# match ipv6 address acl8 OS10(conf-route-map)# set ipv6 next-hop 20::20 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 406
] name-Enter the name of an access-list (up to 140 characters). Not configured ROUTE-MAP None OS10(conf-route-map)# match ip address acl1 Supported Releases 10.3.0E or later policy route-map Assigns a route-map for IPv4 or IPV6 policy-based routing to the interface. Syntax {ip | ipv6} policy - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 407
IPv6 address. Defaults Not configured Command Mode ROUTE-MAP Usage Information None Example OS10(conf-route-map)# set ip next-hop 10.10.10.10 Supported Releases 10.3.0E or later set next-hop track Sets the next-hop IPv4 or IPv6 address to track the PBR object. Syntax Parameters set - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 408
does not flow across VRs. VRF allows multiple instances of routing tables to co-exist within the same router at the same time. OS 10 supports a management VRF instance and a default VRF instance. You can add management ports to the management VRF instance. All the front panel ports and logical - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 409
in the either of the management or default VRF instances. Refer to the following table for the services supported in the management VRF instance and the default VRF instance. Table 3. Services supported Application COPP ACL DHCP client DHCP relay DHCP server DNS client FTP client HTTP client ICMP - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 410
no version of this command removes the domain list configuration from the management VRF instance. OS10(config)# ip domain-list vrf management dns1 dell.com Supported Releases 10.4.0E(R1) or later ip domain-name vrf Configures a domain name for the management VRF instance. Syntax ip domain-name - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 411
configured CONFIGURATION The no version of this command removes the host name from the management VRF instance. OS10(config)# ip host vrf management dell 10.1.1.1 Supported Releases 10.4.0E(R1) or later ip http vrf Configures an HTTP client for the management VRF instance. Syntax ip http vrf - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 412
The no version of this command removes management VRF instance configuration from the SCP client. Example OS10(config)# ip scp vrf management Supported Releases 10.4.0E(R1) or later ip sftp vrf Configures an SFTP client for the management VRF instance. Syntax Parameters Default Command - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 413
configuration from the TFTP client. OS10(config)# ip tftp vrf management Supported Releases 10.4.0E(R1) or later ip vrf management Configures the Information None Example OS10# show hosts vrf management Default Domain Name : dell.com Domain List : abc.com xyz.net Name Servers : 10.16 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 414
OS10# show ip vrf VRF-Name default Interfaces Mgmt1/1/1 Eth1/1/1-1/1/2 Vlan1 management OS10# show ip vrf management VRF-Name Interfaces management Supported Releases 10.4.0E(R1) or later Virtual router redundancy protocol VRRP allows you to form virtual routers from groups of physical - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 415
to transmit packets destined to the Internet. Router B receives and forwards packets on interface ethernet 1/1/5. Until Router A resumes operation, VRRP allows Router B to provide uninterrupted service to the users on the LAN segment accessing the Internet. Layer 3 415 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 416
Create virtual router VRRP uses the VRID to identify each virtual router configured. Before using VRRP, you must configure the interface with the primary IP address and enable it. • Create a virtual router for the interface with the VRRP identifier in INTERFACE mode (1 to 255). vrrp-group vrrp-id • - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 417
configured on the interface. Though a single VRRP group can contain virtual IP addresses belonging to multiple IP subnets configured on the interface, Dell EMC recommends configuring virtual IP addresses belonging to the same IP subnet for any one VRRP group. An interface on which you enable VRRP - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 418
interface ethernet1/1/2 switchport access vlan 1 no shutdown ! interface ethernet1/1/3 switchport access vlan 1 no shutdown ! interface ethernet1/1/4 switchport access vlan 1 --more-View VRRP information When the VRRP process completes initialization, the State field contains either master or - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 419
with the same password or authentication is disabled. Authentication for VRRPv3 is not supported. 1 Create a virtual router for the interface with the VRRP identifier in group 1 OS10(conf-eth1/1/1-vrid-1)# authentication simple-text dell Disable preempt Prevent the Backup router with the higher - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 420
change at Sep 24 07:17:45 2016 ! debug radius false snmp-server contact http://www.dell.com/support/softwarecontacts snmp-server location "United States" username admin password $6$q9QBeYjZ$jfxzVqGhkxX3smxJSH9DDz7/3OJc6m5wjF8nnLD7/VKx8SloIhp4NoGZs0I/ UNwh8WVuxwfd9q4pWIgNs5BKH. aaa authentication - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 421
ethernet1/1/2 switchport access vlan 1 no shutdown Interface/object tracking You can monitor the state of any interface according to the virtual group. OS10 supports a maximum of 10 track groups and each track group can track a maximum of five interfaces. If the tracked interface goes down, the - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 422
interface vlan1 no shutdown ! interface mgmt1/1/1 no shutdown ! support-assist ! track 10 track-interface ethernet1/1/1 VRRP commands ). Default Command Mode Usage Information 1 second or 100 centisecs INTERFACE-VRRP Dell EMC recommends keeping the default setting for this command. If you do - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 423
if the original Master recovers or the new Master fails. The no version of this command disables preemption. OS10(conf-eth1/1/5-vrid-254)# preempt Supported Releases 10.2.0E or later priority Assigns a VRRP priority value for the VRRP group. The VRRP protocol uses this value during the master - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 424
an error message. The no version of this command resets the value to the default (100). OS10(conf-eth1/1/5-vrid-254)# priority 200 Supported Releases 10.2.0E or later show vrrp Displays VRRP group information. Syntax show vrrp {brief | vrrp-id | ipv6 group-id} Parameters • brief - Displays - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 425
value to the default. OS10(conf-eth1/1/5-vrid-254)# track 400 Example (Priority Cost) OS10(conf-eth1/1/5-vrid-254)# track 400 priority-cost 20 Supported Releases 10.2.0E or later track interface Monitors an interface and lowers the priority value of the VRRP group on that interface, if disabled - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 426
the VRRP configured interfaces. The no version of this command resets the value to the default. Example OS10(config)# vrrp delay reload 5 Supported Releases 10.4.0E(R1) or later vrrp-group Assigns a VRRP group identification number to an IPv4 interface or VLAN Syntax Parameters Default Command - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 427
vrrp-ipv6-group configuration. OS10(conf-if-eth1/1/7)# vrrp-ipv6-group 250 Supported Releases 10.2.0E or later vrrp version Sets the VRRP protocol version for 3} Parameters • 2 - Set to VRRP version 2. • both - Allows in-service migration from VRRP version 2 to VRRP version 3. • 3 - Set to VRRP - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 428
A switch in a Layer 2 network may require a larger MAC address table size, while a switch in a Layer 3 network may require a larger routing table size. OS10 supports several UFT modes for the forwarding tables. By default, OS10 selects a UFT mode which provides a reasonable size for all tables. The - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 429
of the network environment. You need to reload the switch to apply the changes. OS10(config)# hardware forwarding-table mode scaled-l3-hosts Supported Releases 10.3.0E or later show hardware forwarding-table mode Displays the current hardware forwarding table mode, and the mode after the next - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 430
-mode L2 MAC Entries : 163840 L3 Host Entries : 147456 L3 Route Entries : 16384 Next-boot Settings scaled-l3-hosts 98304 212992 98304 Supported Releases 10.3.0E or later show hardware forwarding-table mode all Displays table sizes for the available hardware forwarding table modes. Syntax - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 431
7 System management Dynamic host configuration protocol Provides information to dynamically assign IP addresses and other configuration parameters to network hosts based on policies (see DHCP commands). Network time protocol Provides information about how to synchronize timekeeping between time - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 432
The table shows common options using DHCP packet formats. Subnet mask 1 - Client's subnet mask Router 3 - Router IP addresses that serve as the client's default gateway Domain name server 6 - Domain name servers (DNS) that are available to the client Domain name 15 - Domain name that clients - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 433
the network. The DHCP access service minimizes the overhead required to add means you do not have to manually create and maintain IP address Dell OS10(conf-dhcp-Dell)# network 20.1.1.0/24 Show running configuration OS10(conf-dhcp-Dell)# do show running-configuration ... ! ip dhcp server ! pool Dell - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 434
24 hours). OS10(config)# ip dhcp server OS10(conf-dhcp)# pool Dell OS10(conf-dhcp-Dell)# lease 36 Default gateway Ensure the IP address of the default router is resolution - domain name server (DNS) or NetBIOS Windows internet naming service (WINS). Both DHCP and WINS clients query IP servers to - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 435
type Configure NetBIOS WINS address resolution OS10(config)# ip dhcp server OS10(conf-dhcp)# pool Dell OS10(conf-dhcp-Dell)# netbios-name-server 192.168.10.5 OS10(conf-dhcp-Dell)# netbios-node-type Hybrid Manual binding entries Address binding is mapping between the IP address and the media access - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 436
. aaa authentication system:local ip domain-name dell.com ip domain-list f10.com ip name-server 1.1.1.1 2::2 ip host dell-f10.com 10.10.10.10 snmp-server community public read-only snmp-server contact http://www.dell.com/support/ snmp-server location United States debug radius - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 437
this command enables the DHCP server. OS10(conf-dhcp)# no disable Supported Releases 10.2.0E or later dns-server address Assigns a DNS server ...address8] Parameters • address - Enter the DNS server IP address that services clients on the subnet in A.B.C.D or A::B format. • address2...address8 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 438
of this command removes the configuration. Example OS10(conf-dhcp-Dell)# domain-name dell.com Supported Releases 10.2.0E or later hardware-address Configures the client hardware address for manual configurations. Syntax Parameters Default Command Mode Usage Information Example hardware - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 439
Example OS10(conf-dhcp-Dell)# host 20.1.1.100 Supported Releases 10.2.0E or later ip dhcp server 20.1.1.1 Example (IPv6) OS10(conf-if-eth1/1/22)# ip helper-address 00:01:e8:8c:4d:0a Supported Releases 10.2.0E or later lease Configures a lease time for the IP addresses in a pool. Syntax - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 440
DHCP client, in order of preference. The no version of this command returns the value to the default. OS10(conf-dhcp-Dell)# netbios-name-server 192.168.10.5 Supported Releases 10.2.0E or later netbios-node-type Configures the NetBIOS node type for the DHCP client. Syntax Parameters netbios-node - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 441
Command Mode CONFIGURATION Usage Information Use this command to create an IP address pool name. Example OS10(conf-dhcp)# pool Dell OS10(conf-dhcp-Dell)# Supported Releases 10.2.0E or later show ip dhcp binding Displays the DHCP binding table with IPv4 addresses. Syntax show ip dhcp - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 442
to incomplete DNS requests. The no version of this command returns the value to the default. Example OS10(config)# ip domain-name jay dell.com Supported Releases 10.2.0E or later ip host Configures mapping between the host name server and the IP address. Syntax Parameters ip host [host-name - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 443
