Home » Denon Manuals » Home Theater Systems » Denon DRA-697CI » Manual Viewer

Denon DRA-697CI Serial Protocol

Denon DRA-697CI - AV Receiver Manual

UPC - 081757507332

View all Denon DRA-697CI manuals

Add to My Manuals
Save this manual to your list of manuals

Denon DRA-697CI manual content summary:

Denon DRA-697CI | Serial Protocol - Page 1
DENON AVR/AVC/DRA control protocol Application model : DRA-697CI Application terminal : RS-232C Connector specification Connector type : DB-9pin female type, slave straight connection (DCE type) ( 1pin : GND , 2pin : TxD , 3pin : RxD , 5pin : Common(GND) , 4,6,7,8,9pin : NC ) Communication
Denon DRA-697CI | Serial Protocol - Page 2
AVR/AVC/DRA) if the 'request command' (COMMAND+?+CR(0x0D)) has came from a controller. The RESPONSE should be sent within 200ms of receiving the COMMAND. *The form of RESPONSE presupposes that it is the same as that of EVENT. Basic specification SI : Select Input source MS : surround Mode Setting
Denon DRA-697CI | Serial Protocol - Page 3
The example of a command * is the meaning of 0x0D. SIDVD : Select Input source DVD MVUP : Master Volume UP PWON : system PoWer ON PWSTANDBY : system PoWer STANDBY SI? : Request command for now playing input source >> Return RESPONSE 'SI***' - 3 -
Denon DRA-697CI | Serial Protocol - Page 4
Others A) COMMAND is receivable also during transmission of EVENT. B) Since CHANNEL VOLUME changes simultaneously when the SURROUND MODE changes, the value of the channel volume of all channels returns as EVENT. C) CHANNEL VOLUME returns the data of ALL channels by the present SURROUND MODE also
Denon DRA-697CI | Serial Protocol - Page 5
UP SW DOWN SW ** ? ON OFF ? ATUNER PHONO CD CDR/TAPE DVD VCR IPOD V.AUX XM function 80=0dB, 99=---(MIN) Request MV Status CHANNEL VOLUME UP/DOWN , direct change to **dB Status OUTPUT MUTE ON/OFF change Request MU Status Select INPUT source MV , CV COMMAND : "*" parameter uses two ASCII characters.
Denon DRA-697CI | Serial Protocol - Page 6
SEARCH ON OFF ? UP DOWN ** PHONO ATUNER CD DVD V.AUX CDR/TAPE iPOD VCR XM SOURCE MUON MUOFF MU? BAND TPUP TPDOWN TFXM*** function MAIN-ZONE ON/OFF change Request ZM Status TUNER BAND SELECT TUNER SEARCH SELECT MUTI ZONE-2 ON/OFF change Request Z2 Status MULTI ZONE-2 VOLUME UP/DOWN , direct change
Denon DRA-697CI | Serial Protocol - Page 7
COMMAND Z3 SV PARAMETER ON OFF ? UP DOWN ** PHONO ATUNER CD DVD V.AUX CDR/TAPE iPOD VCR XM SOURCE MUON MUOFF MU? BAND TPUP TPDOWN TFXM*** DVD VCR V.AUX SOURCE ? function MLUTI ZONE-3 ON/OFF change Request Z3 Status MULTI ZONE-3 VOLUME UP/DOWN , direct change to **dB **:00 to 99 by ASCII , 80=0dB,
Denon DRA-697CI | Serial Protocol - Page 8
SPB On/Off Setting Request SPA/B Setting TUNER Frequency UP/DOWN , direct change --- ****.** kHz at AM band (>050000 is AM.) ****.** MHz at FM band (
Denon DRA-697CI | Serial Protocol - Page 9
MARGINAL SIGNAL NOSIGNAL PURE DIRECT ON PURE DIRECT OFF ? function ---Band set to AM ---Band set to FM ---Band set to XM Request TM Status ---Tuning mode set to AUTO mode ---Tuning mode set to MANUAL mode XM CH NAME change (Band XM Only) XM ARTIST NAME change (Band XM Only) XM
Denon DRA-697CI | Serial Protocol - Page 10
Left Control Cursor Right Control Enter Control Play/Pause Control Pause Control Stop Control Skip Plus Control Skip Minus Control Manual Search Plus Control Manual Search Minus Control Repeat One Control Repeat All Control Repeat Off Control Shuffle Songs Control Shuffle Album Control Shuffle Off
Denon DRA-697CI | Serial Protocol - Page 11
※Cursor/Enter/Setup EVENT SS PARAMETER CUP CDN CLT CRT ENT MEN ON MEN OFF function "Cursor Up" Control "Cursor Down" Control "Cursor Left" Control "Cursor Right" Control "Enter" Control "System Setup Menu ON" Control "System Setup Menu OFF" Control example SSCUP SSCDN SSCLT SSCRT
Denon DRA-697CI | Serial Protocol - Page 12
> 98 = +18dB(MAX) 80 = 0dB 00 = -80dB 99 = ---(MIN) CV FL ** CHANNEL VOLUME change , **:00,38 to 62 by ASCII CVFL 50 FR ** 62 = +12dB(MAX ON/OFF change MUON OFF MUOFF SI ATUNER INPUT source change SIATUNER PHONO SIPHONO CD SICD CDR/TAPE SICDR/TAPE
Denon DRA-697CI | Serial Protocol - Page 13
ON/OFF change OFF MUON ZONE2 OUTPUT MUTE ON/OFF change MUOFF Z3 PHONO MULTI ZONE-3 source change | ---The name of PARAMETER is CDR/TAPE the same as that of the time of SI COMMAND. SOURCE MULTI ZONE-3 mode cancel ** MULTI ZONE-3 VOLUME change , **:10 to 99 by ASCII 98 = +18dB(MAX) 80
Denon DRA-697CI | Serial Protocol - Page 14
EVENT PS PARAMETER TONE DEFEAT ON TONE DEFEAT OFF BAS ** TRE ** LOU ON LOU OFF FRONT SPA FRONT SPB FRONT A+B FRONT OFF function PARAMETER setting TONE DEFEAT ON/OFF BASS change, **:40 to 60 by ASCII, 50=0dB(-10dB～10dB) TREBLE change, **:40 to 60 by ASCII, 50=0dB(-10dB～10dB) PARAMETER setting
Denon DRA-697CI | Serial Protocol - Page 15
(Band XM Only) **(PRESET No.) TUNER PRESET change to No.** AM FM XM AUTO MANUAL CH NAME ******** (8 digit) ARTIST 16 digit) TITLE 16 digit) XMID ---Band set to AM ---Band set to FM ---Band set to XM ---Tuning mode set to AUTO mode ---Tuning mode set to MANUAL mode XM CH NAME change (Band XM Only
Denon DRA-697CI | Serial Protocol - Page 16
※iPod Extended Control EVENT PARAMETER IPA 0 1 function FLD Information(iPOD) is Answered By the IPA Command. Display Line1 Information Display Line2 Information IPA0 CR> IPA1 CR> *:ASCII CODE Character(MAX95Byte) _:Null ?:Exclusion(The character after Null should be disregarded) ※:Cursor