Denon AVR-2105 Owners Manual

Denon AVR-2105 Manual

Get Denon AVR-2105 PDF manuals and user guides View all Denon AVR-2105 manuals
Add to My Manuals
Save this manual to your list of manuals

Denon AVR-2105 manual content summary:

  • Denon AVR-2105 | Owners Manual - Page 1
    AV SURROUND RECEIVER RÉCEPTEUR AUDIO-VIDÉO AVR-2105/885 OPERATING INSTRUCTIONS MODE D'EMPLOI FUNCTION VOLUME LEVEL MASTER VOLUME MAIN SOURCE ZONE 2 / REC SELECT ON / STANDBY ON OFF INPUT MODE ANALOG EXT. IN SIGNAL DIGITAL BAND SHIFT AUTO INPUT PCM ª PRESET • DTS OUTPUT SURROUND
  • Denon AVR-2105 | Owners Manual - Page 2
    the instructions contained in this manual, meets FCC requirements. Modification not expressly approved by DENON may void your authority, granted by the FCC, to use the product. 3. NOTE This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
  • Denon AVR-2105 | Owners Manual - Page 3
    POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H) 13. Power-Cord Protection - Power- grounding of the mast and supporting structure, grounding of the lead instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls
  • Denon AVR-2105 | Owners Manual - Page 4
    choosing the DENON AVR-2105/885 Digital A / V Surround Receiver. This remarkable Troubleshooting 72 ⁄9 Specifications 73 2 ACCESSORIES Check that the following parts are included in addition to the main unit: q Operating instructions 1 w Warranty 1 e Service station list 1 r Remote control
  • Denon AVR-2105 | Owners Manual - Page 5
    you want to use it. V.AUX INPUT S-VIDEO VIDEO L AUDIO R OPTICAL SETUP MIC SURROUND MODE SELECT TONE CONTROL SURROUND PARAMETER TONE DEFEAT AV SURROUND RECEIVER AVR-2105 2 CAUTIONS ON INSTALLATION Noise or disturbance of the picture may be generated if this unit or any other electronic
  • Denon AVR-2105 | Owners Manual - Page 6
    future multi-channel audio format(s), the AVR-2105/885 is provided with 5.1 channel (five main channels, plus one low frequency effects channel) inputs, along with a full set of 7.1 channel pre-amp outputs, controlled by the 8 channel master volume control. This assures future upgrade possibilities
  • Denon AVR-2105 | Owners Manual - Page 7
  • Denon AVR-2105 | Owners Manual - Page 8
    making connections, also refer to the operating instructions of the other components. • The AVR-2105/885 is equipped with a function for up- video coaxial pin plug cord. • Connect the video disc player's analog audio output jacks (ANALOG AUDIO OUTPUT) to the AUDIO DVD IN jacks using pin plug cords
  • Denon AVR-2105 | Owners Manual - Page 9
    jacks • When making connections, also refer to the operating instructions of the other components. • A note on the S input jacks The input selectors for the S inputs and Video inputs work in conjunction with each other. • The AVR-2105/885 is equipped with a function for converting video signals
  • Denon AVR-2105 | Owners Manual - Page 10
  • Denon AVR-2105 | Owners Manual - Page 11
    . Installation hole Mount on wall, etc. GROUND An F-type FM antenna cable plug can be connected directly. Connection of AM antennas 1. Push the lever. 2. Insert the conductor. 3. Return the lever. antenna. • Make sure AM loop antenna lead terminals do not touch metal parts of the panel. 11
  • Denon AVR-2105 | Owners Manual - Page 12
    DTS OUTPUT SURROUND BACK ZONE 2 ESET • ª TUNING • VIDEO SELECT DIMMER STATUS DIRECT / STEREO V.AUX INPUT S-VIDEO VIDEO L R L AUDIO R OPTICAL SETUP MIC SURROUND MODE SELECT TONE CONTROL SURROUND PARAMETER TONE DEFEAT AV SURROUND RECEIVER AVR-2105 LINE OUT DIGITAL OUT VIDEO OUT
  • Denon AVR-2105 | Owners Manual - Page 13
  • Denon AVR-2105 | Owners Manual - Page 14
    ventilation condition around the unit and switch the power back on. If the protection circuit is activated again even though there are no problems with the wiring or the ventilation around the unit, switch off the power and contact a DENON service center. Note on speaker impedance • The protector
