Dell S4810P Quick Start Guide

Dell S4810P Manual

Get Dell S4810P PDF manuals and user guides View all Dell S4810P manuals
Add to My Manuals
Save this manual to your list of manuals

Dell S4810P manual content summary:

  • Dell S4810P | Quick Start Guide - Page 1
    Dell Force10 S4810 System Quick Start Guide Regulatory Model: S4810P
  • Dell S4810P | Quick Start Guide - Page 2
  • Dell S4810P | Quick Start Guide - Page 3
    Dell Force10 S4810 System Quick Start Guide Regulatory Model: S4810P
  • Dell S4810P | Quick Start Guide - Page 4
    instructions are not followed. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. If you purchased a Dell n Series computer Dell Inc. is strictly forbidden. Trademarks used in this text: Dell™, the DELL logo, Dell Dell Inc. disclaims any proprietary interest in trademarks
  • Dell S4810P | Quick Start Guide - Page 5
    to the following documents: Documentation S4810 Hardware installation and power-up Installing the S4810 System instructions Software configuration FTOS Configuration Guide for the S4810 System Command line interface FTOS Command Reference for the S4810 System Latest updates FTOS Release
  • Dell S4810P | Quick Start Guide - Page 6
    2 About this Guide
  • Dell S4810P | Quick Start Guide - Page 7
    1 Installing the Hardware This guide assumes all site preparation has been performed before installing the chassis. Installing the S4810 Chassis in a Rack or Cabinet To install the S4810 system, Dell Force10 recommends that you complete the installation procedures in the order presented below.
  • Dell S4810P | Quick Start Guide - Page 8
    outside of the chassis. Power Supply View from chassis I/O side Connect to Rack/Cabinet (ears) Screws View of chassis PSU side Screws Connect to Install chassis into 2-post rack or cabinet Step Task 1 Dell Force10 recommends that one person hold the S4810 chassis in place while a second
  • Dell S4810P | Quick Start Guide - Page 9
    of fault interrupt circuits. Dell Force10 recommends using the shortest end of the ground cable to a suitable ground point. The rack installation ears are not a suitable grounding point. Install the SFP+ QSFP+ Optics The S4810 has 48 SFP+ optical ports and 4 QSFP+ optical ports. For supported
  • Dell S4810P | Quick Start Guide - Page 10
    Points • Splitting a 40G port into 4x10G port is supported only on a standalone unit. • Split ports cannot be used as stack-link to stack an S4810. • Split ports S4810 unit cannot be a part of any stacked system. • The unit number with the split ports must be the default (stack-unit 0). This can be
  • Dell S4810P | Quick Start Guide - Page 11
    is correctly installed. Connect the plug to each AC power connector, making sure that the power cord is secure. As soon as the cable is connected between the S4810 and the power source, the chassis is powered-up; there is no on/off switch. DC Power Connect the plug to each DC receptacle, making sure
  • Dell S4810P | Quick Start Guide - Page 12
    -up; there is no on/off switch. Fans The S4810 comes from the factory with 1 power supply and 2 fan modules installed in the chassis. Both the fan module and the integrated fan-power supply are hot-swappable if a second (redundant) power supply is installed and running. NOTE: Both slots must have
  • Dell S4810P | Quick Start Guide - Page 13
    feet (3,048 meters) 10 to 85% non-condensing MIL-STD-810 AC Power Requirements Parameter Nominal Input Voltage Maximum AC Power Supply Input Current Maximum System Power Input Specifications 100 to 240 VAC, 47-63 Hz 4.20 A @ 100VAC 1.70 A @ 240 VAC 350 W DC Power Requirements Parameter Nominal
  • Dell S4810P | Quick Start Guide - Page 14
    to RETURN and connect the BLACK to -48V. Power Supply 0 (PSU0) is on the left; Power Supply 1(PSU1) is on the right. The power supply modules should slide into the slots smoothly. Do not force a module into a slot. This may damage the power supply or the S4810 chassis. 10 Installing the Hardware
  • Dell S4810P | Quick Start Guide - Page 15
    bay. 3 Tighten the securing screw on the side of the PSU. 4 Attach power cables. 5 The system powers up as soon as the cables are connected between the power supply and the power source. DC Power Supply PSU0 Fan Modules Cable Connector PSU1 Grab Handle Installing the Hardware 11
  • Dell S4810P | Quick Start Guide - Page 16
    12 Installing the Hardware
  • Dell S4810P | Quick Start Guide - Page 17
    Step Task 1 Install an RJ-45 copper cable into the console port. Use a rollover cable to connect the S4810 console port to a terminal server. 2 Connect the other end of the cable to the DTE terminal server. 3 Default terminal settings on the console port are set as follows: 9600 baud rate No parity
  • Dell S4810P | Quick Start Guide - Page 18
    of FTOS is pre-loaded onto the chassis, however the system is not configured when you power up for the first time (except for the default host name, which is Force10). You must configure the system using the CLI. Configure Layer 2 (Data Link) Mode Use the switchport command in INTERFACE mode to
  • Dell S4810P | Quick Start Guide - Page 19
    The S4810 has a dedicated management port and a management routing table that is separate from the IP routing table. Step Task 1 Configure an IP address for the management port. 2 Configure a management route with a default gateway. 3 Configure a username and password. Configure the Management Port
  • Dell S4810P | Quick Start Guide - Page 20
    through the management port. Task Command Syntax Configure a management route ip-address/mask management route to gateway the network from which you are accessing the system. Command Mode CONFIGURATION Configure a Username and Password Configure a system username and password to access the
  • Dell S4810P | Quick Start Guide - Page 21
    encryption method. Dell Force10 recommends using the enable secret password. Task Command Syntax Create a password to enable [password | secret] [level level] access EXEC [encryption-type] password Privilege mode. Command Mode CONFIGURATION Create a Port-based VLAN The Default VLAN as VLAN
  • Dell S4810P | Quick Start Guide - Page 22
    frames leaving an interface in Layer 2 mode, you must assign that interface to a port-based VLAN to tag it with that VLAN ID. To tag interfaces, use these tag header. Command Mode CONFIGURATION INTERFACE Use the untagged command to move untagged interfaces from the Default VLAN to another VLAN:
  • Dell S4810P | Quick Start Guide - Page 23
    is VLAN 1. To assign another VLAN ID to the Default VLAN, use the default vlan-id vlan-id command. Task Command Syntax Configure an IP address ip address ip-address mask and mask on the interface. [secondary] Command Mode INTERFACE Connecting the S4810 to the Network Once you have completed the
  • Dell S4810P | Quick Start Guide - Page 24
    20 Installing the Software
  • Dell S4810P | Quick Start Guide - Page 25
  • Dell S4810P | Quick Start Guide - Page 26
    Printed in the U.S.A. www.dell.com | support.dell.com
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
Dell Force10
S4810 System
Quick Start Guide
Regulatory Model: S4810P