Dell U3824DW UltraSharp 38 Curved USB-C Hub Monitor - Teardown Instructions
Dell U3824DW Manual
 |
View all Dell U3824DW manuals
Add to My Manuals
Save this manual to your list of manuals |
Dell U3824DW manual content summary:
- Dell U3824DW | UltraSharp 38 Curved USB-C Hub Monitor - Teardown Instructions - Page 1
DELL U3424DWB 1 1. Disassembly Procedures S1 Turn off power S2 To remove the stand: Place U3824DW monitor on U3818DW curve sponge jig S5 Pull out "CTRL BD FFC" from I/F BD to take off Rear Cover Press and hold the stand release button - Dell U3824DW | UltraSharp 38 Curved USB-C Hub Monitor - Teardown Instructions - Page 2
-BD 98*40" from Main SHD Tear off "MYLAR INTF-BD 71*41" from Main SHD Tear off "MYLAR BL-BD" from Main SHD DELL U3824DWB 2 S10 Tear off an acetate tape from "USB BD Wire" and Panel Unplug "USB BD Wire" from I/F BD Press and hold the center of connector to unplug - Dell U3824DW | UltraSharp 38 Curved USB-C Hub Monitor - Teardown Instructions - Page 3
DELL U3424DWB 3 S11 Disassemble a gasket from Panel S15 Unlock 19 screws to disassemble Middle Frame from Panel S12 Unlock 4 screws to disassemble Main SHD from Panel ( - Dell U3824DW | UltraSharp 38 Curved USB-C Hub Monitor - Teardown Instructions - Page 4
DELL U3824DWB 4 S19 Unlock 10 PCBA screws to disassemble "I/F BD", "SPS BD" and "LED Driver BD" from Main SHD S20 Tear off a tape from "FFC EDP" Unplug wires from I/F BD, SPS BD and LED Driver BD (Screw Torque: 8.5±1 Kgf) - Dell U3824DW | UltraSharp 38 Curved USB-C Hub Monitor - Teardown Instructions - Page 5
DELL U3424DWB 5 S21 Remove electrolyte capacitors (red mark) from printed circuit boards S21-1 Cut the glue between bulk cap. and PCB with a knife S21-2 Ensure cutting path within the glue, don't touch bulk cap. or PCB - Dell U3824DW | UltraSharp 38 Curved USB-C Hub Monitor - Teardown Instructions - Page 6
DELL U3824DWB 6 S21-3 Take out bulk cap. pin solder with soldering iron and absorber S21-4 Lift the bulk cap. up and away from the PCB - Dell U3824DW | UltraSharp 38 Curved USB-C Hub Monitor - Teardown Instructions - Page 7
DELL U3424DWB 7 2. Product material information The following substances, preparations, or components should be disposed of or recovered separately from other WEEE in compliance with Article 4 of
-
1 -
2 -
3 -
4 -
5 -
6 -
7
 |
 |
1
DELL U3424DWB
1. Disassembly Procedures
S1
Turn off power
S2
To remove the stand:
Place U3824DW monitor on U3818DW
curve sponge jig
Press and hold the stand release button
at the back of the display
Lift the stand assembly up and away
from the monitor
S3
Unlock 4 screws on Rear Cover
(Screw Torque:8-10Kgf)
S4
Use hands or Bar Scraper to
disassemble Rear Cover from Middle
Frame
Notice the disassembly order:
Left Side=>Top Side =>Right Side
=>Bottom Side
S5
Pull out “CTRL BD FFC” from I/F BD to
take off Rear Cover
S6
Tear off a tape from Rear Cover
Tear off “CTRL FFC” from Rear Cover
Unlock 3 screws to disassemble “CTRL
BD” from Rear Cover
(Screw Torque: 2.0+0.5 Kgf)
S7
Tear off a rubber from CTRL BD