address table uses this mapping information to resolve host names. The no version of this command disables the mapping. OS10(config)# ip host dell 1.1.1.1 Supported Releases 10.2.0E or later ip name-server Configures up to a three IPv4 or IPv6 addresses used for network name servers. Syntax ip - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 444
dell-pc1 20.1.1.1 Supported Releases 10.2.0E or later Network time protocol NTP synchronizes best time from several other clocks, updates the local clock, and estimates its accuracy. NOTE: OS10 supports both NTP server and client roles. Enable NTP NTP is disabled by default. To enable NTP, - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 445
View system clock state OS10(config)# do show ntp status system peer: 0.0.0.0 system peer mode: unspec leap indicator: 11 stratum: 16 precision: -22 root distance: 0.00000 s root dispersion: 1.28647 s reference ID: [73.78.73.84] reference time: 00000000.00000000 Mon, Jan system - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 446
an IPv4 address in A.B.C.D format. • ipv6-address - Enter an IPv6 address in nnnn:nnnn:nnnn:nnnn:nnnn:nnnn:nnnn:nnnn format (elision of zeros is supported). • key keyid - Enter a text string as the key exchanged between the NTP server and the client. • prefer - Enter the keyword to set this NTP - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 447
the ntp trusted-key command. Use the ntp authenticate command to enable NTP authentication. OS10(config)# ntp authentication-key 1200 md5 0 dell Supported Releases 10.2.0E or later ntp broadcast client Configures the interface to receive NTP broadcasts from an NTP server. Syntax Parameters ntp - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 448
None Disabled CONFIGURATION The no version of this command disables NTP for the management VRF instance. OS10(config)# ntp enable vrf management Supported Releases 10.4.0E(R1) or later ntp master Configures an NTP master server. Syntax ntp master stratum Parameters stratum - Enter the stratum - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 449
To determine which server to select, use the show ntp associations command. Dell EMC recommends limiting the number of hosts you configure, as many polls can impact network performance. OS10(config)# ntp server eureka.com Supported Releases 10.2.0E or later ntp source Configures an interface IP - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 450
-key command, you must also change this command. The no version of this command removes the key. OS10(config)# ntp trusted-key 234567 Supported Releases 10.2.0E or later show ntp associations Displays the NTP master and peers. Syntax Parameters Default Command Mode Usage Information show ntp - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 451
16000.0 OS10# show ntp associations vrf management remote local st poll reach delay offset disp *1.1.1.2 1.1.1.1 3 64 1 0.00027 0.000056 0.43309 Supported Releases 10.2.0E or later show ntp status Displays NTP configuration information. Syntax Parameters Default Command Mode Usage - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 452
System clock OS10 uses the network time protocol (NTP) to synchronize the system clock with a time-serving host. If you do not use NTP, set the system time and the timezone. The hardware-based real-clock time (RTC) is reset to the new system time. You can set the current time and date after you - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 453
time (RTC) resets to the new time. The new system clock setting is applied immediately. OS10# clock set 18:30:10 2017-01-25 Supported Releases 10.2.1E or later clock timezone Sets the time zone used for the system clock. Syntax clock timezone timezone-string Hours Minutes Parameters • Enter - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 454
configured Command Mode CONFIGURATION Usage Information The no version of this command disables the timeout. Example OS10(config)# exec-timeout 300 OS10(config)# Supported Releases 10.3.1E or later kill-session Terminate a user session. Syntax kill-session session-ID 454 System management - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 455
58:39Z 4 snmp_user 57 0 0 0 2017-07-10T23:58:40Z 6 admin 17 0 0 4 2017-07-12T03:55:18Z *7 admin 10 0 0 0 2017-07-12T04:42:55Z OS10# Supported Releases 10.3.1E or later Telnet server To allow Telnet TCP/IP connections to an OS10 switch, enable the Telnet server. The OS10 Telnet - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 456
10.4.0E(R1) or later Security Accounting, authentication, and authorization (AAA) services secure networks against unauthorized access. In addition to local authentication, OS10 supports remote authentication dial-in service (RADIUS) and terminal access controller access control system 456 System - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 457
TACACS+, an OS10 switch acts as a client and sends authentication requests to a server that contains all user authentication and network service access information. A RADIUS or TACACS+ server provides accounting, authentication (user credentials verification), and authorization (user privilege-level - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 458
role, you are authenticated and authorized. You do not need to enter an enable password because you are automatically placed in EXEC mode. OS10 supports the constrained RBAC model. With this model, you can inherit permissions when you create a new user role, restrict or add commands a user can enter - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 459
retransmit attempts allowed on RADIUS servers by using the radius-server retransmit and radius-server timeout commands. By default, OS10 supports three RADIUS authentication attempts and times out after five seconds. • Configure the number of times OS10 retransmits a RADIUS authentication request - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 460
TACACS+ provides greater data security by encrypting the entire protocol portion in a packet sent from the switch to an authentication server. RADIUS encrypts only passwords. • Configure a TACACS+ authentication server in CONFIGURATION mode. By default, a TACACS+ server uses TCP port 49 for - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 461
number of max-auth-tries is reduced by one. In this case, if you configured ip ssh server max-auth-tries 1, the password prompt does not display. Virtual terminal line Virtual terminal line (VTY) is used to control Telnet or SSH connections to the switch. You can enter the VTY mode by using the - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 462
of this command. To reset the authentication method to local, enter the aaa authentication local command. OS10(config)# aaa authentication radius Supported Releases 10.2.0E or later aaa re-authenticate enable Requires user re-authentication after a change in the authentication method or server - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 463
VTY CONFIGURATION The no version of this command removes the filter. OS10(config)# line vty OS10(config-line-vty)# ip access-class deny10 Supported Releases 10.4.0E(R1) or later ipv6 access-class Filters connections based on an IPv6 access list in virtual terminal line. Syntax Parameters Default - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 464
ssh server cipher cipher-list cipher-list - Enter the list of cipher algorithms separated by space. The following is the list of cipher algorithms supported by the SSH server: • 3des-cbc • aes128-cbc • aes192-cbc • aes256-cbc • aes128-ctr • aes192-ctr • aes256-ctr • [email protected] • aes256 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 465
-exchange-algorithm - Enter the list of Key Exchange algorithms separated by space. The following is the list of Key Exchange algorithms supported by the SSH server: • curve25519-sha256 • diffie-hellman-group1-sha1 • diffie-hellman-group14-sha1 • diffie-hellman-group-exchange-sha1 • diffie-hellman - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 466
ip ssh server mac hmac-algorithm hmac-algorithm - Enter the list of HMAC algorithms separated by space. The following is the list of HMAC algorithms supported by the SSH server: • hmac-md5 • hmac-md5-96 • hmac-ripemd160 • hmac-sha1 • hmac-sha1-96 • hmac-sha2-256 • hmac-sha2-512 • umac-64@openssh - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 467
Command Mode CONFIGURATION Usage Information The no version of this command removes the configuration. Example OS10(config)# ip ssh server port 255 Supported Releases 10.3.0E or later ip ssh server pubkey-authentication Enable public key authentication in an SSH server. Syntax ip ssh server - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 468
SSH server to be reachable on the management VRF instance, use the ip ssh server vrf command. OS10(config)# ip ssh server vrf management Supported Releases 10.4.0E(R1) or later line vty Enters the virtual terminal line mode to access the virtual terminal (VTY). Syntax Parameters Default Command - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 469
, at least one option is required. Example OS10(config)# password-attributes min-length 6 character-restriction upper 2 lower 2 numeric 2 Supported Releases 10.4.0E(R1) or later radius-server host Configures a RADIUS authentication server. Syntax Parameters radius-server host {hostname | ip - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 470
on RADIUS servers. The no version of this command resets the value to the default. OS10(config)# radius-server retransmit 50 Supported Releases 10.2.0E or later radius-server timeout Configures the timeout used to resend RADIUS authentication requests. Syntax radius-server timeout seconds - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 471
CONFIGURATION The no version of this command removes the RADIUS server from the management VRF instance. OS10(config)# radius-server vrf management Supported Releases 10.4.0E(R1) or later show ip ssh Displays the SSH server information. Syntax show ip ssh Parameters None Default Not - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 472
time period : 0 Successes in time period : 1 Last Login Time : 2017-11-01T15:42:07Z Last Login Location : 1001:10:16:210::4001 Supported Releases 10.4.0E(R1) or later show users Displays information for all users logged into OS10. Syntax Parameters Default Command Mode Usage Information - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 473
users Index Line User Role Application Idle Location Login-Time Lock 1 ttyS0 admin sysadmin login/clish . - 2016-04-29 01:02:00 Supported Releases 10.2.0E or later tacacs-server host Configures a TACACS+ server for user authentication. Syntax tacacs-server host {hostname | ip-address - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 474
passwords entered in MD-5, SHA-256, and SHA-512 format are supported. • To increase the required password strength, use the password-attributes Example OS10(config)# username user05 password newpwd404 role sysadmin Supported Releases 10.2.0E or later Simple network management protocol Network - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 475
of this command removes access to a community. OS10(config)# snmp-server community public ro Supported Releases 10.2.0E or later snmp-server contact Configures contact information for troubleshooting this SNMP node. Syntax snmp-server contact text Parameters text - Enter an alphanumeric text - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 476
startup-configuration 2 Backup the startup configuration in EXEC mode. copy config://startup.xml config:// 3 Download the new software image from dell.com/support, extract the bin files from the tar file, and save the file in EXEC mode. image download file-url 4 (Optional) View the - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 477
OS Version: 10.4.0E(R2) Build Version: 10.4.0E(R2.27) Build Time: 2018-01-23T15:14:48-0800 System Type: S4248FBL-ON Architecture: x86_64 Up Time: 00:55:09 Boot system partition Set the boot partition to active or standby for subsequent boot cycles. Boot OS10 from standby to load the image on the - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 478
Usage Information Example image cancel None Not configured EXEC This command attempts to cancel an active file download in progress. OS10# image cancel Supported Releases 10.2.0E or later image copy Copies the entire image in the active partition to the standby partition (mirror image). Syntax - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 479
command to view the progress. OS10# image download ftp://[email protected]:/PKGS_OS10-Enterprise-10.4.0E. 55-installer-x86_64.bin Supported Releases 10.2.0E or later image install Installs a new image, either from a previously downloaded file or from a remote location. Syntax Parameters image - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 480