  • Denon AVR-2105 | Owners Manual - Page 15
  • Denon AVR-2105 | Owners Manual - Page 16
    SURROUND BACK 5CH / 7CH DIRECT / STANDARD STEREO STEREO V.AUX INPUT S-VIDEO VIDEO L AUDIO R OPTICAL SETUP MIC SURROUND MODE SELECT TONE CONTROL SURROUND PARAMETER TONE DEFEAT AV SURROUND RECEIVER AVR-2105 t u o !1 q w e r y i !0 !4 !2 !3 !5 !6 !7 !8 q Power ON/STANDBY switch 21, 39
  • Denon AVR-2105 | Owners Manual - Page 17
    unit • For details on the functions of these parts, refer to the pages given in parentheses ( ). LED (indicator 35, 38) ZONE2 buttons 47) SURROUND buttons 41, 48, 58) ENGLISH Remote control signal transmitter 18) POWER buttons 21, 35~37, 39) MAIN buttons 47) Input source selector buttons
  • Denon AVR-2105 | Owners Manual - Page 18
    distance will shorten or operation will become difficult if there are obstacles between the remote control unit and the remote control sensor, if the remote control sensor is exposed to direct sunlight or other strong light, or if operated from an angle. • Neon signs or other devices emitting pulse
  • Denon AVR-2105 | Owners Manual - Page 19
    items and default values (set upon shipment from the factory) Auto Setup Speaker Configuration Delay Time Subwoofer Mode Crossover Frequency Test Tone System setup Power Amp Assignment Set this to switch the surround back channel's power amplifier for use for zone2. Input the combination of
  • Denon AVR-2105 | Owners Manual - Page 20
    OUT jack during playback of a video component. For example, if the TV monitor is connected to both the AVR-2105/885's S-Video and video monitor output jacks and signals are input to the AVR2105/885 from a video source (VDP, etc.) connected to both the S-Video and video input jacks, the on-screen
  • Denon AVR-2105 | Owners Manual - Page 21
    off and indicator is off. In this position, the power cannot be turned on and off from the remote control unit. 3 ON / STANDBY Turn on the power. Press the Power ON/STANDBY switch (button). (Main unit) (Remote control unit) 4 Press the SYSTEM SETUP button to enter the setting. *SYSTEM SET UP
  • Denon AVR-2105 | Owners Manual - Page 22
    unit. PHONES SPEAKER A B SURROUND BACK 5CH / 7CH DIRECT / STANDARD STEREO STEREO V.AUX INPUT S-VIDEO VIDEO L AUDIO R OPTICAL SETUP MIC SURROUND MODE SELECT TONE CONTROL SURROUND PARAMETER TONE DEFEAT AV SURROUND RECEIVER AVR-2105 Listening position 2 Place the microphone for Auto
  • Denon AVR-2105 | Owners Manual - Page 23
    not displayed. After each channel is measured, "Calculating" appears. The display switches to Auto Setup check screen automatically. About automatic retry Remeasurement starts automatically to receive proper result of measurement. Remeasurement is performed to 2 times, and "Retry1" or "Retry2" is
  • Denon AVR-2105 | Owners Manual - Page 24
    Set with the checked measurement value. • Retry : Perform the measurement again. • Cancel : Cancel the checked measurement value. (Remote control unit) A.Set
  • Denon AVR-2105 | Owners Manual - Page 25
    Set up in function of your speaker systems. Performing this setup optimizes the system. • The composition of the signals output to Frequency mode is sent to the subwoofer. None Select this when no speakers are installed. Yes/No Select "Yes" when a subwoofer is installed, "No" when a subwoofer is
  • Denon AVR-2105 | Owners Manual - Page 26
    delay time for the surround mode. Preparations: Measure the distances Subwoofer L1 L2 L5 Listening position SL L3 SBL L4 SR SBR NOTES: • No setting when "None" has been selected for the Speaker Configuration setting. • Surround back is not displayed when ZONE 2 is set with the POWER AMP
  • Denon AVR-2105 | Owners Manual - Page 27
