Dell U4025QW UltraSharp 40 Curved Thunderbolt Hub Monitor - Teardown Instructi
Dell U4025QW Manual
![]() |
View all Dell U4025QW manuals
Add to My Manuals
Save this manual to your list of manuals |
Dell U4025QW manual content summary:
- Dell U4025QW | UltraSharp 40 Curved Thunderbolt Hub Monitor - Teardown Instructi - Page 1
: S1 Turn off power.. Unplug external cables(power cable and video S2 cable) from the monitor. DELL U4025QW 1 Wedge your fingers between the rear cover and the middle bezel on the corners of the top side of the monitor to release the rear cover, then use one hand S5 to press the middle bezel - Dell U4025QW | UltraSharp 40 Curved Thunderbolt Hub Monitor - Teardown Instructi - Page 2
2 DELL U4025QW Tear off 3pcs aluminum foil for releasing the cables and bracket. Use a Philips-head screwdriver to S9 remove 8pcs screws for unlocking the two speakers - Dell U4025QW | UltraSharp 40 Curved Thunderbolt Hub Monitor - Teardown Instructi - Page 3
DELL U4025QW 3 Lift up the bracket chassis, and disconnect the eDP cable from the connector of panel module, then put S14 the bracket chassis on a protective cushion. - Dell U4025QW | UltraSharp 40 Curved Thunderbolt Hub Monitor - Teardown Instructi - Page 4
4 DELL U4025QW Remove electrolyte capacitors (red mark) from S20 printed circuit boards. S20-4 Take out bulk cap. pin solder with soldering iron and absorber. S20-1 Cut the - Dell U4025QW | UltraSharp 40 Curved Thunderbolt Hub Monitor - Teardown Instructi - Page 5
DELL U4025QW 5 2. Product material information The following substances, preparations, or components should be disposed of or recovered separately from other WEEE in compliance with Article 4 of EU
![](/manual_guide/products/dell-u4025qw-ultrasharp-40-curved-thunderbolt-hub-monitor-teardown-instructions-7a3282a/1.png)
1
DELL U4025QW
Unplug external cables(power cable and video
cable) from the monitor.
S2
Turn off power..
1.
Disassembly Procedures:
S1
Remove stand from the product.(Press the stand
release button, lift the stand up and away from the
monitor)
S3
S4
Put the monitor on a protective cushion, then use a
Philips-head screwdriver to remove 4pcs screws for
unlocking mechanisms. Remove DP caps.
(No.1~4 screw size=M4x11; Torque=10
±
1kgfxcm)
S5
S6
S7
2
3
4
1
Wedge your fingers between the rear cover and the
middle bezel on the corners of the top side of the
monitor to release the rear cover, then use one hand
to press the middle bezel, the other hand to pull up
carefully the rear cover in order of arrow preference
for unlocking mechanisms of rear cover.
5
2
1
3
4
S8
Lift up the rear cover, and disconnect the joystick
cable and sensor cable away from the connectors,
and then remove the rear cover and put it aside.
(No.1~2 screw size=M2x2.4, Torque=1
±
0.2
kgfxcm)
Release the cables by tearing off all the tapes. Use a
Philips-head screwdriver to remove 2pcs screw for
unlocking the joystick board, then release the joystick
board sensor board from the hooks of the rear cover.
sensor board
1
2
Use a Philips-head screwdriver to remove 2pcs screws
for unlocking the IO cover with bracket, then release
the IO cover away from the main bracket chassis.
(No.1~2 screw size=M3x4,Torque=5
±
1kgfxcm)
2
1