Fisher and Paykel DG70FA1 DG08/09 DG70 Gas Dryer Install (English)
Fisher and Paykel DG70FA1 Manual
 |
View all Fisher and Paykel DG70FA1 manuals
Add to My Manuals
Save this manual to your list of manuals |
Fisher and Paykel DG70FA1 manual content summary:
- Fisher and Paykel DG70FA1 | DG08/09 DG70 Gas Dryer Install (English) - Page 1
Be sure to leave these instructions with the consumer. Note to Consumer - Keep these instructions with your Owner's Manual for future reference. A WARNING a barrier from vehicles. Important • This dryer must be exhausted to the outdoors. • Service information and wiring diagram located in control - Fisher and Paykel DG70FA1 | DG08/09 DG70 Gas Dryer Install (English) - Page 2
that the tab portion is at the bottom of the duct. BLOWER HOUSING 8 5/8" CUT PORTION TAB OPENING -- Only metal duct may be used inside the dryer cabinet 11 1/4" NEM 04 O 4 3/4" NOTE: To secure the duct, insert the tab (located on the appliance base) in the opening and bend it. 5. Detach and - Fisher and Paykel DG70FA1 | DG08/09 DG70 Gas Dryer Install (English) - Page 3
30 Feet 20 Feet 10 Feet 15 Feet 10 Feet Parts Available from Local Service Organization • Rigid Metal Duct Components 4" X 1' Duct 4" X 2' Duct avoid leaks. The male end of each section of duct must point away from the dryer. • Do not assemble the duct work with fasteners that extend into the duct. - Fisher and Paykel DG70FA1 | DG08/09 DG70 Gas Dryer Install (English) - Page 4
is equipped with a Valve & Burner Assembly for use only with natural gas. Using a separate conversion kit, your local Service organization can convert this dryer for use with gases listed on the rating plate. ALL CONVERSIONS MUST BE MADE BY PROPERLY TRAINED AND QUALIFIED PERSONNEL AND IN ACCORDANCE - Fisher and Paykel DG70FA1 | DG08/09 DG70 Gas Dryer Install (English) - Page 5
. Bathroom or Bedroom Installation • The dryer MUST be exhausted to the outdoors. See EXHAUST INFORMATION section. • The installation must conform with the local codes, or in the absence of local codes, with the National Fuel Gas Code, ANSI Z223. SERVICING: A CAUTION: Consideration must be given - Fisher and Paykel DG70FA1 | DG08/09 DG70 Gas Dryer Install (English) - Page 6
Installation Instructions If all rigid metal duct cannot be used, then flexible all metal venting can be used, but it will reduce the maximum recommended duct length. In special installations when it is impossible to make a connection with the above recommendations, then UL listed clothes dryer
-
1 -
2 -
3 -
4 -
5 -
6
 |
 |
Installat►on
►nstruct►ons
for
your
new
Gas
Dryer
Before
you
begin
-
Read
these
instructions
completely
and
carefully.
IMPORTANT
-
Save
these
instructions
for
local
inspector's
use.
IMPORTANT
-
OBSERVE
ALL
GOVERNING
CODES
AND
ORDINANCES.
Note
to
Installer
-
Be
sure
to
leave
these
instructions
with
the
consumer.
Note
to
Consumer
-
Keep
these
instructions
with
your
Owner's
Manual
for
future
reference.
A
WARNING
-
POTENTIAL
FIRE
AND
SHOCK
HAZARD
•
Use
only
rigid
metal
or
fl
exible
metal
4"
diameter
ductwork
for
exhausting
to
the
outdoors.
Never
use
plastic
or
other
combustible
ductwork.
•
This
appliance
must
be
properly
grounded
and
installed
as
described
in
these
instructions.
•
Do
not
install
or
store
appliance
in
an
area
where
it
will
be
exposed
to
water/weather.
•
The
National
Fuel
Gas
Code
restricts
installations
of
gas
appliances
in
garages.
They
must
be
18"
off
the
ground
and
protected
by
a
barrier
from
vehicles.
Important
•
This
dryer
must
be
exhausted
to
the
outdoors.
•
Service
information
and
wiring
diagram
located
in
control
console.
Tools
you
will
need
Slip
joint
pliers
Screwdriver
Step
1
Remove
and
save
literature
and
parts
package
from
dryer
drum.
Step
2
Lay
carton
corner
post
or
two
2"x4"
boards
on
the
fl
oor.
Lay
dryer
on
its
back.
Step
3
Remove
foam
shipping
pads
by
pulling
at
sides
and
breaking
away
from
dryer
legs.
Be
sure
to
remove
all
foam
pieces
from
around
legs.
FOAM
SHIPPING
PADS
Step
4
Stand
dryer
upright.
Installation
Step
5
Move
dryer
to
desired
operating
location.
PULL
HERE
TO
SEPARATE
FROM
FRONT
LEG
DRYER
LEGS
PULL
HERE
TO
SEPARATE
FROM
REAR
LEG
Step
6
Adjust
leveling
legs
to
match
washer
height.
Dryer
must
be
level
and
rest
firmly
on
all
four
leveling
legs.
Step
7
Connect
gas
supply.
(See
GAS
CONNECTION
INFORMATION
section
of
this
instruction.)
Step
8
Connect
to
power
supply.
(See
ELECTRICAL
CONNECTION
INFORMATION
section
of
this
instruction.)
Step
9
Connect
external
exhaust
.
(See
EXHAUST
INFORMATION
section
of
this
instruction.)
•
Check
for
proper
operation.
Step
10
Place
Owner's
Manual
and
Installation
Instructions
in
a
location
where
they
may
be
found
by
the
customer.
nn
o7Dni