    ) and the channel specified as "Small" in the setup menu. • Select the play mode that provides bass reproduction with quantity. • When the subwoofer is set to "Yes", bass sound is output from the subwoofer regardless of the subwoofer mode setting in surround modes other than Dolby/DTS. • In surround
  • Denon AVR-2105 | Owners Manual - Page 28
    can also be adjusted directly from the remote control unit. (For details, see page 48.) 1 • Use the (left) button to the Test Tone. • Press the ENTER or Assignment. (down) button to switch to the Digital In 18 T.TONE
  • Denon AVR-2105 | Owners Manual - Page 29
    each of the following surround modes: DIRECT, STEREO, STANDARD (DOLBY/DTS SURROUND), 5/7 CH STEREO, MONO MOVIE, ROCK ARENA, JAZZ CLUB, VIDEO GAME, MATRIX and VIRTUAL. Setting the Digital In Assignment • This setting assigns the digital input jacks of the AVR-2105/885 for the different input sources
  • Denon AVR-2105 | Owners Manual - Page 30
    the monitor output terminals. 1 Select the input source to be set. 26 DVD AUTO 2 Select the mode (input signal). 3 Press the ENTER or (down) button to switch the Auto Surround Mode setting. AUTO: When there are multiple input signals, the input signals are detected and the input signal to
  • Denon AVR-2105 | Owners Manual - Page 31
    SW Level Set the playback level of the analog input signal connected to the Ext. In terminal. 1 Select desired setting. • Select according to the specifications of the player being used. Also refer to the player's operating instructions. • +15dB (default) recommended. (0, +5, 10 and +15 can be
  • Denon AVR-2105 | Owners Manual - Page 32
    ENGLISH Power Amp Assignment Setting the power amplifier assignment • Make this setting to switch the power amplifier for the surround Use this to turn the on-screen display (messages other than the menu screens) on or off. • Sets the on-screen display's display mode. Mode 1: Prevents flickering
  • Denon AVR-2105 | Owners Manual - Page 33
    This completes the system setup operations. Once the system is set up, there is no need to make the settings again unless other components or speakers are connected to or the speaker layout is changed. • On-screen display signals Signals input to the AVR-2105/885 On-screen display signal output
  • Denon AVR-2105 | Owners Manual - Page 34
    REMOTE CONTROL UNIT Operating DENON audio components • Turn on the power of the different components before operating them. 1 Set mode switch 1 to "AUDIO". 2 Set mode +, - up/down TUNING : Frequency +, - up/down BAND : Switch between the AM and FM bands MODE : Switch between auto and
  • Denon AVR-2105 | Owners Manual - Page 35
    set for one component only among the following: CDR/MD, DVD/VDP and DBS/CABLE. The preset codes are as follows upon shipment from the factory and after resetting: TV, VCR HITACHI CD, TAPE DENON CDR/MD DENON (CDR) DVD/VDP DENON (DVD) DBS/CABLE ABC (CABLE) 35
  • Denon AVR-2105 | Owners Manual - Page 36
    • For details, refer to the component's operating instructions. Some models cannot be operated with this remote control unit. 1. Digital video disc player (DVD) system buttons POWER : Power on/standby (ON/SOURCE) OFF : DENON DVD Power off 6,7 : Manual search (forward and reverse) 2 : Stop 1 : Play
  • Denon AVR-2105 | Owners Manual - Page 37
    POWER : Power on/standby (ON/SOURCE) 6,7 : Manual search (forward and reverse) 2 : Stop 1 : Play 3 : Pause Channel +, - : Channels 4. Digital broadcast satellite (DBS) tuner and cable (CABLE) system buttons POWER : Power same way as for Denon audio components (page 34). • The TV can
  • Denon AVR-2105 | Owners Manual - Page 38
    function allowing you to operate the PLAY, STOP, MANUAL SEARCH and AUTO SEARCH buttons on the CD, TAPE, CDR/MD, DVD/VDP or VCR components when in the DBS/CABLE or TV mode. By default, nothing is set. 1 Set mode switch 1 to "VIDEO". 3 3 2 Set mode switch 2 to the component to be registered (DBS
