EVGA 112-CK-NF77-A1 Installation Guide
EVGA 112-CK-NF77-A1 Manual
 |
View all EVGA 112-CK-NF77-A1 manuals
Add to My Manuals
Save this manual to your list of manuals |
EVGA 112-CK-NF77-A1 manual content summary:
- EVGA 112-CK-NF77-A1 | Installation Guide - Page 1
- EVGA 112-CK-NF77-A1 | Installation Guide - Page 2
, Pentium EE, Pentium, and Celeron Socket 775 CPU's. (up to 1066Mhz FSB on 610i motherboards) ‰ Cooling fan and heat sink for the microprocessor ‰ System memory support: Supports single channel DDR2 533/667/800, (800MHz not supported on 610i Motherboards ) ‰ Power Supply The power supply requirement - EVGA 112-CK-NF77-A1 | Installation Guide - Page 3
onboard • Gigabit Ethernet (10/100 LAN on 610i motherboards) ‰ Onboard 1394 • 1394 port and header available on 630i Motherboards Onboard Audio • Supports 8-channel audio (6-channel on 112-CK-NF71-T1) • Supports S/PDIF output (on 630i motherboards) • Supports Jack-Sensing function ‰ PCI Express x16 - EVGA 112-CK-NF77-A1 | Installation Guide - Page 4
section will guide you through the installation of the motherboard. The topics covered in this section are: ‰ Preparing the motherboard • Installing the CPU • Installing the CPU fan • Installing the memory ‰ Installing the motherboard ‰ Connecting cables and setting switches Safety Instructions To - EVGA 112-CK-NF77-A1 | Installation Guide - Page 5
EVGA nForce Motherboard The EVGA nForce motherboard with the 600 series MCP processor is a PCI Express motherboard with an onboard GeForce graphics card. Figure 1 shows the 7150/630i motherboard and Figures 2 shows the back panel connectors. - EVGA 112-CK-NF77-A1 | Installation Guide - Page 6
Preparing the Motherboard The motherboard shipped in the box does not contain a CPU or memory. You need to purchase a CPU, a CPU heat sink/fan assembly, and memory module(s) to complete this installation. - EVGA 112-CK-NF77-A1 | Installation Guide - Page 7
while you close and engage the socket lever. Align notches with notches on the CPU Installing the CPU heat sink/fan There are many different heat sink types that can be used with this motherboard. Follow the instruction that came with your fan assembly. Be sure that the fan orientation is correct - EVGA 112-CK-NF77-A1 | Installation Guide - Page 8
Also make sure the CPU Fan assembly is aligned with the vents on the covers. Installing the I/O Shield The motherboard kit comes with an according to the fan assembly instruction. 5. Secure the motherboard with a minimum of six screws. Power Connections This motherboard requires an ATX power supply - EVGA 112-CK-NF77-A1 | Installation Guide - Page 9
8-pin ATX 12V power connection, is used to provide power to the CPU. Align the pins to the connector and press firmly until seated. It serial ATA connectors on the motherboard that support RAID 0, RAID 1, RAID 5, and RAID 0+1 configurations. (610i motherboards support RAID0 or RAID1 only) Connecting - EVGA 112-CK-NF77-A1 | Installation Guide - Page 10
a USB bracket. Audio The audio connector supports the HD audio standard. Most cases come - Analog port 2 - left channel (Headphone) 10 SENSE2_RETURN - Jack CPU fan cable can be either a 3-pin or a 4-pin connector. Connect a 3-pin connector to pins 1, 2, and 3 on the motherboard connector. CPU - EVGA 112-CK-NF77-A1 | Installation Guide - Page 11
Motherboard. Expansion Slots The EVGA nForce motherboard contains four expansion slots, two PCI Express slots and two PCI slots. For a full list of PCI Express x16 graphics card supported by this motherboard, go to www.evga in the BIOS setup if needed. Boot from your OS disk. Once your operating - EVGA 112-CK-NF77-A1 | Installation Guide - Page 12
Keyboard Init Initialized the mouse Check Check the integrity of the ROM,BIOS and message EEPROM Check Flash type and copy flash Write/erase routines Test and Reset CMOS Load Chipset Defaults Initialize onboard clock generator CPU ID and initialize L1/L2 cache Initialize first 120 interrupt vectors - EVGA 112-CK-NF77-A1 | Installation Guide - Page 13
registers Init PNP Shadow system/video BIOS Gen Init onboard clock generator and sensor Setup BIOS DATA AREA (BDA) Chipset programming and CPU Speed detect Initialize Video Test Video Memory and display Logos Early Keyboard Reset Test DMA channel 0 Test DMA channel 1 Test DMA Page Registers Test - EVGA 112-CK-NF77-A1 | Installation Guide - Page 14
4C Reserved 4D Reserved 4E Init APIC 4F Reserved 50 USB init Initialize 51 Reserved 52 Memory Test 53 Reserved 54 Reserved 55 CPU display 56 Reserved 57 PnP Init 58 Reserved 59 Setup Virus 5A Reserved 5B Awdflash Load 5C Reserved 5D Onboard I/O Init 5E Reserved - EVGA 112-CK-NF77-A1 | Installation Guide - Page 15
92 Reserved 93 Boot Medium Read 94 Final Init 95 NumLock 96 Boot Attempt C0 Base CPU test Description Initialize floppy disk drive Install FDD and setup BIOS data area parameters Initialize hard drive controller IDE device detection Initialize serial ports Initialize parallel ports - EVGA 112-CK-NF77-A1 | Installation Guide - Page 16
Code(hex) C1 C2 C3 C4 C5 C6 FF Name Memory Presence Early Memory Extend Memory Special Display Early Shadow Cache presence Boot Description Base memory detect Board Initialization Turn on extended memory, cache initialization First display initialization Early shadow enable for fast boot External - EVGA 112-CK-NF77-A1 | Installation Guide - Page 17
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
 |
 |