:11:14Z Standby Partition: A Standby SW Version: 10.2.0E Standby Build Date/Time: 2016-10-03T23:11:14Z Next-Boot: active[B] Supported Releases 10.2.0E or later show image status Displays image transfer and installation information. Syntax show image status Parameters None Default Not - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 481
Supported Releases 10.2.0E or later show version Displays software version information. Syntax show version Parameters None Default Not configured Command Mode EXEC Usage Information None Example Supported Releases 10.2.0E or later System management 481 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 482
existing ACL without disrupting traffic flow. Existing entries in the CAM shuffle to accommodate the new entries. Hot-lock ACLs are enabled by default and support ACLs on all platforms. 482 Access Control Lists - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 483
VLAN ID Set in the packet header Class of service Present in the packet header IPv4/IPv6 and per ACL type. IP fragment handling OS10 supports a configurable option to explicitly deny IP fragmented packet size limit. This provides a particular problem for ACL processing. If the ACL filters - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 484
L3 ACL rules Use ACL commands for L3 packet filtering. TCP packets from host 10.1.1.1 with the TCP destination port equal to 24 are permitted, and all others are denied. TCP packets that are first fragments or non-fragmented from host 10.1.1.1 with the TCP destination port equal to 24 are permitted, - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 485
User-provided sequence number • Enter IP ACCESS LIST mode by creating an IP ACL in CONFIGURATION mode. ip access-list access-list-name • Configure a drop or forward filter in IPV4-ACL mode. seq sequence-number {deny | permit | remark} {ip-protocol-number | icmp | ip | protocol | tcp | udp} {source - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 486
Table 7. L2 and L3 targeted traffic L2 ACL / L3 ACL Deny / Deny Deny / Permit Permit / Deny Permit / Permit Targeted traffic L3 ACL denies L3 ACL permits L3 ACL denies L3 ACL permits Assign and apply ACL filters To filter an Ethernet interface, a port-channel interface, or a VLAN, assign an IP - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 487
onto each interface and achieves the same results. You can use an egress ACL filter to restrict egress traffic. For example, when a denial of service (DOS) attack traffic is isolated to a specific interface, apply an egress ACL filter to block the flow from exiting the network and thus protect - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 488
ethernet1/1/29 seq 10 deny ip any any fragment count (100 packets) Clear access-list counters Clear IPv4, IPv6, or MAC access-list counters for a specific access-list or all lists. The counter counts the number of packets that match each permit or deny statement in an access-list. To get a more - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 489
Route-maps Route-maps a series of commands that contain a matching criterion and action. They change the packets meeting the matching criterion. ACLs and prefix-lists can only drop or forward the packet or traffic while route-maps process routes for route redistribution. For example, use a route-map - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 490
View route-map configuration OS10(conf-router-bgp-neighbor-af)# do show route-map route-map test1, deny, sequence 10 Match clauses: ip address prefix-list p1 Set clauses: route-map test2, permit, sequence 10 Match clauses: ip address prefix-list p1 Set clauses: route-map test3, deny, sequence 10 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 491
set weight value Check set conditions OS10(config)# route-map ip permit 1 OS10(conf-route-map)# match metric 2567 continue Clause Only BGP route-maps support the continue clause. When a match is found, set clauses run and the packet is forwarded - no routemap processing occurs. If you configure the - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 492
ACL on the source port or the monitored port, both flow-based monitoring and port mirroring do not function. Flow-based monitoring is supported only for ingress traffic. The show monitor session session-id command displays output which indicates if a particular session is enabled for flowmonitoring - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 493
the counters to start at zero. To view access-list information, use the show access-lists command. OS10# clear ip access-list counters Supported Releases 10.2.0E or later clear ipv6 access-list counters Clears IPv6 access-list counters for a specific access-list. Syntax clear ipv6 access-list - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 494
counters to start at zero. To view access-list information, use the show access-lists command. Example OS10# clear mac access-list counters Supported Releases 10.2.0E or later deny Configures a filter to drop packets with a specific IP address. Syntax deny [protocol-number | icmp | ip | tcp - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 495
The no version of this command removes the filter. OS10(config)# ipv6 access-list ipv6test OS10(conf-ipv6-acl)# deny ipv6 any any capture session 1 Supported Releases 10.2.0E or later deny (MAC) Configures a filter to drop packets with a specific MAC address. Syntax deny {nn:nn:nn:nn:nn:nn [00 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 496
removes the filter. OS10(config)# mac access-list macacl OS10(conf-mac-acl)# deny any any cos 7 OS10(conf-mac-acl)# deny any any vlan 2 Supported Releases 10.2.0E or later deny icmp Configures a filter to drop all or specific internet control message protocol (ICMP) messages. Syntax deny icmp - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 497
. The no version of this command removes the filter. OS10(config)# ipv6 access-list ipv6test OS10(conf-ipv6-acl)# deny icmp any any capture session 1 Supported Releases 10.2.0E or later deny ip Configures a filter to drop all or specific packets from an IPv4 address. Syntax Parameters deny ip - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 498
of this command removes the filter. OS10(config)# ip access-list testflow OS10(conf-ipv4-acl)# deny ip any any capture session 1 count Supported Releases 10.2.0E or later deny ipv6 Configures a filter to drop all or specific packets from an IPv6 address. Syntax deny ipv6 [A::B | A::B/x | any - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 499
version of this command removes the filter. OS10(config)# ip access-list testflow OS10(conf-ipv4-acl)# deny tcp any any capture session 1 Supported Releases 10.2.0E or later deny tcp (IPv6) Configures a filter that drops TCP IPv6 packets meeting the filter criteria. Syntax Parameters deny tcp - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 500
version of this command removes the filter. OS10(config)# ipv6 access-list ipv6test OS10(conf-ipv6-acl)# deny tcp any any capture session 1 Supported Releases 10.2.0E or later deny udp Configures a filter to drop user datagram protocol (UDP) packets meeting the filter criteria. Syntax Parameters - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 501
. The no version of this command removes the filter. OS10(config)# ip access-list testflow OS10(conf-ipv4-acl)# deny udp any any capture session 1 Supported Releases 10.2.0E or later deny udp (IPv6) Configures a filter to drop UDP IPv6 packets that match filter criteria. Syntax deny udp - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 502
-ACL, IPV6-ACL, MAC-ACL Usage Information The no version of this command deletes the ACL description. Example OS10(conf-ipv4-acl)# description ipacltest Supported Releases 10.2.0E or later ip access-group Assigns an IP access group to an interface. Syntax ip access-group access-list-name {in - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 503
it a special meaning. (space) Match space character. _ (underscore) Match space, comma, brackets, start and end of a string. Workaround None; not supported in OS10. None; not supported in OS10. Use [[:punct:]] or "," (comma). The space between AS numbers in an AS path is expressed present using - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 504
Not configured CONFIGURATION The no version of this command removes the community list. OS10(config)# ip community-list standard STD_LIST deny local-AS Supported Release 10.3.0E or later ip community-list standard permit Creates a standard community list for BGP to permit access. Syntax ip - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 505
version of this command removes the extended community list. OS10(config)# ip extcommunity-list standard STD_LIST permit 4byteas-generic transitive 1.65412:60 Supported Release 10.3.0E or later ip prefix-list description Configures a description of an IP prefix list. Syntax ip prefix-list name - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 506
The no version of this command removes the specified prefix-list. OS10(config)# ip prefix-list denyprefix deny 10.10.10.2/16 le 30 Supported Release 10.3.0E or later ip prefix-list permit Creates a prefix-list to permit route filtering from a specified network address. Syntax ip prefix-list - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 507
no version of this command removes the specified prefix list. OS10(config)# ip prefix-list seqprefix seq 65535 deny 10.10.10.1/16 ge 10 Supported Release 10.3.0E or later ip prefix-list seq permit Configures a filter to permit route filtering from a specified prefix list. Syntax Parameters ipv6 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 508
Not configured INTERFACE The no version of this command deletes an IPv6 ACL configuration. OS10(conf-if-eth1/1/8)# ipv6 access-group test6 in Supported Releases 10.2.0E or later ipv6 access-list Creates an IP access list to filter based on an IPv6 address. Syntax Parameters Default Command - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 509
no version of this command removes the specified prefix list. OS10(config)# ipv6 prefix-list TEST deny AB10::1/128 ge 10 le 30 Supported Release 10.3.0E or later ipv6 prefix-list description Configures a description of an IPv6 prefix-list. Syntax ipv6 prefix-list name description Parameters - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 510
The no version of this command removes the specified prefix-list. OS10(config)# ipv6 prefix-list TEST seq 65535 deny AB20::1/128 ge 10 Supported Release 10.3.0E or later ipv6 prefix-list seq permit Configures a filter to permit route filtering from a specified prefix-list. Syntax ipv6 prefix - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 511
configured CONFIGURATION The no version of this command resets the value to the default. OS10(config)# mac access-group maclist in OS10(conf-mac-acl)# Supported Releases 10.2.0E or later mac access-list Creates a MAC access list to filter based on an MAC address. Syntax mac access-list access - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 512
of this command removes the filter. OS10(config)# ip access-list testflow OS10(conf-ipv4-acl)# permit udp any any capture session 1 Supported Releases 10.2.0E or later permit (IPv6) Configures a filter to allow packets with a specific IPv6 address. Syntax permit [protocol-number | icmp | ipv6 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 513
:11:11:11:11 any cos 7 OS10(conf-mac-acl)# permit 00:00:00:00:11:11 00:00:11:11:11:11 any vlan 2 Supported Releases 10.2.0E or later permit icmp Configures a filter to permit all or specific internet control message protocol (ICMP) messages. Syntax permit icmp [A.B.C.D | A.B.C.D/x | any | host - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 514
of this command removes the filter. OS10(config)# ip access-list testflow OS10(conf-ipv4-acl)# permit icmp any any capture session 1 Supported Releases 10.2.0E or later permit icmp (IPv6) Configures a filter to permit all or specific ICMP messages. Syntax permit icmp [A::B | A::B/x | any | host - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 515
, only bytes increment. The no version of this command removes the filter. OS10(conf-ipv4-acl)# permit ip any any capture session 1 Supported Releases 10.2.0E or later permit ipv6 Configures a filter to permit all or specific packets from an IPv6 address. Syntax permit ipv6 [A::B | A::B/x | any - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 516
bytes increment. The no version of this command removes the filter. OS10(conf-ipv6-acl)# permit ipv6 any any count capture session 1 Supported Releases 10.2.0E or later permit tcp Configures a filter to permit TCP packets meeting the filter criteria. Syntax permit tcp [A.B.C.D | A.B.C.D/x | any - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 517