  • Denon AVR-2105 | Owners Manual - Page 39
    ON / STANDBY (Main unit) (Remote control unit) When pressed, the power turns on and the display lights. The sound is muted for several seconds, after which the unit operates normally. When pressed again, the power turns off, the standby mode is set and the display turns off. 3 Select the front
  • Denon AVR-2105 | Owners Manual - Page 40
    the separate input sources are stored in the memory. q AUTO (auto mode) In this mode, the types of signals being input to the digital and analog input jacks for the selected input source are detected and the program in the AVR-2105/885's surround decoder is selected automatically upon playback. This
  • Denon AVR-2105 | Owners Manual - Page 41
    parameters, tone defeat or tone control, press the surround mode button then operate the selector. (Remote control unit) SURROUND MODE (Main unit) 4 Start playback on the selected component. • For operating instructions, refer to the component's manual. 5 Adjust the volume. MASTER VOLUME
  • Denon AVR-2105 | Owners Manual - Page 42
    this mode. • If the subwoofer output level seems to high, set the "SW ATT." surround parameter to "ON". Playing audio sources (CDs and DVDs) The AVR-2105/885 is equipped with two 2-channel playback modes exclusively for music. Select the mode to suit your tastes. 1 DIRECT mode Use this mode to
  • Denon AVR-2105 | Owners Manual - Page 43
    function will not work in the direct mode. 1 The tone switches as follows each time the TONE CONTROL button is pressed. TONE CONTROL BASS TREBLE (Main unit) 2 With the name of the volume to be adjusted selected, turn the SELECT SELECT knob to adjust the level. (Main unit) • To increase
  • Denon AVR-2105 | Owners Manual - Page 44
    can be checked during playback by pressing the remote (Remote control unit) control unit's ON SCREEN/DISPLAY button. Such 3 Set the recording mode. • For operating instructions, refer to the manual of the component on which you want to record. 4 To cancel, turn the function knob and
  • Denon AVR-2105 | Owners Manual - Page 45
    the diagram below.) • ZONE 2 SPEAKER OUT and PRE OUT can be used when "ZONE2" is selected at System Setup Menu "Power Amp Assignment". In this case, Surround Back Speaker Out cannot be used for MAIN ZONE. • When a sold separately room-to-room remote control unit (DENON RC-616, 617 or 618) is wired
  • Denon AVR-2105 | Owners Manual - Page 46
    ENGLISH 2 When using the SURR.BACK/ZONE2 amplifier as the ZONE2. • The SPEAKER OUT, LINE OUT and PRE OUT terminals can be used simultaneously in ZONE2. • To use the ZONE2, turn on the ZONE2 button (remote control unit). • The output of ZONE2 SPEAKER OUT & SURR BACK RCA terminals can be adjusted via
  • Denon AVR-2105 | Owners Manual - Page 47
    For operating instructions, refer to the manuals of the respective components. 4 To cancel, turn the function remote control unit. (This is only possible when the main unit in the ZONE2 mode.) (Remote control unit) OUTPUT SURROUND BACK ZONE 2 (Light) The main zone output can be turned
  • Denon AVR-2105 | Owners Manual - Page 48
    the different speakers. This adjustment can be performed with the system setup (see page 19) or from the remote control unit, as described below. • Adjusting with the remote control unit using the test tones is only possible in the "Auto" mode and only effective in the STANDARD (DOLBY/DTS SURROUND
  • Denon AVR-2105 | Owners Manual - Page 49
    ENGLISH • After adjusting using the test tones, adjust the channel levels either according to the "SB". "SB" appears only when "POWER AMP ASSIGN" setting is SURR. BACK mode. NOTE: Please make sure the "AUDIO" position of the slide switch on the remote control unit. 2 Adjust the level of the
  • Denon AVR-2105 | Owners Manual - Page 50
