Frigidaire FASG7074LW Installation Instructions (All Languages)
Frigidaire FASG7074LW Manual
![]() |
UPC - 012505382642
View all Frigidaire FASG7074LW manuals
Add to My Manuals
Save this manual to your list of manuals |
Frigidaire FASG7074LW manual content summary:
- Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 1
All about the Installation of your Dryer TABLE OF CONTENTS Important Safety Instructions 2-3 Reversing Door 18-21 Installation Requirements 4-10 Accessories 22 Installed Dryer Dimensions 11 Français 23 Installation Instructions 12-17 Español 45 137336500A (1003) - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 2
The instructions in this manual and all other literature included with this dryer are not meant to cover every possible condition and situation that may occur. Good safe practice and caution MUST be applied when installing, operating and maintaining any appliance. WHAT TO DO IF YOU SMELL GAS: • Do - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 3
240v Electric Supply (Electric Dryer) Approved NEMA 10-30R or 14-30R service cord with all screws tight on terminal block Approved strain relief installed Terminal access cover installed before initial operation Door Reversal Follow detailed instructions in this guide Test hinge and latch - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 4
this dryer with power created by gas powered dryer is internally grounded to neutral unless it was manufactured for sale in Canada. Only a 4-conductor cord shall be used when the appliance marked for use with clothes dryers. For 3-wire cord connection instructions see ELECTRICAL CONNECTIONS FOR A - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 5
kPa). 7 The dryer MUST be isolated from the gas supply piping system during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig (3.45 kPa). 8 Connections for the gas supply must comply with the Standard for Connectors for Gas Appliances, ANSI Z21.24 - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 6
or any other obstruction. WARNING FIRE HAZARD Failure to follow these instructions can create excessive drying times and fire hazards. The following are obstruct clothes dryer airflow and increase the risk of fire. If your present system is made up of plastic duct or metal foil duct, replace it with - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 7
will be expelled into the laundry area. An accumulation of lint in any area of the home can create a health and fire hazard. The dryer must be connected to an exhaust outdoors. Regularly inspect the outdoor exhaust opening and remove any accumulation of lint around the outdoor exhaust opening and - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 8
Exhaust direction Directional exhausting can be accomplished by installing a quick-turn 90° dryer vent elbow directly to exhaust outlet of dryer. Dryer vent elbows are available through your local parts distributor or hardware store. CORRECT INCORRECT In installations where the exhaust system is - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 9
Part 280) or Standard CAN/CSAZ240 MH. 2 Dryer MUST be exhausted outside (outdoors, not beneath the mobile home) using metal ducting that will not support to previous sections in this guide for other important exhaust venting system requirements. 5 When installing a gas dryer into a mobile home, a - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 10
or closet, MUST be exhausted outdoors. 2 No other fuel burning appliance shall be installed in the same closet as the gas dryer. 3 Your dryer needs the space around it for proper ventilation. DO NOT install your dryer in a closet with a solid door. 4 Closet door ventilation required: A minimum - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 11
) to installation depth. Downward venting of exhaust on pedestal-mounted dryer adds approximately 2.25 in. (5.7 cm) to installation depth. 51.4" (131cm) to clear open door 30.3" (77cm)* to front of closed door gas supply pipe on rear of gas unit 1.6" (4cm) 16.9" (43cm) 3.75" (9.5cm) 13.50" (34 - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 12
can create electrical shock and/or a fire hazard. WARNING ELECTRICAL SHOCK HAZARD • This appliance MUST be properly grounded. Electrical shock can result if the dryer is not properly grounded. Follow the instructions in this manual for proper grounding. • Do not use an extension cord with this - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 13
a licensed electrician. 3 DO NOT modify the plug provided with this appliance. If it will not fit the outlet, have a proper outlet installed by a qualified electrician. Grounding requirements - Gas dryer (USA and Canada) 1 The dryer is equipped with a three-prong (grounding) plug for your protection - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 14
