Dell PowerVault MD1220 Interoperability Guide
Dell PowerVault MD1220 Manual
 |
View all Dell PowerVault MD1220 manuals
Add to My Manuals
Save this manual to your list of manuals |
Dell PowerVault MD1220 manual content summary:
- Dell PowerVault MD1220 | Interoperability Guide - Page 1
as an expansion unit behind MD32xx 6Gb/s SAS drives are configured in the MD1200 and MD1220 from Dell's factory, and 3Gb/s SAS drives are supported in the field with the supported MD1200 and MD1220 carriers. Mixing of PowerVault MD1200 and PowerVault MD1220 on the same physical PERC H800 controller - Dell PowerVault MD1220 | Interoperability Guide - Page 2
and PowerVault MD1220 Supported Host Controllers PERC ESG Controller Dell PERC H800 Adapter Dell MD32xx Supported Operating Systems If a PERC H800 is supported in a server then the PowerVault MD1200/1220 is supported on that server. To determine the latest supported operating system perform the - Dell PowerVault MD1220 | Interoperability Guide - Page 3
10K 10K SSD Vendor Seagate Seagate Seagate Seagate Seagate Seagate Seagate Seagate Hitachi Seagate Hitachi Seagate Seagate Seagate Seagate Seagate Fujitsu Hitachi Seagate Fujitsu Hitachi Seagate Fujitsu Hitachi Seagate Hitachi Seagate Pliant PowerVault MD1200 and MD1220 Interoperability Guide l 3 - Dell PowerVault MD1220 | Interoperability Guide - Page 4
latest firmware versions, visit support.dell.com/support/downloads. Table 5. Dell PowerVault MD1200 and MD1220 Minimum Supported Firmware and Software Device Firmware/Software Release Number Version Number Revision MD1200 and MD1220 EMM Firmware R248792 1.01 A00 MD1200 and MD1220 Storage - Dell PowerVault MD1220 | Interoperability Guide - Page 5
MD1200 and MD1220 hardware configurations are supported only on Dell qualified hardware. Figure 1. Dell PowerVault MD1200 and MD1220: Single Enclosure, Unified Mode Figure 2. Dell PowerVault MD1200 and MD1220: Single Enclosure, Split Mode PowerVault MD1200 and MD1220 Interoperability Guide l 5 - Dell PowerVault MD1220 | Interoperability Guide - Page 6
Dell PowerVault MD1200 and MD1220: Maximum Configuration with Enclosure Daisy Chain Expansion Information in this document is subject to change without notice. © 2009-2010 Dell Inc. All rights reserved. Reproduction of these materials in any manner whatsoever without the written permission of Dell
-
1 -
2 -
3 -
4 -
5 -
6
 |
 |
PowerVault MD1200 and MD1220 Interoperability Guide
l
1
Dell™ PowerVault™ MD1200 and PowerVault™
MD1220 Interoperability Guide
This document provides information about the supported hardware and software versions for Dell™
PowerVault™ MD1200 and PowerVault™ MD1220 systems.
NOTE:
The versions specified in this document use the same format as found on
support.dell.com/support/downloads
and may differ from the version information displayed in the
Windows® Device Manager or Dell™ OpenManage™ Server Administrator.
Rules and Considerations
The following are the connectivity and consideration rules for the Dell PowerVault MD1200 and MD1220:
Table 1. Dell PowerVault MD1200 and PowerVault MD1220 Rules and Considerations
PERC H800 is the only host controller supported for PowerVault MD1200 and PowerVault MD1220.
Note: MD1200/1220 is also supported as an expansion unit behind MD32xx
6Gb/s SAS drives are configured in the MD1200 and MD1220 from Dell’s factory, and 3Gb/s SAS drives are supported
in the field with the supported MD1200 and MD1220 carriers.
Mixing of PowerVault MD1200 and PowerVault MD1220 on the same physical PERC H800 controller and in the same
daisy chain is supported. Dell PowerVault MD1120 and PowerVault MD1000 systems cannot coexist on the same
controller as a PowerVault MD1200 or PowerVault MD1220 system.
It is recommended that PowerVault MD1200 and PowerVaultMD1220 be powered up first before the server.
A maximum of four PowerVault MD1200 or PowerVault MD1220 systems can be daisy
‐
chained on each RAID
controller port, for a total of 96 3.5”disk drives on PowerVault MD1200 or 192 2.5”disk drives on PowerVault
MD1220 using the dual
‐
ported PERC H800 controller.
Connecting a PowerVault MD1200 or PowerVault MD1220 to a PowerVault MD3000 or PowerVault MD3000i is not
supported. Connecting to an MD32xx is supported.