no version of this command removes the filter. OS10(config)# ipv6 access-list ipv6test OS10(conf-ipv6-acl)# permit tcp any any capture session 1 Supported Releases 10.2.0E or later permit udp Configures a filter that allows UDP packets meeting the filter criteria. Syntax Parameters permit udp - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 518
of this command removes the filter. OS10(config)# ip access-list testflow OS10(conf-ipv4-acl)# permit udp any any capture session 1 Supported Releases 10.2.0E or later permit udp (IPv6) Configures a filter to permit UDP packets meeting the filter criteria. Syntax permit udp [A::B | A::B/x | any - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 519
, IPv6, or MAC. OS10(conf-ipv4-acl)# remark 10 Deny rest of the traffic OS10(conf-ipv4-acl)# remark 5 Permit traffic from XYZ Inc. Supported Releases 10.2.0E or later seq deny Assigns a sequence number to deny IP addresses while creating the filter. Syntax Parameters seq sequence-number deny - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 520
know the filter's sequence number. OS10(config)# ip access-list testflow OS10(conf-ipv4-acl)# seq 10 deny tcp any any capture session 1 Supported Releases 10.2.0E or later seq deny (IPv6) Assigns a sequence number to deny IPv6 addresses while creating the filter. Syntax seq sequence-number deny - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 521
you know the filter's sequence number. OS10(config)# ipv6 access-list ipv6test OS10(conf-ipv6-acl)# seq 5 deny ipv6 any any capture session 1 count Supported Releases 10.2.0E or later seq deny (MAC) Assigns a sequence number to a deny filter in a MAC access list while creating the filter. Syntax - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 522
if you know the filter's sequence number. OS10(config)# ip access-list egress OS10(conf-ipv4-acl)# seq 5 deny icmp any any capture session 1 Supported Releases 10.2.0E or later seq deny icmp (IPv6) Assigns a sequence number to deny ICMP messages while creating the filter. Syntax Parameters seq - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 523
know the filter's sequence number. OS10(config)# ipv6 access-list ipv6test OS10(conf-ipv6-acl)# seq 10 deny icmp any any capture session 1 Supported Releases 10.2.0E or later seq deny ip Assigns a sequence number to deny IP addresses while creating the filter. Syntax seq sequence-number deny - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 524
know the filter's sequence number. OS10(config)# ipv6 access-list ipv6test OS10(conf-ipv6-acl)# seq 10 deny ipv6 any any capture session 1 Supported Releases 10.2.0E or later seq deny tcp Assigns a filter to deny TCP packets while creating the filter. Syntax Parameters seq sequence-number deny - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 525
you know the filter's sequence number. OS10(config)# ip access-list egress OS10(conf-ipv4-acl)# seq 10 deny tcp any any capture session 1 Supported Releases 10.2.0E or later seq deny tcp (IPv6) Assigns a filter to deny TCP packets while creating the filter. Syntax Parameters seq sequence-number - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 526
if you know the filter's sequence number. OS10(config)# ipv6 access-list ipv6test OS10(conf-ipv6-acl)# seq 10 deny tcp any any capture session 1 Supported Releases 10.2.0E or later seq deny udp Assigns a filter to deny UDP packets while creating the filter. Syntax seq sequence-number deny udp - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 527
you know the filter's sequence number. OS10(config)# ip access-list egress OS10(conf-ipv4-acl)# seq 10 deny udp any any capture session 1 Supported Releases 10.2.0E or later seq deny udp (IPv6) Assigns a filter to deny UDP packets while creating the filter. Syntax Parameters seq sequence-number - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 528
the filter's sequence number. OS10(config)# ipv6 access-list ipv6test OS10(conf-ipv6-acl)# seq 10 deny udp any any capture session 1 Supported Releases 10.2.0E or later seq permit Assigns a sequence number to permit packets while creating the filter. Syntax seq sequence-number permit [protocol - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 529
know the filter's sequence number. OS10(config)# ipv6 access-list ipv6test OS10(conf-ipv6-acl)# seq 10 permit ipv6 any any capture session 1 Supported Releases 10.2.0E or later seq permit (MAC) Assigns a sequence number to permit MAC addresses while creating a filter. Syntax seq sequence-number - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 530
:11:11 any cos 7 OS10(conf-mac-acl)# seq 20 permit 00:00:00:00:11:11 00:00:11:11:11:11 any vlan 2 Supported Releases 10.2.0E or later seq permit icmp Assigns a sequence number to allow ICMP messages while creating the filter Syntax seq sequence-number permit icmp - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 531
you know the filter's sequence number. OS10(config)# ipv6 access-list ipv6test OS10(conf-ipv6-acl)# seq 5 permit icmp any any capture session 1 Supported Releases 10.2.0E or later seq permit ip Assigns a sequence number to allow packets while creating the filter. Syntax Parameters seq sequence - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 532
you know the filter's sequence number. OS10(config)# ip access-list egress OS10(conf-ipv4-acl)# seq 5 permit ip any any capture session 1 Supported Releases 10.2.0E or later seq permit ipv6 Assigns a sequence number to allow packets while creating the filter. Syntax seq sequence-number permit - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 533
command if you know the filter's sequence number. OS10(config)# ip access-list egress OS10(conf-ipv4-acl)# seq 5 permit tcp any any capture session 1 Supported Releases 10.2.0E or later Access Control Lists 533 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 534
command if you know the filter's sequence number. OS10(config)# ipv6 access-list egress OS10(conf-ipv6-acl)# seq 5 permit tcp any any capture session 1 Supported Releases 10.2.0E or later 534 Access Control Lists - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 535
command if you know the filter's sequence number. OS10(config)# ip access-list egress OS10(conf-ipv4-acl)# seq 5 permit udp any any capture session 1 Supported Releases 10.2.0E or later Access Control Lists 535 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 536
command if you know the filter's sequence number. OS10(config)# ipv6 access-list egress OS10(conf-ipv6-acl)# seq 5 permit udp any any capture session 1 Supported Releases 10.2.0E or later 536 Access Control Lists - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 537
access-group ccc Ingress IPV6 access list aaa on ethernet 3/0 Ingress IPV6 access list aaa on ethernet 4/0 Egress IPV6 access list aaa on ethernet 4/0 Supported Releases 10.2.0E or later show access-lists Displays IP, MAC, or IPv6 access-list information. Syntax Parameters show {ip | mac | ipv6 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 538
interfaces : ethernet 3/0 ethernet 3/1 seq 10 permit any any Egress IPV6 access list ggg Active on interfaces : ethernet 3/0 seq 5 permit ipv6 11::/32 any count (0 packets) Supported Releases 10.2.0E or later 538 Access Control Lists - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 539
Command Mode EXEC Usage Information None Example OS10# show ip as-path-access-list ip as-path access-list hello permit 123 deny 35 Supported Releases 10.3.0E or later show ip community-list Displays the configured IP community lists in alphabetic order. Syntax Parameters Defaults Command Mode - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 540
24 seq 20 permit 3.4.4.5/32 Example (IPv6) OS10# show ipv6 prefix-list ipv6 prefix-list hello: seq 10 permit 1::1/64 seq 20 deny 2::2/64 Supported Releases 10.3.0E or later Route-map commands continue Configures the next sequence of the route map. Syntax Parameters Default Command Mode Usage - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 541
no version of this command deletes a match AS path filter. Example OS10(config)# route-map bgp OS10(conf-route-map)# match as-path pathtest1 Supported Releases 10.3.0E or later match community Configures a filter to match routes that have a certain COMMUNITY attribute in their BGP path. Syntax - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 542
configured ROUTE-MAP The no version of this command deletes the match. OS10(conf-route-map)# match interface ethernet 1/1/1 OS10(conf-if-eth1/1/1)# Supported Releases 10.2.0E or later match ip address Configures a filter to match routes based on IP addresses specified in IP prefix lists. Syntax - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 543
bgp OS10(conf-route-map)# match ip next-hop prefix-list test100 Supported Releases 10.3.0E or later match ipv6 address Configures a filter to (config)# route-map bgp OS10(conf-route-map)# match ipv6 address test100 Supported Releases 10.3.0E or later match ipv6 next-hop Configures a filter to - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 544
Not configured ROUTE-MAP The no version of this command deletes the match. OS10(config)# route-map bgp OS10(conf-route-map)# match origin egp Supported Releases 10.3.0E or later match route-type Configures a filter to match routes based on how the route is defined. Syntax match route-type - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 545
Command Mode ROUTE-MAP Usage Information The no version of this command deletes the match. Example OS10(conf-route-map)# match tag 656442 Supported Releases 10.2.0E or later route-map Enables a route-map statement and configures its action and sequence number. Syntax Parameters route-map map - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 546
command to delete a community list from a matching route. Example OS10(config)# route-map bgp OS10(conf-route-map)# set comm-list comlist1 add Supported Releases 10.4.0E(R1) or later set comm-list delete Remove communities in the specified list from the COMMUNITY attribute in a matching inbound - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 547
The no version of this command deletes a BGP COMMUNITY attribute assignment. OS10(config)# route-map bgp OS10(conf-route-map)# set community none Supported Releases 10.3.0E or later set extcomm-list add Add communities in the specified list to the EXT COMMUNITY attribute in a matching inbound or - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 548
command deletes the set clause from a route map. OS10(config)# route-map bgp OS10(conf-route-map)# set extcommunity rt 10.10.10.2:325 Supported Releases 10.3.0E or later set local-preference Sets the preference value for the AS path. Syntax set local-preference value Parameters value - Enter - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 549
no version of this command removes the filter. OS10(conf-route-map)# set metric 10 Example (Relative) OS10(conf-route-map)# set metric -25 Supported Releases 10.2.0E or later set metric-type Set the metric type for the a redistributed routel. Syntax set metric-type {type-1 | type-2 | external - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 550
. Example OS10(conf-route-map)# set ip next-hop 10.10.10.2 Example (IPv6) OS10(conf-route-map)# set ipv6 next-hop 11AA:22CC::9 Supported Releases 10.2.0E or later set origin Set the origin of the advertised route. Syntax set origin {egp | igp | incomplete} Parameters • egp - Enter to - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 551
MAP Usage Information The no version of the command deletes the set clause from the route map. Example OS10(conf-route-map)# set weight 200 Supported Releases 10.2.0E or later show route-map Displays the current route map configurations. Syntax show route-map [map-name] Parameters map-name - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 552
precedence over less critical application traffic. QoS enables to prioritize different types of traffic and ensures the required level of quality of service. You can control the following parameters of selected traffic flows: Delay, Bandwidth, Jitter, and Drop. The different QoS features control the - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 553
-plane mode. • The qos and network-qos policies must be applied in the input direction on physical interfaces or on system-qos mode. Quality of service 553 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 554
to classify traffic in a pre-defined way without using any network processor resources. Trust based classification OS10 supports classification based on the 802.1p CoS field (L2) or DSCP field (L3). 802.1p CoS trust trust dot1p-map dot1p-trust-map OS10(config-tmap-dot1p-map)# 554 Quality of service - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 555
12-15 16-19 20-23 24-27 28-31 32-35 36-39 40-43 44-47 48-51 TC id 0 0 1 1 2 2 3 3 4 4 5 5 6 Color G Y G Y G Y G Y G Y G Y G Quality of service 555 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 556
)# policy-map trust 2 Refer pre-defined reserved class-map class-trust in the policy-map. OS10(config-pmap-qos)# class class-trust 556 Quality of service - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 557