INSTALLATION INSTRUCTIONS Gas connection 1 Remove the shipping cap from gas pipe at the rear of the dryer. IMPORTANT DO NOT connect the dryer to L.P. gas service without converting the gas valve. An L.P. conversion kit must be installed by a qualified gas technician. 2 Connect a 1/2 inch (1.27 cm) - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 15
the screw securing the terminal block access cover in the lower corner on the back of the dryer. 3 Install a UL-approved strain relief according to the power cord/strain relief manufacturer's instructions in the power cord entry hole below the access panel. At this time, the strain relief should - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 16
on the back of the dryer. 3 Install a UL-approved strain relief according to the power cord/strain relief manufacturer's instructions in the power cord entry on the terminal block. Tighten the screw securely. 8 Attach the RED and BLACK power cord conductors to the outer, BRASS colored terminals on - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 17
time and money. 6 If you have any questions during initial operation, please review the "Avoid Service Checklist" in your Use & Care Guide before calling for service. 7 Place these instructions in a location near the dryer for future reference. Í NOTE A wiring diagram and technical data sheet are - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 18
then upper screw. 4 Gently place dryer door face down on flat, covered work surface. 5 Locate the 5 indented head screws (no. 1-5) in the small, circular recesses (at 11, 1, 4, 6, and 8 o'clock positions) of the inner door. Remove and save these 5 screws. 3 Supporting door with both hands, squarely - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 19
Reversing the hinge 1 Carefully pull out the 2 small round hole plugs from the front panel and save. Remove and save the square "T" slot cover by sliding it up and pulling it out. Move all 3 plugs to the opposite side of the front panel and insert. ROUND PLUG REVERSING DOOR 4 From the back side of - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 20
-hand hinge. 3 Replace indented head screws (no. 1-5) removed earlier. Take care not to strip out the plastic holes. 4 Replace pan head screws (no on the supports for the hinge cutout cover. Pivot the inner door down onto the outer door. 5 Locate new metal strike supplied with dryer manuals. Grip - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 21
holes. "T" POST ON DOOR HINGE "T" SLOT IN FRONT PANEL REVERSING DOOR 3 Close the door and test operation of hinge, strike and latch. 2 While supporting the door, install the upper pan head screw first and then the lower one. Í NOTE Correctly installed hinge screws will press hinge flush to front - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 22
Classic Red Touch Up Pen - P/N 5304471227 Classic Blue Touch Up Pen - P/N 5304471229 Classic Silver Touch Up Pen - P/N 5304471228 Classic Black Touch Up Pen - P/N 5304458932 *Other colors may be available. Contact the source where you purchased your dryer. Replacement parts: If replacements parts - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 23
Tout à propos de Installation de votre Sécheuse TABLE DES MATIÈRES Mesures de sécurité importantes 24-25 Instructions d'installation 34-39 Exigences d'installation 26-32 Inversion de la porte 40-43 Dimensions, appareil install 33 Accessoires 44 - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 24
service ou le fournisseur de gaz. • Installez l'appareil conformément aux instructions glements locaux ainsi qu'à la toute dernière édition du Fuel Gas Code (ANSI Z223.1), ou au Canada, au CAN/ACG B149.1- autre laveuse. • Les instructions comprises dans ce guide et toute autre documentation fournie - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 25
certifié est installé Le couvre-borne est installé avant la première mise en marche Inversion de la porte Suivez les instructions détaillées contenues dans ce guide Vérifiez que la charnière et le loquet fonctionnent correctement Alimentation en électricité Le système électrique de la maison - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 26
toute autre source d'alimentation différente de celle fournie par les services publics n'est pas recommandée. Exigences électriques de la sécheuse spécialement indiqués pour une utilisation avec une sécheuse. Pour les instructions de raccordement du cordon à 3 fils, consultez la section CONNEXIONS É - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 27
canalisation de gaz à des pressions égales ou inférieures à 3,45 kPa (1/2 lb/po2). 8 Les branchements d'alimentation en gaz doivent être conformes à la norme Connectors for Gas Appliances (Raccords pour appareils au gaz) ANSI Z21.24. 27 - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 28