    in the Dolby Surround Pro Logic IIx mode. 6 4 5, 7 6 (Main unit) (Remote control unit) • The Dolby Pro Logic II indicator lights. Display Light LOGICII 3 Play a program source with the mark. • For operating instructions, refer to the manuals of the respective components. 4 SURROUND
  • Denon AVR-2105 | Owners Manual - Page 51
    is set to "ON". (Set "S. BACK" at system set up to SELECT "SMALL" or "LARGE".) (Main unit) (Remote control unit) (Pro Logic IIx Cinema mode) (Pro Logic IIx Music mode) (Pro Logic IIx Game mode) or or • When the "SB CH OUT" parameter is set to "OFF". (Set "S. BACK" at system set up
  • Denon AVR-2105 | Owners Manual - Page 52
    3 Play a program source. 4 Select the surround parameter mode. Display SURROUND PARAMETER MODE cinema (Main unit) (Remote control unit) The DTS NEO:6 Cinema or Music mode can be chosen directly by pressing the CINEMA or MUSIC button on the remote control unit during playback in the DTS NEO
  • Denon AVR-2105 | Owners Manual - Page 53
    . 9 Press the ENTER button to finish surround parameter mode. (Remote control unit) NOTE: • When making parameter settings, the SB channels). • Music This mode is suited mainly for playing music. The front channel (FL and FR) signals bypass the decoder and are played directly so there is no loss
  • Denon AVR-2105 | Owners Manual - Page 54
    SURROUND MODE button, then turn the SELECT knob and select Dolby Pro Logic IIx or DTS NEO:6. SURROUND MODE SELECT (Main unit) (Main unit) 3 Operate the SURROUND BACK button to switch Surround Back CH ON/OFF. SURROUND BACK SURROUND BACK Light (Main unit) (Remote control unit) • Lights when
  • Denon AVR-2105 | Owners Manual - Page 55
    parameters. SURROUND PARAMETER (Main unit) (Remote control unit) (Remote control unit) 7 Adjust the parameter settings. SELECT (Main unit) (Remote control unit) 8 Press the ENTER button to finish surround parameter mode. ENGLISH (Remote control unit) NOTE: • When making parameter
  • Denon AVR-2105 | Owners Manual - Page 56
    DTS sources when the peak limiter is turned off with the subwoofer peak limit level setting (system setup menu), adjust the level as necessary. This adjusts the tone control. This can be set individually for the separate shroud mode other than Pure direct and direct mode. SB CH OUT (Surround
  • Denon AVR-2105 | Owners Manual - Page 57
    achieve a more realistic, powerful sound. Surround modes and their features 1 directions. This mode creates the sound field of a live house with a low ceiling and hard walls. This mode modes set for that source last time it was used are automatically recalled. The surround parameters, tone control
  • Denon AVR-2105 | Owners Manual - Page 58
    the SURROUND PARAMETER button is pressed for the different surround modes. (Remote control unit) 3 Select the various parameters. 3 2, 3 4 3 (Remote control unit) (Remote control unit) 4 Adjust the parameter settings. (Remote control unit) 5 Press the ENTER button to finish surround
  • Denon AVR-2105 | Owners Manual - Page 59
    from the main unit's panel. 1 Turn the SELECT knob to select the surround mode. SELECT ENGLISH (Main unit) • When turned clockwise DIRECT STEREO DOLBY PRO LOGIC IIx DTS NEO:6 VIRTUAL SURROUND MATRIX VIDEO GAME • When turned counterclockwise DIRECT STEREO DOLBY PRO LOGIC IIx DTS NEO
  • Denon AVR-2105 | Owners Manual - Page 60
    signals C C E C * C C * E C C C C C C C C When playing When playing PCM signals ANALOG signals C C C C E C C C C C C C E E E E C C C C C C C C C C C C C C When playing Dolby Digital and DTS signals Mode D. COMP. LFE DIRECT STEREO EXTERNAL INPUT DOLBY PRO LOGIC II
  • Denon AVR-2105 | Owners Manual - Page 61
    also be performed at "System setup". (See page 33.) 1 1 When the main unit's power operation switch turn on while pressing the set's "Manual tuning" operation to tune in the station, then preset it using the manual "Preset memory" operation. • To interrupt this function, press the power