OS10(conf-if-eth1/1/1)# service-policy input type qos trust • System-qos level OS10(config-sys-qos)# service-policy input type qos trust match not cos 3,4 • VLAN ID (range of or comma separated VLAN match is not supported) OS10(config-cmap-qos)# match vlan 100 • IP DSCP OS10(config-cmap-qos)# match - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 558
(config-pmap-qos)# class cmap-cos5 OS10(config-pmap-c-qos)# set qos-group 7 • Attach the policy-map to interface. OS10(conf-if-eth1/1/1)# service-policy input type qos cos-trust Control-plane policing Control-plane policing (CoPP) increases security on the system by protecting the route processor - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 559
. To enforce rate-limiting or rate policing on control-plane traffic, create policy maps. You can use the control-plane command to attach the CoPP service policies directly to the control-plane. The default rate limits apply to 12 CPU queues and the protocols mapped to each CPU queue. The control - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 560
-policy(control-plane) input: copp1 Class-map (control-plane): copp set qos-group 2 police cir 100 bc 100 pir 100 be 100 Assign service-policy Controlling traffic and rate the protocol CPU queues requires configuring QoS policies. To enable CoPP, you need to apply the defined policy-map to - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 561
View CMAP1 configuration OS10# show class-map type control-plane cmap1 Class-map (control-plane): cmap1 (match-any) View CoPP service-policy OS10# show policy-map type control-plane Service-policy(control-plane) input: pmap1 Class-map (control-plane): cmap1 set qos-group 6 police cir 200 bc 100 pir - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 562
the traffic rate is above the configured peak-rate, the traffic is dropped to guarantee a bandwidth limit for an ingress traffic flow. 562 Quality of service - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 563
a QoS type policy-map to color the traffic flow. OS10(config)# policy-map ect-color OS10(config-pmap-qos)# class cmap-dscp-3-ect Quality of service 563 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 564
. exit 4 Create a policy-map of type queuing and configure a policy-map name in CONFIGURATION mode. policy-map type queuing policy-map-name 564 Quality of service - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 565
do show class-map Class-map (queuing): solar (match-any) Match: qos-group 5 View policy-map OS10(conf-pmap-c-que)# do show policy-map Service-policy (queuing) output: solar Class-map (queuing): lunar bandwidth percent 80 Strict priority queuing OS10 uses queues for egress QoS policy-types. You can - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 566
pmap-c-que)# exit OS10(conf-pmap-queuing)# exit OS10(config)# system qos OS10(conf-sys-qos)# service-policy output solar View QoS system OS10(conf-sys-qos)# do show qos system Service-policy (output)(queuing): solar Enable strict priority on interface OS10(config)# interface ethernet 1/1/5 OS10(conf - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 567
for the speed of 10G, 25G, 40G, 50G, and 100G. The supported speed varies for different platforms. The following table lists the maximum buffer size 18KB 91KB 9KB 9KB 100G NA 36KB 142KB 9KB 9KB NOTE: The supported speed varies for different platforms. After the reserved buffers are utilized, each - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 568
colors in the WRED CONFIGURATION mode. OS10(config-wred)# random-detect color yellow minimum-threshold 100 maximum-threshold 300 drop-probability 40 568 Quality of service - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 569
interface ethernet 1/1/1 OS10(conf-if-eth1/1/1)# random-detect wred_prof_1 7 Enable WRED/ECN on a service-pool. OS10(config)# system qos OS10(config-sys-qos)# random-detect pool 0 wred_prof_1 Storm OS10(conf-pmap-que)# bandwidth percent 70 Supported Releases 10.2.0E or later Quality of service 569 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 570
policy-map type is trust, where the class type must be qos. Example OS10(conf-pmap-qos)# class c1 Supported Releases 10.2.0E or later class-map Creates a QoS class-map which filters traffic to match packets to the c1 OS10(conf-cmap-qos)# Command History 10.2.0E or later 570 Quality of service - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 571
Default Not configured Command Mode EXEC Usage Information None Example OS10# clear qos statistics Supported Releases 10.2.0E or later clear qos statistics type Clears all queue counters, including for qos, queuing, or control-plane. Default Not configured Quality of service 571 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 572
Example (policymap) OS10(config)# policy-map type control-plane p1 OS10(conf-pmap-control-plane)# Supported Releases 10.2.0E or later flowcontrol Enables or disables link-level flow control on an interface. no version of this command returns the value to the default. 572 Quality of service - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 573
, the access-list ignores the permit and deny keywords. OS10(conf-cmap-qos)# match ip access-group name ag1 Supported Releases 10.2.0E or later match cos Matches a cost of service (CoS) value to L2 dot1p packets. Syntax Parameters match [not] cos cos-value • cos-value - Enter a CoS value (0 to - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 574
the second statement overwrites the first statement. The match-all option in a class-map does not support ip-any. Select either ip or IPv6 for the match-all criteria. If you select ip-any, . OS10(conf-cmap-qos)# match not ipv6 precedence 3 Supported Releases 10.2.0E or later 574 Quality of service - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 575
the second statement overwrites the first statement. OS10(conf-cmap-qos)# match vlan 100 Supported Releases 10.2.0E or later mtu Calculates the buffer size allocation for matched flows. Syntax Example OS10(conf-pmap-nqos-c)# mtu 2500 Supported Releases 10.3.0E or later Quality of service 575 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 576
network-qos nqclass1 OS10(conf-cmap-nqos-c)# pause buffer-size 45 pause-threshold 30 resumethreshold 10 Supported Releases 10.3.0E or later pfc-cos Configures priority flow-control for cost of service (CoS). Syntax pfc-cos cos-value Parameters cos-value - Enter a single, comma-delimited, or - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 577
removes the maximum buffer size limit. OS10(config-sys-qos)# pfc-max-buffer-size 2000 Supported Releases 10.4.0E(R1) or later pfc-shared-buffer-size Changes the shared buffers size limit (conf-sys-qos)# pfc-shared-buffer-size 2000 Supported Releases 10.3.0E or later Quality of service 577 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 578
default. OS10(conf-sys-qos)# pfc-shared-headroom-buffer-size 2000 Supported Releases 10.4.0E(R1) or later police Configures traffic policing on values are taken as the pir values. Only the ingress QoS policy type supports this command. For control-plane policing, the rate values are in pps. OS10 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 579
map p1 Example (Queuing) OS10(config)# policy-map type queuing p1 Supported Releases 10.2.0E or later priority Sets the scheduler as a strict-priority Only the egress QoS policy type supports this command. Example OS10(conf-pmap-que)# priority Supported Releases 10.2.0E or later priority-flow - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 580
this command returns the value to the default. OS10(conf-tmap-dot1p-qos)# qos-group 5 dot1p 5 Supported Releases 10.3.0E or later qos-group dscp Configures a dscp trust map to the traffic class. Syntax range of dscp values (0 to 63). Default Command Mode 0 TRUST-MAP 580 Quality of service - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 581
command returns the value to the default. OS10(conf-tmap-dscp-qos)# qos-group 5 dscp 42 Supported Releases 10.3.0E or later queue-limit Configures static or dynamic shared buffer thresholds. Syntax queue-limit { type queuing pmap1 OS10(config-pmap-queuing)# class cmap1 Quality of service 581 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 582
)# queue-limit thresh-mode static 50 Supported Releases 10.3.0E or later queue bandwidth removes the bandwidth from the queue. Example Supported Releases 10.4.0E(R1) or later queue qos tmap-tc-queue-qos)# queue 2 qos-group 5 Supported Releases 10.3.0E or later random-detect (interface) Assigns - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 583
(config-pmap-queuing)# class c1 OS10(config-pmap-c-que)# random-detect test_wred Supported Releases 10.4.0E(R1) or later random-detect color Configures the threshold of minimum-threshold 100 maximumthreshold 300 drop-probability 40 Supported Releases 10.4.0E(R1) or later Quality of service 583 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 584
from the interface. OS10(config)# system qos OS10(config-sys-qos)# random-detect pool 0 test_wred Supported Releases 10.4.0E(R1) or later random-detect weight Configures the exponential weight value used to calculate wred test_wred OS10(config-wred)# random-detect weight 10 584 Quality of service - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 585
-level, the interface-level policy takes precedence over the system-level policy. OS10(conf-if-eth1/1/7)# service-policy input type qos p1 Supported Releases 10.2.0E or later set cos Sets a cost of service (CoS) value to mark L2 802.1p (dot1p) packets. Syntax set cos cos-value Parameters cos - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 586
policy type only supports this command. pmap-c-qos)# set dscp 10 Supported Releases 10.2.0E or later control-plane ingress QoS policy type only supports this command. When class-map type is 7. OS10(conf-pmap-c-qos)# set qos-group 7 Supported Releases 10.2.0E or later shape Shapes the outgoing - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 587
CLASS-MAP Only the ingress QoS policy type supports this command. You must enter both the pmap-c-que)# shape min kbps 11 max kbps 44 Supported Releases 10.2.0E or later show class-map Displays match-all) Match(not): ip-any dscp 10 Supported Releases 10.2.0E or later show control-plane info - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 588
Not configured EXEC Monitors statistics for the control-plane and to troubleshoot CoPP. OS10# show control-plane info Queue Rate Limit(in pps 600 IPV6_OSPF IPV4_BGP IPV4_OSPF 10 600 IPV6_DHCP IPV4_DHCP SERVICEABILITY 11 300 OPEN_FLOW Supported Releases 10.2.0E or later show control-plane - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 589
: 100 pps multicast-storm-control : 200 pps broadcast-storm-control : Disabled flow-control-rx: Enabled flow-control-tx: Disabled Service-policy (Input)(qos): p1 Supported Releases 10.2.0E or later show policy-map Displays information on all existing policy-maps. Syntax show policy-map type - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 590
Not configured Command Mode EXEC Usage Information Monitors statistics for the control-plane and troubleshoots CoPP. Example OS10# show qos control-plane Service-policy (Input): p1 Supported Releases 10.2.0E or later show qos egress bufffers interface Displays egress buffer configurations - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 591
6 lossy 1664 dynamic 8 7 lossy 1664 dynamic 8 Supported Releases 10.3.0E or later show egress buffer-stats interface 3 0 0 0 0 4 0 0 0 0 5 0 0 0 0 6 0 0 0 0 7 0 0 0 0 OS10# Supported Releases 10.3.0E or later show qos ingress buffers interface Displays interface - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 592
- - 0 STATIC 0 0 0 4 - - 0 STATIC 0 0 0 5 - - 0 STATIC 0 0 0 6 - - 0 STATIC 0 0 0 7 - 0-2,5-7 8 STATIC 0 0 0 Supported Releases 10.3.0E or later show ingress buffer-stats 681824 35984 1 0 0 0 2 0 0 0 3 0 0 0 4 0 0 0 592 Quality of service - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 593
Mode Usage Information Example show qos system None Not configured EXEC View and verify system-level service-policy configuration information. OS10# show qos system Service-policy (Input) (qos) : policy1 Service-policy (Output)(queuing) : policy2 Supported Releases 10.2.0E or later Quality of - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 594
896 Total lossy buffers - 8178 Total shared lossy buffers - 5938 Total used shared lossy buffers - 0 Supported Releases 10.3.0E or later show qos maps Displays the active system trust map. Syntax show qos maps Map: queue-map1 Queue Traffic-Class 1 5 2 6 594 Quality of service - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 595
0 0-7 1 8-15 2 16-23 3 24-31 4 32-39 5 40-47 6 48-55 7 56-63 Default Traffic-Class to Queue Map Traffic-Class Queue number Quality of service 595 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 596