po) entre le bas de la bouche d'évacuation et le sol ou toute autre obstruction. AVERTISSEMENT RISQUE D'INCENDIE Le non-respect de ces instructions pourrait augmenter démesurément les temps de séchage et entraîner des risques d'incendie. Vous trouverez ci-dessous les exigences pour l'utilisation ad - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 29
EXIGENCES D'INSTALLATION Exigences de système d'évacuation (suite) AVERTISSEMENT RISQUE D'INCENDIE Une sécheuse doit être évacuée vers l'extérieur. N'évacuez pas une sécheuse dans une cheminée, un mur, un plafond, un grenier, un vide sanitaire ou dans tout espace clos d'un bâtiment. La sécheuse - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 30
EXIGENCES D'INSTALLATION Exigences de système d'évacuation (suite) Installez les raccords mâles dans le bon sens : Direction d'évacuation Il est possible de diriger l'évacuation en posant un coude de 90° à courbe immédiate directement à la sortie d'évacuation de la sécheuse. Les coudes pour é - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 31
à l'extérieur de la cloison et être fixé solidement à la structure de la maison. 4 Reportez-vous aux sections précédentes de ce guide relativement aux autres exigences d'évacuation importantes. 5 Lors de l'installation d'une sécheuse à gaz dans une maison mobile, des dispositions doivent être prises - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 32
EXIGENCES D'INSTALLATION Exigences de dégagement (suite) Installation dans un Endroit en Retrait ou une Armoire 1 Une sécheuse installée dans une chambre à coucher, une salle de bains, un renfoncement ou un placard DOIT être évacuée vers l'extérieur. 2 Aucun autre appareil à combustion ne doit ê - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 33
51.4" (131cm) Avec la porte grande ouverte DIMENSIONS DE L'INSTALLATION DE SÉCHEUSE 30.3" (77cm)* À partir de l'avant de la porte lorsqu'elle est fermée 27.0" (68.5cm) 36.0" (91.5cm) 51.25" (130cm) Sécheuse autonome sur le plancher Plancher Alimentation en gaz à l'arrière de l'appareil à gaz - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 34
équatement mis à la terre. La mise à la terre inadéquate de la sécheuse pourrait entraîner des risques de choc électrique. Suivez les instructions de ce guide pour une mise à la terre adéquate. • N'utilisez pas de rallonge avec cet appareil. Certains cordons prolongateurs ne sont pas conçus pour la - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 35
INSTRUCTIONS D'INSTALLATION Exigences de mise à la terre - Sécheuse électrique (Canada) AVERTISSEMENT RISQUE DE CHOC ÉLECTRIQUE Un raccordement inadéquat du conducteur de mise à la terre de l'é - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 36
INSTRUCTIONS D'INSTALLATION Connexion de gaz 1 Retirez le capuchon d'expédition de la conduite de gaz à l'arrière de l'appareil. IMPORTANT NE RACCORDEZ PAS la sécheuse à une - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 37
le couvercle d'accès du bornier dans le coin inférieur du dos de la sécheuse. 3 Installez un réducteur de tension certifié UL conformément aux instructions du fabricant de cordon d'alimentation ou de réducteur de tension dans l'orifice de cordon d'alimentation sous le panneau d'accès. À ce moment, le - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 38
le couvercle d'accès du bornier dans le coin inférieur du dos de la sécheuse. 3 Installez un réducteur de tension certifié UL conformément aux instructions du fabricant de cordon d'alimentation ou de réducteur de tension dans l'orifice de cordon d'alimentation sous le panneau d'accès. À ce moment, le - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 39
à l'utilisation initiale, veuillez vous reporter à la section « Liste de vérification » de votre Guide d'utilisation et d'entretien avant d'effectuer une demande de service. 7 Laissez ces instructions à proximité de la sécheuse pour vous y reporter ultérieurement. Í REMARQUE Un schéma électrique - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 40
INVERSION DE LA PORTE Dépose de la porte 1 Protégez la surface de travail, comme le dessus de la sécheuse ou le plancher près de la sécheuse, avec un chiffon doux ou une serviette. 2 Ouvrez la porte de la sécheuse et retirez les deux vis de la charnière. Enlevez d'abord la vis du bas, puis la vis du - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 41
Inversion de la charnière 1 Enlevez délicatement les 2 petits bouchons circulaires qui se trouvent sur le panneau avant et conservezles. Retirez le protecteur carré de la fente en « T » en le faisant glisser vers le haut et en le tirant vers l'extérieur, puis conservez-le. Ensuite, insérez les 3 - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 42
