Frigidaire FFRE0633Q1 Installation Instructions
Frigidaire FFRE0633Q1 Manual
 |
View all Frigidaire FFRE0633Q1 manuals
Add to My Manuals
Save this manual to your list of manuals |
Frigidaire FFRE0633Q1 manual content summary:
- Frigidaire FFRE0633Q1 | Installation Instructions - Page 1
where air conditioner will be installed. Be sure it will support the weight of the unit overan extended period of time. Handle air conditioner with care. Make sure air conditioner does not fall during installation. NOTE: Mounting Hardware Qty. SAVE CARTON and these INSTALLATION INSTRUCTIONS for - Frigidaire FFRE0633Q1 | Installation Instructions - Page 2
FIG. 3. D. Slide the panel all the way in and repeat on the other side. FIG. 1 FIG. 2 "T" section FIG. 3 Top Rail Bottom Rail Your air conditioner is designed to install in standard double hung windows with opening widths of 23 to 36 inches (584 mm to 914 mm) (FIG. 4A ̹ FIG. 4B)̻ Lower sash - Frigidaire FFRE0633Q1 | Installation Instructions - Page 3
How to Install Installation Keep a firm grip on the air conditioner, carefully place the unit into the window opening so the bottom of the air conditioner frame is against the window sill (FIG. 6A & FIG. 6B). Carefully close the window behind the top rail of the unit. FIG. 6A FIG. 6B - Frigidaire FFRE0633Q1 | Installation Instructions - Page 4
power cord. Remove sash seal from between windows, and unscrew sash lock. Remove screws installed through frame and framelock. Close (slide) side panels into frame. Keeping a firm grip on air conditioner, raise sash and carefully remove. Be careful not to spill any condensate water while lifting
-
1 -
2 -
3 -
4
 |
 |
READ BEFORE INSTALLING UNIT
MSII Window Mounting (5,000~8,000 BTU)
1
Installation Instructions
Before installing, the top rail must be assembled on the unit.
Philips
Screwdriver
Drill (If pilot holes are needed)
TOOLS NEEDED
DO NOT USE ANY SCREWS OTHER THAN
THOSE SPECIFIED HERE.
NOTE:
SAVE CARTON and these INSTALLATION
INSTRUCTIONS for future reference. The carton is
the best way to store unit during winter, or when not
in use.
FOR SAFETY REASONS, THE TOP RAIL MUST BE
SECURELY FASTENED WITH ALL FOUR (4)
SCREWS.
A. Remove the air conditioner from the carton and place on a flat surface.
B. Remove top rail from the rear of the packaging material as shown in Fig. A
C. Align the hole in the top rail with those on the top of the unit as shown in Fig. B
7
sash lock
1
Mounting Hardware
Qty.
2
lock frame
(For Vinyl-Clad windows)
2
lock frame
(For Wooden windows)
weather seals
5
window sash seal foam
1
Top Rail Hardware
Qty.
4
1
Top Rail
Some assembly is required. Please read these instructions
carefully.
2020211A2579
Fig. B
Packaging
Fig. A
Fig. C
Top Rail
The unit is for window mounting only.
INSTALLATION WARNINGS AND CAUTION
Pay attention to danger and safety notices.
To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp edges that may
be exposed:
Air conditioners covered in this manual pose an excessive weight hazard. Two or more people are needed to move and install
the unit. Wear protective gloves whenever lifting or carrying the unit. AVOID the sharp metal fins of front and rear coils. To
prevent injury or strain, use proper lifting and carrying techniques when moving unit.
Carefully inspect location where air conditioner will be installed. Be sure it will support the weight of the unit overan extended
period of time.
Handle air conditioner with care.
Make sure air conditioner does not fall during installation.
Carefully read the installation manual before beginning.
Follow each step as shown.
Observe all local, state, and national electrical codes and by qualified, licensed, authorized personnel only.