| Yellow MIN MAX DROP-RATE| MIN MAX DROP-RATE| MIN MAX D KB KB %| KB KB %| KB KB Supported Releases system qos Enters SYSTEM-QOS mode to configure system-level service policies. Syntax Parameters Default Command Mode system qos None Not configured SYSTEM-QOS 596 Quality of - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 597
qos OS10(config-sys-qos)# Supported Releases 10.2.0E or later trust and class-trust support this command. OS10(conf-pmap-c-qos)# trust dot1p Supported Releases 10.3.0E OS10(config-tmap-dot1p-map)# qos-group 4 dot1p 5 Supported Releases 10.3.0E or later trust dscp-map Creates user-defined - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 598
no version of this command returns the value to the default. OS10(config)# trust dscp-map dscp-trust1 Supported Releases 10.3.0E or later qos-map traffic-class Creates user-defined trust map for queue mapping. Syntax qos of this command returns the value to the default. 598 Quality of service - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 599
interface ethernet 1/1/1 OS10(conf-if-eth1/1/1)# trust-map dscp dscp-trustmap1 Supported Releases 10.3.0E or later wred Configures a weighted random early detection ( WRED profile. OS10(config)# wred test_wred OS10(config-wred)# Supported Releases 10.4.0E(R1) or later Quality of service 599 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 600
role of spanning tree protocols (STPs) by allowing link aggregation group (LAG) terminations on two separate distribution or core switches and supporting a loop-free topology. • Allows a single device to use a LAG across two upstream devices • Provides a loop-free topology • Eliminates STP-blocked - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 601
to the attached devices. It is also associated with the configuration mode that you must use to assign VLT global parameters. • A VLT domain supports two node members. These peer devices appear as a single logical device to network access devices that connect to VLT ports through a port-channel - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 602
, the VLTi does not activate. • In a VLT domain, VLT peers support connections to network devices that connect to only one peer. VLT interconnect A roles in the VLT domain are automatically assigned. 4 (Optional) Manually reconfigure the default VLT MAC address. Configure the VLT MAC address in - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 603
RSTP configuration RSTP mode is supported on VLT ports. Before you configure VLT on peer switches, configure RSTP in the network. RSTP prevents loops during the VLT startup phase. • Enable RSTP - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 604
RPVST+ configuration RPVST+ mode is supported on VLT ports. Before you configure VLT on peer switches, configure RPVST+ in the network. You can use RPVST+ for initial loop prevention during the - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 605
1 Configure a VLT domain and enter VLT-DOMAIN mode. Configure the same VLT domain ID on each peer, from 1 to 255. vlt-domain domain-id 2 Repeat the steps on the VLT peer to create the VLT domain. Peer 1 OS10(config)# vlt-domain 1 OS10(conf-vlt-1)# Peer 2 OS10(config)# vlt-domain 1 OS10(conf-vlt-1)# - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 606
routing VLT unicast routing enables optimized routing where packets destined for the L3 endpoint of the VLT peer are locally routed. VLT unicast routing is supported for IPv4 and IPv6. To enable VLT unicast routing, both VLT peers must be in L3 mode. The VLAN configuration must be symmetrical on - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 607
show running-configuration interface vlan 10 ! interface vlan10 no shutdown no vrrp mode active-active OS10# Migrate VMs across data centers OS10 does not support proxy gateway. Instead of proxy gateway, use VRRP in VLANs to migrate virtual machines across data centers. You must assign the same VRRP - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 608
• Server racks, Rack 1 and Rack 2, are part of data centers DC1 and DC2, respectively. • Rack 1 is connected to devices A1 and B1 in L2 network segment. • Rack 2 is connected to devices A2 and B2 in L2 network segment. • A VLT LAG is present between A1 and B1 as well as A2 and B2. • A1 and B1 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 609
• Configure VLT port channel for VLAN 100: D1(config)# interface port-channel 10 D1(conf-if-po-10)# vlt-port-channel 10 D1(conf-if-po-10)# switchport mode trunk D1(conf-if-po-10)# switchport trunk allowed vlan 100 D1(conf-if-po-10)# exit • Add members to port channel 10: D1(config)# interface - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 610
C2(conf-if-po-20)# switchport trunk allowed vlan 200 C2(conf-if-po-20)# exit • Add members to port channel 20: C2(config)# interface ethernet 1/1/5 C2(conf-if-eth1/1/5)# channel-group 20 C2(conf-if-eth1/1/5)# exit C2(config)# interface ethernet 1/1/6 C2(conf-if-eth1/1/6)# channel-group 20 C2(conf-if - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 611
• View detailed information about VLT ports in EXEC mode. show vlt domain-id vlt-port-detail • View the current configuration of all VLT domains in EXEC mode. show running-configuration vlt View peer-routing information OS10# show vlt 1 Domain ID : 1 Unit ID : 1 Role : primary Version : 1.0 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 612
* 1 - 2 4 VLT VLAN mismatch: VLT ID : 1 VLT Unit ID Mismatch VLAN List * 1 1 2 2 VLT ID : 2 VLT Unit ID Mismatch VLAN List * 1 1 2 2 View VLT port details * indicates the local peer OS10# show vlt 1 vlt-port-detail VLT port channel ID : 1 VLT Unit ID Port-Channel Status - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 613
)# vlt-domain 1 OS10(conf-vlt-1)# backup destination ipv6 1::1 vrf management Supported Releases 10.3.1E or later delay-restore Configures a time interval to delay Command Mode VLT-DOMAIN Usage Information The VLT node discovery service auto-LAGs the discovery ports and creates VLTi interfaces. - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 614
Usage Information Example peer-routing None Disabled VLT-DOMAIN The no version of this command disables L3 routing. OS10(conf-vlt-1)# peer-routing Supported Releases 10.2.0E or later peer-routing-timeout Configures the delay after which peer routing is disabled when the peer is not available - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 615
designated path cost: 0 Number of transitions to forwarding state: 1 Edge port: No (default) Link Type: Point-to-Point BPDU Sent: 101, Received: 21 Supported Releases 10.3.0E or later show vlt Displays information on a VLT domain. Syntax Parameter Default show vlt id id - Enter a VLT domain ID - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 616
: up VLT Peer Unit ID System MAC Address Status IP Address Version 2 90:b1:1c:f4:bc:0a up fda5:74c8:b79e:1::2 1.0 Supported Releases 10.2.0E or later show vlt backup-link Displays the details of heartbeat status. Syntax Parameters Default Command Mode Usage Information Example show vlt - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 617
137 ---------MAC 00:00:00:00:00:02 is missing from Node(s) 2 Run "show vlt d1 mismatch ..." commands to identify configuration issues Supported Releases 10.2.0E or later show vlt mismatch Displays mismatches in a VLT domain configuration. Syntax show vlt id mismatch [peer-routing | vlan | vlt - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 618
) OS10# show vlt 1 mismatch vlt-vlan VLT ID : 1 VLT Unit ID Mismatch VLAN List * 1 1 2 2 VLT ID : 2 VLT Unit ID Mismatch VLAN List * 1 1 2 2 Supported Releases 10.2.0E or later show vlt role Displays the VLT role of the local peer. Syntax show vlt id role Parameters id - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 619
occurs on VLT peers, the VLTi link between peers does not activate. The no version of this command disables VLT. OS10(config)# vlt-domain 1 Supported Releases 10.2.0E or later vlt-port-channel Configures the ID used to map interfaces on VLT peers into a single VLT port-channel. Syntax vlt- - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 620
1 Example (peer 2) OS10(conf-if-po-20)# vlt-port-channel 1 Supported Releases 10.2.0E or later vlt-mac Configures a MAC address for all peer switches . Example OS10(conf-vlt-1)# vlt-mac 00:00:00:00:00:02 Supported Releases 10.2.0E or later vrrp mode active-active Enables the VRRP peers to - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 621
11 Converged data center services OS10 supports converged data center services, including IEEE 802.1 data center bridging (DCB from a transmitting device. The 802.1p priority is also known as the class of service (CoS) or dot1p priority value. When PFC detects congestion of a dot1p traffic class, - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 622
supported for 802.1p priority traffic (dot1p 0 to 7). FCoE traffic traditionally uses dot1p priority 3 - iSCSI storage traffic uses dot1p priority 4. • Configure PFC for ingress traffic by using network-qos class and policy maps (see Quality of Service class-trust class instructs OS10 interfaces to - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 623
the qos trust policy to ingress traffic in SYSTEM-QOS or INTERFACE mode. service-policy input type qos trust-policy-map-name Configure a non-default dot1p Tx PFC frames: 0 Cos Rx Tx 0 0 0 1 0 0 2 0 0 3 0 0 4 0 0 5 0 0 6 0 0 7 0 0 Converged data center services 623 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 624
notes to change the default settings. Configuration steps: 1 Create PFC dot1p traffic classes. 2 Configure ingress buffers for PFC traffic. 3 Apply a service policy and enable PFC. 4 (Optional) Configure the PFC shared buffer for lossless traffic. Create PFC dot1p traffic classes 1 Create a network - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 625
pmap-c-qos)# class-map class-trust OS10(config-pmap-c-qos)# trust dot1p OS10(config-pmap-c-qos)# exit OS10(config)# system qos OS10(config-sys-qos)# service-policy input type qos pclass1 OS10(config-sys-qos)# exit OS10(config)# class-map type network-qos cc1 OS10(config-cmap-nqos)# match qos-group - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 626
Interface : ethernet1/1/15 Speed : 10G Priority Used reserved Used shared Used HDRM Group buffers buffers buffers 0 9360 681824 35984 1 0 0 0 2 0 0 0 3 0 0 0 4 0 0 0 5 0 0 0 6 0 0 0 7 0 0 0 PFC commands 626 Converged data center services - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 627
class cc1 OS10(conf-pmap-c-nqos)# pause buffer-size 30 pause-threshold 20 resumethreshold 10 Supported Releases 10.3.0E or later pfc-cos Configures the matching dot1p values used to send PFC hyphen-separated range, or multiple dot1p values separated by commas. Converged data center services 627 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 628
type network-qos pp1 OS10(conf-pmap-network-qos)# class cc1 OS10(conf-pmap-c-nqos)# pfc-cos 3 Supported Releases 10.3.0E or later pfc-shared-buffer-size Configures the amount of shared buffers available for PFC-enabled you want to use. You cannot enable PFC 628 Converged data center services - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 629
qos policy-class map applied to the interface. OS10(conf-if-eth1/1/1)# priority-flow-control mode on Supported Releases 10.3.0E or later queue-limit Sets the static and dynamic thresholds used to limit the Total Rx PFC Frames: 0 Total Tx PFC frames: 587236 Converged data center services 629 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 630
group to rate-limit best-effort LAN traffic. ETS configuration notes • ETS is supported on L2 802.1p priority (dot1p 0 to 7) and L3 DSCP (0 to traffic classes to lossless queues. - Ingress trust policy - Configure a service policy to trust dot1p values in ingress traffic. - Egress queuing policy - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 631
from DCBX TLVs. • The CEE/IEEE2.5 versions of ETS TLVs are supported. ETS configurations are received in a TLV from a peer. Configure ETS traffic-class queue-map-name queue {0-7} qos-group {0-7} exit 3 Create a service policy for the class-trust class in CONFIGURATION mode. Enter POLICY-CLASS-MAP - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 632
-policy input type qos trust-policy-map-name 8 Apply the queuing policy to egress traffic in SYSTEM-QOS or INTERFACE mode. service-policy output type queuing policy-map-name 9 Enable ETS globally in SYSTEM-QOS mode or on an interface/interface range in INTERFACE mode. ets mode - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 633
The no version of this command disables ETS. Example OS10(config-sys-qos)# ets mode on Supported Releases 10.3.0E or later Data center bridging eXchange DCBX allows a switch to automatically discover and ) switches are part of a fibre channel storage network. Converged data center services 633 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 634