filet des trous en plastique. nos 1 à 5 nos 6 et 7 2 Déposez l'ouverture de la partie interne de la porte dans un angle de 90 degrés sur les supports de la découpe de la charnière. Ensuite, faites pivoter la partie interne de la porte dans la partie externe. 5 Repérez la nouvelle gâche - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 43
Remise en place de la porte 1 En tenant la porte à deux mains, insérez complètement la tige en « T » située à l'arrière de la charnière dans la fente en « T » se trouvant dans le panneau avant. Ensuite, baissez la porte de sorte que les trous de montage soient alignés. TIGE EN « T » DE LA CHARNIÈRE - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 44
devez commander des pièces de rechange pour votre sécheuse, communiquez avec le marchand qui vous a vendu votre appareil, ou reportez-vous au guide d'utilisation et d'entretien pour obtenir plus de détails. 44 AVERTISSEMENT RISQUE ÉLECTRIQUE Étiquetez tous les fils avant de les débrancher pendant - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 45
Instrucciones de instalación 56-61 Requisitos de instalación 48-54 Inversión de la puerta 62-65 Dimensiones de la secadora instalada 55 Accesorios 66 www.frigidaire.com UEES.AU1U-8.10-08-0904-49-4940-494044 wwwww.fwrig.firdigaidrea.icrea.caCanCaadnaad1á-810-08-0206-52-6853-582352 45 - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 46
a cabo por un instalador calificado, agencia de servicios o proveedor de gas. • Instale la secadora de ropa de acuerdo con las instrucciones del fabricante Código Eléctrico de Canadá (Canadian Electrical Code) Parte 1. • El servicio de gas de la secadora debe cumplir con los códigos y las ordenanzas locales, - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 47
á nivelada de lado a lado y de adelante hacia atrás El secadora descansa firmemente sobre sus cuatro esquinas Suministro de gas (secadora a gas) Válvula de cierre manual instalada en la tubería de suministro Todas las conexiones selladas con un sellante aprobado y bien apretadas con una llave - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 48
DE INSTALACIÓN Í NOTA Debido a posibles variaciones en el voltaje, no se recomienda utilizar esta secadora con electricidad generada a partir de generadores a gas, solares, eólicos ni de ninguna otra clase que no sean los empleados por su empresa de electricidad local. Requisitos eléctricos de la - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 49
instalación DEBE realizarse de acuerdo con los códigos locales o, en ausencia de ellos, con el Código de Gas Nacional (National Fuel Gas Code), ANSI Z223.1 (última edición). 2 La línea de suministro de gas debe ser un tubo de 1,27 cm (1/2 pulgada). 3 Si los códigos lo permiten, se puede utilizar un - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 50
REQUISITOS DE INSTALACIÓN Requisitos del sistema de escape Utilice solo un conducto de metal flexible o rígido de 102 mm (4 pulgadas) de diámetro (mínimo) y una capucha de ventilación aprobada que tenga uno o más reguladores de tiro que se abran cuando la secadora esté en funcionamiento. Cuando la - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 51
utilice tornillos, remaches ni otros sujetadores que se extiendan hacia la parte interna del conducto para ensamblarlo. Es posible que la pelusa quede el filtro, los tornillos o los remaches, lo que puede obstruir la red de conductos y constituir un peligro de incendio, así como también aumentar - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 52
ón vertical del sistema de escape es aceptable, ciertas circunstancias atenuantes podrían afectar el funcionamiento de la secadora: • Sólo se debe utilizar una red de conductos de metal rígido. • Si la ventilación se efectúa en forma vertical a través del techo, es posible que el sistema de escape - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 53
Norma de Seguridad y Construcción de Casas Rodantes, título 24 CFR, Parte 32-80 (que anteriormente se conocía como la Norma Federal de Seguridad las secciones anteriores de esta guía. 5 Cuando se instale una secadora a gas en una casa rodante, se debe dejar espacio en el exterior para la salida - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 54
ún otro artefacto de combustión en el mismo armario que la secadora a gas. 3 La secadora necesita espacio a su alrededor para que la ventilación sea ficie. ESPACIOS MÍNIMOS PARA LA INSTALACIÓN: cm (pulgadas) LATERALES PARTE TRASERA PARTE PARTE SUPERIOR DELANTERA Alcôve 0 cm (0") 0 cm (0") 0 cm - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 55