  • Denon AVR-2105 | Owners Manual - Page 62
    . NOTE: • When in the auto tuning mode on the FM band, the "STEREO" indicator lights on the display when a stereo broadcast is tuned in. At open frequencies, the noise is muted and the "TUNED" and "STEREO" indicators turn off. Lit (Remote control unit) Manual tuning 1 Set the input function to
  • Denon AVR-2105 | Owners Manual - Page 63
    Preset stations 23 3 1, 4 2 ENGLISH Preparations: Use the "Auto tuning" or "Manual tuning" operation to tune in the station to be preset in the memory. 1 Press the MEMORY button. (Remote control unit) 2 Press the SHIFT button and select the desired memory block (A to G). SHIFT (Main unit
  • Denon AVR-2105 | Owners Manual - Page 64
    of the microprocessor is required by the following procedure. 1 Switch off the unit using the main unit's power switch. 2 Hold the following SPEAKER A button and B button, and turn the main unit's power switch. 3 Check that the entire display is flashing with an interval of about 1 second, and
  • Denon AVR-2105 | Owners Manual - Page 65
    speakers, are required in order to achieve the ideal sound. The AVR-2105/885 is equipped the function of surround speakers selection that makes it possible to position), as well as a separate pair of direct radiating (monopolar) speakers placed at the rear corners of the listening room. 65
  • Denon AVR-2105 | Owners Manual - Page 66
    the sides to the back and from the front to the point directly behind the listening position. Change of positioning and acoustic image with 5.1- channel and DTS Surround 5.1-channel sources. Furthermore, all the Denon original surround modes (see page 57) are compatible with 7.1-channel playback, so
  • Denon AVR-2105 | Owners Manual - Page 67
    number of speaker settings for different purposes. Use these examples as guides to set up your system according to the type of speakers used Consult the owner's manual for your subwoofer for advice on placing the subwoofer within the listening room. • If the surround speakers are direct-radiating (
  • Denon AVR-2105 | Owners Manual - Page 68
    the instruction manual of the adapter when making connection. 2 Some DVD digital outputs have the function of switching the Dolby Digital signal output method between "bit stream" and "(convert to) PCM". When playing in Dolby Digital surround on the AVR-2105/885, switch the DVD player's output mode
  • Denon AVR-2105 | Owners Manual - Page 69
    of these signals is input to the AVR-2105/885, the surround mode is automatically set to Dolby Pro Logic II when the "DOLBY/DTS SURROUND" mode is selected. 2 Sources recorded in Dolby Surround are indicated with the logo mark shown below. Dolby Surround support mark: Manufactured under license from
  • Denon AVR-2105 | Owners Manual - Page 70
    so the DTS-ES Matrix 6.1 mode must be set manually to play these sources. (For instructions on selecting the surround mode, see page 54.) The DTS-ES decoder includes another function, the DTS Neo:6 surround mode for 6.1-channel playback of digital PCM and analog signal sources. 2 DTS Neo:6™ surround
  • Denon AVR-2105 | Owners Manual - Page 71
    recent years, and there are a growing number of high quality signal sources, including 96 kHz/24 bit 5.1-channel sources. For example, there are high picture/sound quality DVD video sources with 96 kHz/24 bit stereo PCM audio tracks. However, because the data rate for these audio tracks is extremely
  • Denon AVR-2105 | Owners Manual - Page 72
    problems when listening to the CD, records, tapes and FM broadcasts, etc. Symptom Cause Measures DISPLAY not lit and sound not produced • Power cord not plugged in securely. when power switch set to on. • Check the insertion of the power cord plug. • Turn the power on with the remote control
  • Denon AVR-2105 | Owners Manual - Page 73
