Epson SureColor S50670 Production Edition Product Update
Epson SureColor S50670 Production Edition Manual
 |
View all Epson SureColor S50670 Production Edition manuals
Add to My Manuals
Save this manual to your list of manuals |
Epson SureColor S50670 Production Edition manual content summary:
- Epson SureColor S50670 Production Edition | Product Update - Page 1
and paper misalignment when you use the auto take-up reel: • Tensioner media guides • Paper tape (non-adhesive), which ensures accurate media winding and saves media tape to the back of the roll core. Note: when the tensioner media guides are not in use, slide them to the edges of the tension bar. - Epson SureColor S50670 Production Edition | Product Update - Page 2
Español Actualización Su impresora incluye dos accesorios diseñados para prevenir golpes del cabezal y desalineación del material de impresión cuando se utiliza el rodillo de recogida automática. • Guías de papel del tensor • Cinta de papel (sin adhesivo), que asegura el enrollamiento correcto y - Epson SureColor S50670 Production Edition | Product Update - Page 3
Português Atualização A sua impressora inclui dois acessórios criados para prevenir batidas da cabeçote e desalinhamento do papel quando usar a unidade de enrolamento automático: • Guias de papel do tensor • Fita de papel (não adesiva), que garante o enrolamento correto e economiza papel 2. Corte - Epson SureColor S50670 Production Edition | Product Update - Page 4
CPD-40082 © 2013 Epson America, Inc., 8/13 Printed in USA Impreso en: USA País de impressão: USA
-
1 -
2 -
3 -
4
 |
 |
Epson
®
SureColor
®
S-Series
Product Update
Your printer includes two accessories designed to prevent head strikes
and paper misalignment when you use the auto take-up reel:
•
Tensioner media guides
•
Paper tape (non-adhesive), which ensures accurate media winding
and saves media
Using the Tensioner Media Guides
After media is loaded in the printer and auto take-up reel, place the
tensioner media guides on the tension bar. They should lightly touch
the edges of the media, without pressure.
Note:
when the tensioner media guides are not in use, slide them
to the edges of the tension bar.
Using the Paper Tape
Use the paper tape to attach media to the auto take-up reel core. This
allows the media to “self-center,” preventing skew and head strike
issues. You can use the paper tape included with the printer or any
paper tape that resists tearing and stretching.
Note:
Epson recommends using a roll core that is wider than the
media you are printing on. This may help keep the edges of the
media on the core as it is rolled up.
1.
After media is loaded in the printer, do the following:
•
Grasp the center of the media edge and pull it straight down.
•
Pull the media down until the leading edge reaches the upper
label on the after heater.
2.
Cut off about 24 inches (60 cm) of paper tape and attach it to the
media using adhesive tape.
3.
Trim the corners of the media, leaving a straight section at the
center about 4 to 8 inches (10 to 20 cm) wide.
4.
Feed the media by pressing the
button, until the leading edge
of the paper tape reaches the roll core on the auto take-up reel.
5.
Attach the paper tape to the roll core using adhesive tape. If you
want to take up media with the printed side facing in, attach the
paper tape to the back of the roll core.
6.
Set the
Auto
switch on the auto take-up reel according to the way
you want to wind the paper:
•
Printed side out:
•
Printed side in:
7.
Gently lower the tension bar. Make sure the paper tape does not
come off.
8.
Position the tensioner media guides after the media reaches the
tension bar.
English
4-8 in. (10-20 cm)