in topologies that support lossless operation for FCoE OS10 interfaces. You can manually reconfigure DCBX settings on both levels. • OS10 supports DCBX versions: CEE and port operates in a manual role by default. The support interface levels. You can manually reconfigure DCBX settings or disable - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 635
for iSCSI disabled Interface ethernet1/1/15 Port Role is Manual DCBX Operational Status is Enabled Is Configuration Source? ErPfI Local DCBX Status DCBX Operational Version is 0 DCBX Max Version Supported is 0 Sequence Number: 14 Acknowledgment Number: 5 Protocol State: center services 635 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 636
OS10# show lldp dcbx interface ethernet 1/1/15 ets detail Interface ethernet1/1/15 Max Supported PG is 8 Number of Traffic Classes is 8 Admin mode is on Admin Parameters 7 0% SP 15 0% SP Remote Willing Status is disabled Local Parameters Local is enabled 636 Converged data center services - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 637
ensure consistent operation of peers in a converged data center network. OS10(config)# dcbx enable Supported Releases 10.3.0E or later dcbx tlv-select Configures the DCB TLVs advertised by a DCBX- - Advertise ETS recommendation TLVs. • pfc - Advertise PFC TLVs. Converged data center services 637 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 638
. OS10(conf-if-eth1/1/2)# dcbx tlv-select ets-conf pfc Supported Releases 10.3.0E or later dcbx version Configures the DCBX version used OS10(conf-if-eth1/1/2)# dcbx version cee Supported Releases 10.3.0E or later lldp tlv-select Supported Releases 10.3.0E or later 638 Converged data center - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 639
Priority for iSCSI disabled Interface ethernet1/1/15 Port Role is Manual DCBX Operational Status is Enabled Is Configuration Source? FALSE ) OS10# show lldp dcbx interface ethernet 1/1/15 ets Interface ethernet1/1/15 Max Supported PG is 8 Number of Traffic Classes is 8 Admin mode is on detail - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 640
pkts, 2 Output TLV pkts, 0 Error pkts 5 Input Appln Priority TLV pkts, 2 Output Appln Priority TLV pkts, 0 Error Appln Priority TLV Pkts 640 Converged data center services - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 641
Dell EqualLogic storage arrays directly attached to switch ports. To support storage arrays where auto-detection is not supported, manually information and iSCSI session information. • A user-configured iSCSI class of service (CoS) profile is applied to all iSCSI traffic. Classifier rules are used - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 642
Dell EqualLogic storage arrays directly connected to an interface. iSCSI automatically configures switch parameters after connection to a storage device is verified. You must manually enable an interface to support ingress iSCSI flows. Apply the service policy to ingress interfaces in CONFIGURATION - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 643
config-pmap-c-app)# set cos 4 OS10 (config-pmap-c-app)# exit OS10(config-pmap-application)# exit OS10(config)# system qos OS10(config-sys-qos)# service-policy type application policy-iscsi OS10(config-sys-qos)# exit OS10(config)# iscsi session-monitoring enable OS10(config)# iscsi aging time 15 OS10 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 644
TCP ports before the session closes. The no version of this command disables the aging time. Example OS10(config)# iscsi aging time 30 Supported Releases 10.3.0E or later iscsi enable Enables iSCSI auto-detection of attached storage arrays and switch auto-configuration. Syntax Parameter iscsi - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 645
Command Mode Usage Information Example Enabled on S4048T-ON/S4048-ON; disabled on others CONFIGURATION support LLDP. The no version of this command disables the connection. OS10(conf-if-eth1/1/2)# iscsi profile-storage compellant Supported Releases 10.3.0E or later Converged data center services - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 646
the IP address removes a TCP port from iSCSI monitoring. OS10(config)# iscsi target port 26,40 Supported Releases 10.3.0E or later lldp tlv-select dcbxp-appln iscsi Enables a port to advertise iSCSI application dot1p priority-bitmap configured with the iscsi 646 Converged data center services - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 647
command disables iSCSI TLV transmission. OS10(conf-if-eth1/1/1)# lldp tlv-select dcbxp-appln iscsi Supported Releases 10.3.0E or later show iscsi Displays currently configured iSCSI settings. Syntax show iscsi Parameters 10.10.210 54748 10.10.10.40 3260 1 Converged data center services 647 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 648
Port ID 10.10.10.210 54835 10.10.10.40 3260 1 Supported Releases 10.3.0E or later show iscsi storage-devices Displays information about the iSCSI storage traffic using: • Separate traffic classes for the different service needs of network applications. • PFC flow control to pause data - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 649
config-pmap-qos)# class class-trust OS10(config-pmap-c-qos)# trust dot1p OS10(config-pmap-c-qos)# end 3. PFC configuration (interface) Apply the service policies with dot1p trust and PFC configurations to an interface. OS10(config)# interface ethernet 1/1/53 OS10(conf-if-eth1/1/53)# no shutdown OS10 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 650
-pmap-c-qos)# end 5. ETS configuration (interface and global) Apply the service policies with dot1p trust and ETS configurations to an interface or on all switch interfaces. Only one qos-map traffic-class map is supported on a switch. OS10(config)# interface ethernet 1/1/53 OS10(conf-if-eth1 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 651
Priority for iSCSI disabled Interface ethernet1/1/53 Port Role is Manual DCBX Operational Status is Enabled Is Configuration Source? FALSE Local lldp dcbx interface ethernet 1/1/53 ets detail Interface ethernet1/1/53 Max Supported PG is 8 Number of Traffic Classes is 8 Admin mode is on Admin - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 652
-pmap-c-app)# set qos-group 6 OS10(config-pmap-c-app)# set cos 6 OS10(config-pmap-c-app)# exit OS10(config-pmap-application)# exit 652 Converged data center services - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 653
vlan 1 no shutdown dcbx version cee service-policy input type network-qos test service-policy input type qos pclass service-policy output type queuing pmap1 ets mode for iSCSI disabled Interface ethernet1/1/53 Port Role is Manual DCBX Operational Status is Enabled Is Configuration Source? FALSE - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 654
Sync Peer DCBX Status DCBX Operational Version is 0 DCBX Max Version Supported is 0 Sequence Number: 1 Acknowledgment Number: 2 3 Input PFC ieee service-policy input type network-qos test service-policy input type qos pclass service-policy /1/53 Port Role is Manual DCBX Operational Status is - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 655
traffic monitoring for high-speed networks with many switches and routers. • OS10 supports sFlow version 5 • sFlow collector is supported only on data ports • A maximum of two sFlow collectors • OS10 does not support sFlow on SNMP, VLAN, VRF, tunnel interfaces, extended sFlow, backoff mechanism, and - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 656
sFlow maximum header size OS10(config)# sflow max-header-size 80 View sFlow information OS10# show sflow sFlow services are enabled Management Interface sFlow services are disabled Global default sampling rate: 32768 Global default counter polling interval: 20 Global default extended maximum header - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 657
sFlow polling interval OS10(config)# sflow polling-interval 200 View sFlow information OS10# show sflow sFlow services are enabled Management Interface sFlow services are disabled Global default sampling rate: 32768 Global default counter polling interval: 200 Global default extended maximum - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 658
View sFlow information The current release does not support the statistics for UDP packets dropped. • View sFlow configuration details and statistics in EXEC mode. OS10# show sflow sFlow services are enabled Management Interface sFlow services are disabled Global default sampling rate: 32768 Global - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 659
no version of this command removes the configured sFlow collector. Example OS10(conf)# sflow collector 10.1.1.1 agent-addr 2.2.2.2 6343 max-datagram-size 1500 vrf default Supported Releases 10.3.0E or later sFlow 659 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 660
Use the no version of the command to reset the header size to the default value. OS10(conf)# sflow max-header-size 256 Supported Releases 10.3.0E or later sflow polling-interval Sets the sFlow polling interval. Syntax Parameter sflow polling-interval interval-value interval-value - Enter - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 661
port-channel for the interface type. EXEC OS10 does not support statistics for UDP packets dropped and samples received from the hardware. Example OS10# show sflow sFlow services are enabled Management Interface sFlow services are disabled Global default sampling rate: 32768 Global default counter - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 662
0 UDP packets dropped 34026 sFlow samples collected Example (portchannel) OS10# show sflow interface port-channel 1 port-channel1 sFlow is enabled on port-channel1 Samples rcvd from h/w: 0 Supported Releases 10.3.0E or later 662 sFlow - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 663
OS10 Critical workloads and applications require constant availability. Dell EMC Networking offers tools to help you monitor and troubleshoot problems before they happen. Packet and flow capture Metrics measurement Analysis and reporting Alerting Logging Performance monitoring Mapping and - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 664
-ON-FANTRAY-1 1 S4048T-ON-FANTRAY-2 1 S4048T-ON-FANTRAY-3 1 S4048T-ON-FANTRAY-4 061DJT X01 TW-061DJT-28298-615-0089 061DJT X01 TW-061DJT-28298-615- R 6.1 0.1 0:00.02 top 1 root 20 0 112100 5840 3032 S 0.0 0.1 0:12.32 systemd 2 root 20 0 0 0 0 S 0.0 0.0 0:00.00 kthreadd 664 Troubleshoot OS10 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 665
write captured packets to a file, use the -w parameter. To read the captured file output offline, you can use open source software packages such as wireshark. Troubleshoot OS10 665 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 666
a destination and wait for a response. If there is no response, the destination is not active. The ping command is useful during configuration if you have problems connecting to a hostname or IP address. 666 Troubleshoot OS10 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 667
126) 005.000 ms 001.000 ms 001.000 ms 3 fw-sjc-01.Dell Networking.com (10.11.127.254) 000.000 ms 000.000 ms 000.000 ms 4 www.Dell Networking.com (10.11.84.18) 000.000 ms 000.000 ms 000 :100:201:e8ff:fe00:4c8b, 64 hops max, 60 byte packets Hops Hostname Probe1 Probe2 Probe3 Troubleshoot OS10 667 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 668
: 0 : 1 week 4 days 08:08:17 -- Unit 1 -Status System Identifier Down Reason System Location LED Required Type Current Type Hardware Revision : up : 1 : : off : S4048 : S4048 : 668 Troubleshoot OS10 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 669
. OS10# location-led interface ethernet 1/1/1 on OS10# location-led interface ethernet 1/1/1 off Supported Releases 10.3.0E or later location-led system Changes the location LED of the system. Syntax Enter the system ID. • on | off - Set the system LED to be on or off. Troubleshoot OS10 669 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 670
the specified system ID. OS10# location-led system 1 on OS10# location-led system 1 off Supported Releases 10.3.0E or later ping Tests network connectivity to an IPv4 device. Syntax Parameters ping [ large packets locally. - dont does not set the Don't Fragment (DF) flag. 670 Troubleshoot OS10 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 671
packet you send to diagnose data-related problems in the network (for example, -p to 1500 bytes in decimal or hex) to set quality of service (QoS)-related bits. • -s packetsize - (Optional) Enter 104/0.133/0.025 ms Supported Releases 10.2.0E or in the management VRF instance. Troubleshoot OS10 671 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 672
pad bytes to fill out the packet you send to diagnose data-related problems in the network (for example, -p ff fills the sent packet with all datagrams (up to 1500 bytes in decimal or hex) to set quality of service (QoS)-related bits. • -s packetsize - (Optional) Enter the number of Troubleshoot OS10 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 673
