Epson SureColor F2270 Standard Edition Start Here - Installation Guide
Epson SureColor F2270 Standard Edition Manual
 |
View all Epson SureColor F2270 Standard Edition manuals
Add to My Manuals
Save this manual to your list of manuals |
Epson SureColor F2270 Standard Edition manual content summary:
- Epson SureColor F2270 Standard Edition | Start Here - Installation Guide - Page 1
Epson® SureColor® F2270 Start Here IMPORTANT: Before using this product, make sure you read these instructions and the safety instructions in the online User's Guide. Choose a Location for the Printer Choose a location for the printer that is near a wall outlet where the power cord can be easily - Epson SureColor F2270 Standard Edition | Start Here - Installation Guide - Page 2
clip at the top of the waste ink bottle holder. Note: Do not throw the carriage lock away; you need it if you transport the printer. 9 Attach three tube clamps to the rear cover and route the waste ink tube through the clamps as shown. 13 Place the tube next to - Epson SureColor F2270 Standard Edition | Start Here - Installation Guide - Page 3
set 2 if the printer will be using High speed color mode. 6 Follow the instructions on the touchscreen to printer is charging or you'll waste ink. Note: • If you selected White ink mode or High speed color mode, use a glove to load the ink charging unit. After use, see the online User's Guide - Epson SureColor F2270 Standard Edition | Start Here - Installation Guide - Page 4
described in "Epson technical support." Epson technical support Visit http://epson.com/support/f2270 (U.S.), http://epson.ca/support/f2270 (Canada), or http://latin.epson.com/support/f2270 (Caribbean) to download software and utilities, view manuals, get FAQs and troubleshooting advice, or contact
-
1 -
2 -
3 -
4
 |
 |
Epson
®
SureColor
®
F2270
Start Here
IMPORTANT:
Before using this product, make sure you read these instructions
and the safety instructions in the online
User’s Guide
.
Choose a Location for the Printer
Choose a location for the printer that is near a wall outlet where the power cord
can be easily unplugged. Avoid places subject to rapid changes in temperature
and humidity. Also keep the printer away from direct sunlight, strong light, or
heat sources.
Make sure to place the printer on a flat, stable surface with enough space on
all sides (see illustrations below). The surface supporting the printer should
be wider than the space between the rubber feet on the bottom of the printer,
between 23.6 to 31.5 in. (60 to 80 cm) off the ground, and capable of
supporting approximately 242 pounds (110 kg).
21.4 in.
(54.3 cm)
26.1 in.
(66.3 cm)
Approx. 31.5 in.
(80 cm)
Approx. 57.1 in. (145 cm)*
Approx. 39.4 in.
(100 cm)
0.4 in.
(1 cm)
* Approx. 59.1 in. (150 cm) with optional L-size hanger platen.
Unpack and Place Printer
1
Make sure you have these items:
Maintenance kit
Limited
warranty
Medium platen
and hoop
Waste ink
bottle holder
Rear cover
Waste ink bottle
Ink labels
Grip pad tool
Ink packs/maintenance liquid
Tube/cable clamps
Printer
Ink charging unit
Waste ink tube
Grip pad
Note:
See the online
User's Guide
for information on installing the grip pad,
using the grip pad tool, and using the maintenance kit and tweezers.
2
Remove all the packaging materials and tape. Check carefully for all the
tape inside and outside the printer and platen.
WARNING:
The printer requires four people to lift and move it. Make sure to
grip the printer where indicated by the gray stickers and * marks as shown
in the illustration. The * marks denote non-slip pads under the printer where
hands should be placed. All four people should lift simultaneously to avoid
tilting the printer and trapping their hands.
Assemble the Printer
1
Make sure any protective material is removed from the back of the
printer.
2
Holding a wipe to the waste ink outlets, remove the plugs on the back
of the printer and then wipe the waste ink outlets as shown.
Note:
Do not throw the plugs away; you need them if you transport the
printer.
3
Connect the waste ink tube. Make sure that the longer end of the tube
is connected to the waste ink outlet on the left side and the shorter end
is connected to the waste ink outlet on the right side.
4
Attach the rear cover as shown.
0.4 in.
(1 cm)
Tweezers
Power cord
Zip ties
Caution label
Wipes