.5cm) 36.0" (91.5cm) secadora independiente sobre el piso línea del piso 51.25" (130cm) tubería de suministro de gas en la parte trasera de la unidad de gas 1.6" (4cm) secadora colocada sobre pedestal opcional línea del piso * Para obtener estas dimensiones mínimas de profundidad, la secadora - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 56
INSTRUCCIONES DE INSTALACIÓN Instalación eléctrica Los siguientes son requisitos necesarios para la instalación eléctrica segura y correcta de su secadora. El no seguir estas instrucciones puede producir una descarga eléctrica y/o incendio. ADVERTENCIA PELIGRO DE DESCARGA ELÉCTRICA • Este - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 57
Si no calza en el tomacorrientes, pídale a un electricista calificado que instale un tomacorrientes adecuado. Requisitos de conexión a tierra: secadora a gas (Estados Unidos y Canadá) 1 La secadora está equipada con un enchufe de tres patas (conexión a tierra) para evitar el peligro de electrocuci - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 58
de los gases licuados en todas las conexiones de los tubos. FLUJO DE GAS Válvula de cierre manual Conector doble Conector doble Cerrado Conector Abierto Conector flexible Tubo de admisión en la parte posterior de la secadora Todas las conexiones deben estar ajustadas con llave IMPORTANTE - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 59
del tomacorriente. 2 Extraiga el tornillo que sujeta la cubierta de acceso del bloque terminal que se encuentra en la esquina inferior de la parte trasera de la secadora. 3 Instale un dispositivo de liberación de tensión aprobado por U.L., de acuerdo con las instrucciones relativas al cable de - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 60
del tomacorriente. 2 Extraiga el tornillo que sujeta la cubierta de acceso del bloque terminal que se encuentra en la esquina inferior de la parte trasera de la secadora. 3 Instale un dispositivo de liberación de tensión aprobado por U.L., de acuerdo con las instrucciones relativas al cable de - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 61
cuidadosamente. Ajuste una o varias de las patas de la secadora hasta que se encuentre firme sobre las cuatro patas. Coloque un nivel en la parte superior A de la secadora. La secadora DEBE estar nivelada y firme sobre las cuatro patas. Presione las distintas esquinas para asegurarse de que la - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 62
INVERSIÓN DE LA PUERTA Cómo extraer la puerta 1 Proteja las superficies de trabajo planas, como la parte superior de la secadora o el piso cerca de ésta utilizando un paño o toalla suave. 2 Abra la puerta de la secadora y retire los dos tornillos de - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 63
de ella para retirarla. Mueva los 3 tapones al lado opuesto del panel delantero. TAPÓN REDONDO TAPÓN CUADRADO INVERSIÓN DE LA PUERTA 4 Desde la parte trasera de la puerta interior, presione las lengüetas de retención del tapón de plástico cuadrado para liberarlo. Guarde el tapón cuadrado para - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 64
de la cubierta de la bisagra. Gire la puerta interior hacia abajo sobre la puerta exterior. 5 Ubique el nuevo pestillo de metal proporcionado con los manuales de la secadora. Sostenga el pestillo nuevo con alicates como se muestra abajo. Inserte firmemente el pestillo de manera que quede en posici - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 65
Reinstalación de la puerta 1 Mientras sostiene la puerta con ambas manos, introduzca la pieza en forma de "T" que se encuentra en la parte trasera de la bisagra en la ranura en forma de "T" del panel delantero y baje la puerta para alinear los agujeros de instalación. PIEZA EN FORMA - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 66
que adquirió no incluye un kit de instalación sobre la lavadora o desea un kit diferente, puede pedir uno. KIT DE CONVERSIÓN A GAS LP Pieza No.. PCK4200 Las secadoras a gas diseñadas para el uso en lugares con suministro de LP requieren utilizar un kit de conversión antes de la instalación. KIT DE - Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 67
- Frigidaire FASG7074LW | Installation Instructions (All Languages) - Page 68
![](/manual_guide/products/frigidaire-fasg7074la-installation-instructions-languages-672659d/1.png)
All about the
Installation
of your
Dryer
137336500A (1003)
TABLE OF CONTENTS
Important Safety Instructions
..............................
2-3
Installation Requirements
.................................
4-10
Installed Dryer Dimensions
..................................
11
Installation Instructions
..................................
12-17
Reversing Door
..............................................
18-21
Accessories
.........................................................
22
Français
..............................................................
23
Español
..............................................................
45