packet loss, time 3005ms rtt min/avg/max/mdev = 2.078/2.194/2.379/0.127 ms Supported Releases 10.2.0E or later show boot Displays boot partition-related information. Syntax show boot [ /Time: 2016-10-03T23:11:14Z Next-Boot: active[B] Supported Releases 10.2.0E or later Troubleshoot OS10 673 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 674
(rev 01) 01:00.1 Ethernet controller: Broadcom Corporation Device b340 (rev 01) Supported Releases 10.2.0E or later show environment Displays information about environmental system components, such as Not configured EXEC None OS10# show environment Unit State Temperature 674 Troubleshoot OS10 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 675
temp sensor 31 1 7 Switch board 3 temp sensor 41 1 8 NPU temp sensor 43 Supported Releases 10.2.0E or later show hash-algorithm Displays hash algorithm information. Syntax show hash-algorithm 226 457 410 1 S4048ON-FANTRAY-3 P1FAN1 A01 CN-123456-FAN10-058-901 Troubleshoot OS10 675 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 676
Supported Releases 10.2.0E or later show processes View process CPU utilization information. Syntax Parameters show processes node RES SHR S %CPU %MEM TIME+ COMMAND 1019 root 20 0 1829416 256080 73508 S 6.6 6.4 1212:36 base_nas OS10# Supported Releases 10.3.0E or later 676 Troubleshoot OS10 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 677
up 3 up NORMAL 1 13085 up 2 13063 up Example (node-id) OS10# show system node-id 1 fanout-configured Interface Breakout capable Breakout state Eth 1/1/1 Yes BREAKOUT_1x1 Troubleshoot OS10 677 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 678
-- FanTray Status AirFlow Fan Speed(rpm) Status 1 up REVERSE 1 13063 up 2 13020 up 2 up REVERSE 1 12956 up 2 12977 up 3 up NORMAL 1 12956 up 2 13063 up Supported Releases 10.2.0E or later 678 Troubleshoot OS10 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 679
16). - -t tos - (Optional) For IPv4, enter the Type of Service (TOS) and Precedence values to use. 16 sets a low delay; 8 Mode Usage Information Example Not configured EXEC None OS10# traceroute www.dell.com traceroute to www.dell.com (23.73.112.54), 30 hops max, 60 byte ms Troubleshoot OS10 679 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 680
, 80 byte packets 1 20::1 (20::1) 2.622 ms 2.649 ms 2.964 ms Supported Releases 10.2.0E or later Password recovery You may need to recover a lost password. system [ 822.344339] reboot: machine restart BIOS (Dell Inc) Boot Selector S6010-ON (SI) 3.20.0.3 (32-port TE/FG) 680 Troubleshoot OS10 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 681
: /dev/mmcblk0 (7832MB) Percent complete: 100% SupportAssist By default, SupportAssist is enabled. SupportAssist sends troubleshooting data securely to Dell Technical Support. SupportAssist does not support automated email notification at the time of hardware fault alert, automatic case creation - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 682
time in SUPPORT-ASSIST mode. do support-assist activity support for your Dell products and services. Dell may use the information for providing recommendations to improve your IT infrastructure. Dell services from Dell. You further agree to allow Dell are further certifying to Dell that you have - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 683
name Eureka OS10(conf-support-assist-Eureka)# contact-person first John last Smith OS10(conf-support-assist-Eureka)# email-address [email protected] OS10(conf-support-assist-Eureka-JohnJamesSmith)# preferred-method email OS10(conf-support-assist-Eureka)# phone primary 408-123-4567 Troubleshoot OS10 683 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 684
support-assist status EULA : Accepted Service : Enabled Contact-Company : DellCMLCAEOS10 Street Address : 7625 Smetana Lane Dr Bldg 7615 Cube F577 City : Minneapolis State : Minnesota Country : USA Zipcode : 55418 Territory : USA Contact-person : Michael Dale Email : abc@dell - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 685
to provide technical support for your Dell products and services. Dell may use the information for providing recommendations to improve your IT infrastructure. Dell SupportAssist also of core dump files. • event-notification - Enables transfer of event notification files. Troubleshoot OS10 685 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 686
for the contact person. Default Command Mode Usage Information Example Not configured SUPPORT-ASSIST The no version of this command removes the configuration. OS10(conf-support-assist-Eureka)# contact-person first "John James" last Smith Supported Releases 10.2.0E or later 686 Troubleshoot OS10 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 687
agreement (EULA). Syntax Parameters eula-consent {support-assist} {accept | reject} • support-assist - Enter to accept or reject the EULA for the service. • accept - Enter to accept the EULA contact method. • phone - Enter to select phone as the preferred contact method. Troubleshoot OS10 687 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 688
.g3.ph.dell.com Command Mode SUPPORT-ASSIST Usage support-assist status command to view the server configuration. The no version of this command removes the remote server. Example OS10(conf-support-assist)# server url https://eureka.com:444 Supported Releases 10.2.0E or later 688 Troubleshoot - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 689
save your contact information (e.g. name, phone number and/or email address) which would be used to provide technical support for your Dell, Inc. products and services. Dell, Inc. may use the information for providing recommendations to improve your IT infrastructure. SupportAssist also collects and - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 690
support-assist status EULA : Accepted Service : Enabled Contact-Company : DellCMLCAEOS10 Street Address : 7625 Smetana Lane Dr Bldg 7615 Cube F577 City : Minneapolis State : Minnesota Country : USA Zipcode : 55418 Territory : USA Contact-person : Michael Dale Email : abc@dell - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 691
company address configuration. Example OS10(conf-support-assist-Eureka)# street-address "One Dell Way" "Suite 100" Supported Releases 10.2.0E or later support-assist-activity Schedules a time to transfer Command Mode Weekly on Sunday at midnight (hour 0 minute 0) EXEC Troubleshoot OS10 691 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 692
that collects Linux system configuration and diagnostics information, as well as show command output to send to Dell Technical Support. To send Dell Technical Support troubleshooting details about the Linux system configuration and OS10 diagnostics, generate an sosreport tar file. 1 Generate the tar - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 693
Support Support support-bundle execution:All Plugin options enabled generate support support-bundle [enable-all-plugin-options] enable-all-plugin-options - (Optional) Generate a full support bundle with all plugin options enabled. None EXEC To send the tar file to Dell Technical Support service - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 694
. no logging server severity • Re-enable any logging command in CONFIGURATION mode. no logging enable Enable server logging for log notice OS10(config)# logging server dell.com severity log-notice View system logs The system log-file contains system event and alarm logs. 694 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 695
OS10# show logging log-file Jun 1 05:01:46 %Node.1-Unit.1:PRI:OS10 %log-notice:ETL_SERVICE_UP: ETL service is up Jun 1 05:02:06 %Node.1-Unit.1:PRI:OS10 %log-notice:EQM_UNIT_DETECTED: Unit pres ent:Unit 1# hardware environment to detect temperature, CPU, and memory utilization. Troubleshoot OS10 695 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 696
alarm). Syntax alarm clear alarm-index Parameters clear alarm-index - Enter the alarm ID to clear the alarm. Default Not configured Command Mode EXEC 696 Troubleshoot OS10 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 697
7 18:36:11 Node.1-Unit.1 Sep 7 18:36:11 Node.1-Unit.1 Supported Releases 10.2.0E or later show alarms details Displays details about active alarms. Syntax Sep 20 0:1:5 Clear-time: New: true State: raised Active-alarm details - 1 Index: 1 Sequence Number: 5 Troubleshoot OS10 697 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 698
Total-count: 0 Critical-count: 0 Major-count: 0 Minor-count: 0 Warning-count: 0 Supported Releases 10.2.0E or later show alarms index Displays information about a specific alarm using the alarm to clear and view alarm details. Example OS10# show alarms index 1 698 Troubleshoot OS10 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 699
time: Sep 20 0:16:52 Clear-time: New: true State: raised Supported Releases 10.2.0E or later show alarms severity Displays all active alarms using critical Type: 1081367 Source: Node.1-Unit.1 Name: EQM_THERMAL_CRIT_CROSSED Description: Raise-time: Sep 20 0:1:5 Troubleshoot OS10 699 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 700
6 Critical-count: 0 Major-count: 2 Minor-count: 2 Warning-count: 2 Supported Releases 10.2.0E or later Logging commands clear logging Clears messages in the logging buffer. to clear the log file [confirm yes/no(default)]: Supported Releases 10.2.0E or later 700 Troubleshoot OS10 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 701
console enable Example (Severity) OS10(config)# logging console severity log-warning Supported Releases 10.2.0E or later logging enable Enables system logging. Syntax logging enable disables all logging. OS10(config)# logging enable Supported Releases 10.2.0E or later Troubleshoot OS10 701 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 702
log-file enable Example (Severity) OS10(config)# logging log-file severity log-notice Supported Releases 10.2.0E or later logging monitor Set the minimum severity level for logging to to warning conditions. • log-notice - Set to normal but significant conditions (default). 702 Troubleshoot OS10 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 703
OS10(config)# logging server dell.com vrf management severity log-debug Supported Releases 10.2.0E or later show logging Displays system logging messages by log-file, process-names, or summary. Syntax show logging {log-file [process-name | line-numbers] | process-names} Troubleshoot OS10 703 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 704
dn_l2_services dn_dot1x dn_l3_core_serv dn_policy dn_qos dn_switch_res_m dn_ospfv3 dn_lacp dn_i3 dn_supportassis --More-- Supported Releases 10.2.0E or later show trace Displays trace messages. Syntax 10:04 OS10 base_nas: [NDI:NDI-SAI], Values are invalid - can't be conv 704 Troubleshoot OS10 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 705
.c:nl_to_nei --More-Supported Releases 10.2.0E or later Log into OS10 device Linux shell access is available for troubleshooting and diagnostic purposes commands to display system state and variables, or as instructed by Dell Support. OS10 login: linuxadmin Password: linuxadmin >> only for - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 706
service contains information about quality of service Guide on the Dell Support page (see dell.com/ support). Hardware What are the default console settings for ON-Series devices? • Set the data rate to 115200 baud • Set the data format to 8 bits, stop bits to 1, and no parity 706 Troubleshoot - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 707
? Use the username commands to add new users. Use the show users command to view a list of current users. How do I view RADIUS transactions to troubleshoot problems? Use the debug radius command. How do I view the current DHCP binding information? Use the show ip dhcp binding command. Layer 2 How do - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 708
view access-list and access-group information? Use the show {ip | mac | ipv6} access-group and show {ip | mac | ipv6} access-list commands. Quality of service What are the QoS error messages? Flow control error messages: • Error: priority-flow-control mode is on, disable pfc mode to enable LLFC 708 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 709
threshold should be greater than equal to Resume threshold. PFC cost of service error messages: • % Error: Not enough buffers are available, to can I check if SupportAssist is enabled? Use the show support-assist status command to view current configuration information. How can Troubleshoot OS10 709 - Dell PowerSwitch S4048T-ON | OS10 Enterprise Edition User Guide Release 10.4.0ER - Page 710
tag or express service code, pull out the luggage tag on the chassis or enter the show chassis command from the CLI. • To receive additional kinds of technical support, click Contact Us, then click Technical Support. To access system documentation, see www.dell.com/manuals/. To search for drivers
OS10 Enterprise Edition User Guide
Release 10.4.0E(R2)