Fantec DB-R35DUS-2 Datasheet
Fantec DB-R35DUS-2 Manual
 |
View all Fantec DB-R35DUS-2 manuals
Add to My Manuals
Save this manual to your list of manuals |
Fantec DB-R35DUS-2 manual content summary:
- Fantec DB-R35DUS-2 | Datasheet - Page 1
DB-R35DUS User Manual English - Fantec DB-R35DUS-2 | Datasheet - Page 2
Detail View: Front View: 1. Power indicator 2. Rebuild indicator 3. HDD1 Access Indicator 4. HDD2 Access Indicator 5. HDD1 Error Indicator 6. HDD2 Error Indicator 7. Ventilation USB 2.0 Rare View: 1. Power switch 2. Power receptacle 3. USB 2.0 port 4. Fan for ventilation - Fantec DB-R35DUS-2 | Datasheet - Page 3
usage, please install one main source HDD and power "on" DB-R35DUS. Wait until "error" indicator on the second HDD lights on, system had set first HDD to Main HDD then power "off" DB-R35DUS. Please install second HDD and power "on" again. System will automatically "rebuild - Fantec DB-R35DUS-2 | Datasheet - Page 4
System Requirements PC Requirements • Minimum Intel Pentium III CPU 500MHz, 128MB RAM • USB 1.1 equipped PC; Win2000, WinXP, Vista • USB 2.0 equipped PC; Win2000, WinXP, Vista Mac Requirements • Minimum Apple G3 processor (G4 for 1394b), 128MB RAM • USB 1.1 equipped Mac; Mac OS 9.2, 10.1.5 or above - Fantec DB-R35DUS-2 | Datasheet - Page 5
Hard Drive Assembly: 1. To remove the cover of DB-R35DUS: Please unscrew and remove the screws on the bottom of unit. Only one side (top) of screws needs to remove. Top side is the side - Fantec DB-R35DUS-2 | Datasheet - Page 6
5. Push forward the HDD holder to secure the connection and fasten the screws on the holder. 6. Recover the top plate of DB-R35DUS and fasten the screws prior remove. Now installation is complete, please attach power core and connect DB-R35DUS with USB cable to computers. DB-R35DUS is ready to use. - Fantec DB-R35DUS-2 | Datasheet - Page 7
HDD which contain data. And fasten with screws. 3-2. Insert back the HDD holder back to DB-R35DUS with first HDDs attached. Make sure the connection of HDD holder and DB-R35DUS is intact. At this point, please connect DB-R35DUS to power source and turn on the unit. (no need to connect to computer - Fantec DB-R35DUS-2 | Datasheet - Page 8
secure it with screws. 3-4. Push forward the HDD holder to secure the connection and fasten the screws on the holder. 3-5. Recover the top plate of DB-R35DUS and fasten the screws prior remove. Now installation is complete, please attach power core. After turn on the unit - Fantec DB-R35DUS-2 | Datasheet - Page 9
System Setup: Connection to your computer: Few cautions before using RAID enclosure 1. Do not cover or block the ventilation holes on the enclosure. 2. Check for visible damage on unit, accessories and cables before tuning on the power. 3. Do not expose the enclosure to water and humid conditions. - Fantec DB-R35DUS-2 | Datasheet - Page 10
RAID0 - Stripping: Two HDDs will show up as one large single drive but speed performance will boost up. The two HDDs will write Data in "column" effect. This form of array splits each piece of Data across both HDDs in segments. Data are store between first HDD and second HDD. While the HDD is stripe - Fantec DB-R35DUS-2 | Datasheet - Page 11
the setting please refer to Hard Drive Assembly for correctly way of setting. 1. Turn on PC and start Windows. 2. Connect (USB or 1394) DB-R35DUS and turn on the power. 3. Windows will search and install drive automatically. 4. Open "My Computer" and "external hard drive" will appear. Remove the - Fantec DB-R35DUS-2 | Datasheet - Page 12
. Remove the "external hard drive" from Macintosh.. 1. Drag the external hard drive to trash bin. 2. Turn off the power. Note: If user wishes to use DB-R35DUS on both Windows and Mac OS system, we recommend that HDD to be formatted at FAT32. Also, please do the formatting under Windows OS. If
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
 |
 |
DB-R35DUS
User Manual
English