Epson WorkForce WF-7820 Start Here - Installation Guide

Epson WorkForce WF-7820 Manual

Epson WorkForce WF-7820 manual content summary:

  • Epson WorkForce WF-7820 | Start Here - Installation Guide - Page 1
    WF-7820/WF-7840 Start Here IMPORTANT: Before using this product, make sure you read these instructions and the safety instructions in the online User's Guide. Note: This printer is designed for use with Epson® cartridges only, not third-party cartridges or ink. For important ink information, visit
  • Epson WorkForce WF-7820 | Start Here - Installation Guide - Page 2
    down into place. 2 Slide the side edge guides all the way out and set the front edge guide to the paper size you are using. 3  printer or raise the scanner unit while the printer is charging or you'll waste ink. Note: As part of setup, your product's serial number will be sent to a secure Epson
  • Epson WorkForce WF-7820 | Start Here - Installation Guide - Page 3
    the latest software, visit: WF-7820 www.epson.com/support/wf7820 (U.S.) www.epson.ca/support/wf7820 (Canada) WF-7840 www.epson.com/support/wf7840 (U.S.) www.epson.ca/support/wf7840 (Canada) 3 Follow the instructions on the computer screen to run the setup program. Any problems? Network setup was
  • Epson WorkForce WF-7820 | Start Here - Installation Guide - Page 4
    program for end-of-life hardware and ink cartridges. Please go to www.epson.com/recycle (U.S.) or www.epson.ca/recycle (Canada) for information on how to return your products for proper disposal. WF-7820/WF-7840 replacement ink cartridges Color Black Standard-capacity High-capacity Extra
  • 1
  • 2
  • 3
  • 4

Start Here
IMPORTANT:
Before using this product, make sure you read
these instructions and the safety instructions in the online
User’s
Guide
.
Note:
This printer is designed for use with Epson
®
cartridges only, not
third-party cartridges or ink. For important ink information, visit
www.epson.com/epsonink
(U.S.) or
www.epson.ca/epsonink
(Canada)
or see your printer box.
Important Safety Instructions:
When using telephone equipment, you
should always follow basic safety precautions to reduce the risk of fire,
electric shock, and personal injury, including the following:
• Do not use the Epson product near water.
• Always keep this guide handy.
• Avoid using a telephone during an electrical storm. There may be a
remote risk of electric shock from lightning.
• Do not use a telephone to report a gas leak in the vicinity of the leak.
Caution:
To reduce the risk of fire, use only a No. 26 AWG or larger
telecommunication line cord.
The illustrations show the WF-7840, but the steps are the same
for the WF-7820, unless otherwise specified.
1
Unpack
Note:
Do not open the ink cartridge packages until you are ready to
install the ink. Cartridges are vacuum packed to maintain reliability.
1
Remove all protective materials from the product.
2
Lift up the scanner unit until it locks into place and remove
all protective materials from inside the product.
Caution:
Do not touch the flat white cable.
3
Lower the scanner unit.
2
Turn on and configure
1
Connect the power cord to the back of the product and to
an electrical outlet.
Caution:
Do not connect to your computer yet.
2
Raise the control panel and turn on the product.
Note:
If an error code appears, turn off the product and
check that no protective material has been left inside the
product.
3
Select your language, country, date, and time on the
LCD screen.
Note:
You can change these settings later using the product’s
control panel. For more information, see the online
User’s Guide
.
3
Install ink cartridges
Caution:
Keep the ink cartridges out the reach of children and do not
drink the ink.
Note:
The included initial cartridges are designed for reliable printer
setup and cannot be used as replacement cartridges or resold. After
setup, the remaining ink is available for printing.
1
Lift up the scanner unit until it locks into place, then
open the ink cartridge cover.
Caution:
Do not touch the flat white cable.
WF-7820/WF-7840