    ENGLISH 19 SPECIFICATIONS 2 Audio section • Power amplifier Rated Analog Input sensitivity / input impedance: 200 mV / 47 kΩ/kohms Frequency response: 10 Hz ~ 100 kHz: +1, -3 dB (DIRECT mode) S/N: 100 dB (IHF-A weighted) (DIRECT mode) Distortion: 0.008% (20 Hz ~ 20 kHz) (DIRECT mode
  • Denon AVR-2105 | Owners Manual - Page 74
    PRESET CODES / LISTE DE CODES PRÉRÉGLÉS DVD Denon Aiwa Hitachi JVC Konka Magnavox Mitsubishi Panasonic Philips Pioneer Sanyo 005, 015, 016, 017 003, 008 018 002, 019, 020 001, 021, 022 023 VDP Denon Magnavox Mitsubishi Panasonic Philips Pioneer RCA Sony 028, 029, 112 026 028 029, 030 026 028, 031
  • Denon AVR-2105 | Owners Manual - Page 75
    Minolta 013, 023 Mitsubishi 001, 003, 008, 013, 014, 017, 027, 029, 039, 040, 041, 045, 097 Motorola 081 Montgomery Ward 001, 002, 007, 009, 049, 063, 081, 115, 117 MTC 009, 087, 094 Multitech 007, 009, 011, 087, 090, 094 NAD 038 NEC 004, 005, 006, 018, 026, 029, 045, 061, 062, 085
  • Denon AVR-2105 | Owners Manual - Page 76
    , 127, 131, 132, 145, 147 Philips 005, 015, 017, 050, 051, 056, 078, 087, 088, 089, 131, 132, 147 Pioneer 124, 128, 142 Portland 054 Price Club 095 Proscan 040, 044, 125 Proton 035, 051, 092, 129 Pulsar 042 Quasar 036, 037, 074, 141 Radio Shack 011, 044, 063, 093, 118
  • Denon AVR-2105 | Owners Manual - Page 77
    Samsung Sansui Sanyo SBR Schneider Scott Sears Sharp Siemens Signature Simpson Sony Soundesign Spectricon Squareview Supre-Macy Supreme Sylvania Symphonic Tandy Tatung Technics Teknika Tera Toshiba Universal Victor Video Concepts Viking Wards Zenith Zonda 003, 015, 034, 053, 055, 057, 094, 095, 136
  • Denon AVR-2105 | Owners Manual - Page 78
    *[111], 112 112 113 003, 004 007 005 006 148 TAPE Denon Aiwa Carver Harman/Kardon JVC Kenwood Magnavox Marantz Onkyo Optimus Panasonic Philips Pioneer 012 004 007 010, 011 *[ ] : Preset codes set upon shipment from the factory. *[ ] : Les codes préréglés diffèrent en fonctiom des livraison de l'
  • Denon AVR-2105 | Owners Manual - Page 79
    MEMO: 149
  • Denon AVR-2105 | Owners Manual - Page 80
    MEMO: 150
  • Denon AVR-2105 | Owners Manual - Page 81
    MEMO: 151
  • Denon AVR-2105 | Owners Manual - Page 82
    16-11, YUSHIMA 3-CHOME, BUNKYO-KU, TOKYO 113-0034, JAPAN Telephone: (03) 3837-5321 Printed in China 511 4182 000
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
SELECT
AUTO
INPUT MODE
EXT. IN
BAND
SHIFT
ª
•
ª
TUNING
PRESET
•
DIMMER
STATUS
SURROUND
BACK
ZONE 2
PCM
DTS
SIGNAL
DIGITAL
INPUT
OUTPUT
ANALOG
VIDEO SELECT
S-VIDEO
OPTICAL
SETUP MIC
VIDEO
V.AUX INPUT
L
AUDIO
R
MAIN
SOURCE
ZONE 2 /
REC SELECT
A
B
SPEAKER
STANDARD
5CH / 7CH
STEREO
DIRECT /
STEREO
SURROUND
BACK
SURROUND
PARAMETER
TONE
DEFEAT
SURROUND
MODE
TONE
CONTROL
ON / STANDBY
MASTER VOLUME
FUNCTION
AVR-2105
AV SURROUND RECEIVER
ON
OFF
PHONES
SELECT
2
We greatly appreciate your purchase of this unit.
2
To be sure you take maximum advantage of all the
features this unit has to offer, read these instructions
carefully and use the set properly. Be sure to keep this
manual for future reference should any questions or
problems arise.
“SERIAL NO.
PLEASE RECORD UNIT SERIAL NUMBER ATTACHED TO
THE REAR OF THE CABINET FOR FUTURE REFERENCE”
“NO. DE SERIE
PRIERE DE NOTER LE NUMERO DE SERIE DE L’APPAREIL
INSCRIT A L’ARRIERE DU COFFRET DE FAÇON A POUVOIR
LE CONSULTER EN CAS DE PROBLEME.”
2
Nous vous remercions pour l’achat de cet appareil.
2
Pour être sûr de profiter au maximum de toutes les
caractéristiques qu’offre cet appareil, lire avec soin ces
instructions et bien utiliser l’appareil. Toujours
conserver ce mode d’emploi pour s’y référer
ultérieurement en cas de question ou de problème.
FOR ENGLISH READERS
PAGE
2
~
PAGE
73, 144 ~ 148
POUR LES LECTEURS FRANCAIS
PAGE
2, 74
~
PAGE
148
AV SURROUND RECEIVER
RÉCEPTEUR AUDIO-VIDÉO
AVR-2105/885
OPERATING INSTRUCTIONS
MODE D’EMPLOI