Dell S4810P Configuration Guide

Dell S4810P Manual

Get Dell S4810P PDF manuals and user guides View all Dell S4810P manuals
Add to My Manuals
Save this manual to your list of manuals

Dell S4810P manual content summary:

  • Dell S4810P | Configuration Guide - Page 1
    Dell Networking S4810 and Dell Force10 S4810 Switch Configuration Guide for Compellent iSCSI SANs Dell Storage Engineering July 2014 [email protected]
  • Dell S4810P | Configuration Guide - Page 2
    the express written permission of Dell Inc. is strictly forbidden. For more information, contact Dell. Dell, the Dell logo, and the Dell badge, Compellent, and Force10 are trademarks of Dell Inc. 2 SCG2001 Dell Networking S4810 and Force10 S4810 Configuration Guide for Compellent iSCSI SANs
  • Dell S4810P | Configuration Guide - Page 3
    Jumbo Frames...8 2.8 Configure flow control ...8 2.9 Configure spanning tree on edge ports...8 2.10 Configure VLAN...8 2.11 Save configuration ...8 2.12 Configure additional switch ...8 Additional resources...9 3 SCG2001 Dell Networking S4810 and Force10 S4810 Configuration Guide for Compellent
  • Dell S4810P | Configuration Guide - Page 4
    provides an overview of the switch configuration. Table 1 Switch specifications Dell Networking and Dell Force10 S4810 Switch vendor Dell Switch model S4810 Switch firmware 9.3.0.0 or later Note: For proper functionality, the switch must be at the switch firmware version shown in the table
  • Dell S4810P | Configuration Guide - Page 5
    1.3 Cabling diagram The cabling diagram shown below represents the Dell recommend method for deploying your servers and Compellent arrays. Figure 1 Cabling diagram 5 SCG2001 Dell Networking S4810 and Force10 S4810 Configuration Guide for Compellent iSCSI SANs
  • Dell S4810P | Configuration Guide - Page 6
    startup configuration is deleted, the factory default Enable mode password is force10. FTOS>#config FTOS(conf)#interface ManagementEthernet 0/0 FTOS(conf-if-ma-0/0)#no shutdown FTOS(conf-if-ma-0/0)#ip address ipaddress mask 6 SCG2001 Dell Networking S4810 and Force10 S4810 Configuration Guide for
  • Dell S4810P | Configuration Guide - Page 7
    . FTOS#configure FTOS(conf)#interface range tengigabitethernet 0/0 - 47 FTOS(conf -if-range-te-0/0-47)#switchport FTOS(conf -if-range-te-0/0-47)#no shutdown FTOS(conf -if-range-te-0/0-47)#exit FTOS(conf)#exit 7 SCG2001 Dell Networking S4810 and Force10 S4810 Configuration Guide for Compellent
  • Dell S4810P | Configuration Guide - Page 8
    command is used only on Server and Storage connected edge ports. FTOS(conf-if-range-te-0/0-47)#spanning-tree rstp edge-port FTOS(conf-if-range-te-0/0-47)#exit 2.10 Configure VLAN Dell recommends assigning a unique vlan_id (between 2-4094) for each switch fabric. For example, assign VLAN 100 on the
  • Dell S4810P | Configuration Guide - Page 9
    white papers, reference architectures, and sizing guidelines for enterprise applications and SANs, refer to: http://en.community.dell.com/techcenter/storage/w/wiki/5018.compellent-technical-content.aspx 9 SCG2001 Dell Networking S4810 and Force10 S4810 Configuration Guide for Compellent iSCSI SANs
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
Dell Networking S4810 and Dell Force10
S4810
Switch Configuration Guide for Compellent iSCSI SANs
Dell Storage Engineering
July 2014