Frigidaire FFTH1222R2 Installation Instructions
Frigidaire FFTH1222R2 Manual
 |
View all Frigidaire FFTH1222R2 manuals
Add to My Manuals
Save this manual to your list of manuals |
Frigidaire FFTH1222R2 manual content summary:
- Frigidaire FFTH1222R2 | Installation Instructions - Page 1
Installation Instructions READ BEFORE INSTALLING UNIT For Through-the-Wall Air Conditioners INSTALLATION WARNINGS AND CAUTION Carefully read the installation manual before beginning. Follow each step as shown. Observe all local, state, and national electrical codes and by qualified, licensed, - Frigidaire FFTH1222R2 | Installation Instructions - Page 2
a stop for the Air Conditioner. For new installations, a Frigidaire Sleeve Kit (EA108T) is recommended. CAUTION: When installation is complete, replacement unit MUST have a rearward slope as shown in Fig.1. 2. Remove old Air Conditioner from wall sleeve and prepare wall sleeve as follows: Clean - Frigidaire FFTH1222R2 | Installation Instructions - Page 3
-Westinghouse/Frigidaire 22Ǝ Deep 5. Identify your wall sleeve type and follow the instructions for that type in the following pages. IMPORTANT This unit's increased performance characteristics result from having two rear air intakes. It is very important that these installation instructions are - Frigidaire FFTH1222R2 | Installation Instructions - Page 4
Installation Instructions Wall Sleeve Brands: #1 Emerson 15" Deep 1. Remove existing rear grille as shown on Page 3 of this manual and replace with provided louvered rear panel. Install as shown here. NOTE: You may need to drill holes in flange of existing sleeve to match new rear grille Rear - Frigidaire FFTH1222R2 | Installation Instructions - Page 5
Installation Instructions Wall Sleeve Brands: #2 Fedders 19-3/4" Deep 1. Remove existing rear grille as shown on Page 3 of this manual and replace with provided louvered rear panel. Install as shown here. NOTE: You may need to drill holes in flange of existing sleeve to match new rear grille - Frigidaire FFTH1222R2 | Installation Instructions - Page 6
Installation Instructions Wall Sleeve Brands: #3 Fedders or Friedrich 16-3/4" Deep 1. Remove existing rear grille as shown on Page 3 of this manual and replace with provided louvered rear panel. Install as shown here. NOTE: You may need to drill holes in flange of existing sleeve to match new - Frigidaire FFTH1222R2 | Installation Instructions - Page 7
Installation Instructions Wall Sleeve Brands: #4 General Electric/Hotpoint 16-7/8" Deep 1. Remove existing rear grille as shown on Page 3 of this manual and replace with provided louvered rear panel. Install as shown here. NOTE: You may need to drill holes in flange of existing sleeve to match - Frigidaire FFTH1222R2 | Installation Instructions - Page 8
Installation Instructions Wall Sleeve Brands: #5 Sears or Carrier 51S Series 18-5/8" Deep 1. Remove existing rear grille as shown on Page 3 of this manual and replace with provided louvered rear panel. Install as shown here. NOTE: You may need to drill holes in flange of existing sleeve to - Frigidaire FFTH1222R2 | Installation Instructions - Page 9
Installation Instructions Wall Sleeve Brands: #6 Whirlpool 17-1/8" Deep 1. Remove existing rear grille as shown on Page 3 of this manual and replace with provided louvered rear panel. Install as shown here. NOTE: You may need to drill holes in flange of existing sleeve to match new rear grille - Frigidaire FFTH1222R2 | Installation Instructions - Page 10
Installation Instructions Wall Sleeve Brands: #7 Whirlpool 23" Deep 1. Remove existing rear grille as shown on Page 3 of this manual and replace with provided louvered rear panel. Install as shown here. NOTE: You may need to drill holes in flange of existing sleeve to match 80º new rear - Frigidaire FFTH1222R2 | Installation Instructions - Page 11
Installation Instructions Wall Sleeve Brands: #8 White Westinghouse/Frigidaire/ Carrier 52F Series 16"+ 17-1/2" Deep 1. Remove existing rear grille as shown on Page 3 of this manual and replace with provided louvered rear panel. Install as shown here. NOTE: You may need to drill holes in flange - Frigidaire FFTH1222R2 | Installation Instructions - Page 12
Installation Instructions Wall Sleeve Brands: #9 White Westinghouse or Frigidaire 22" Deep 1. Remove existing rear grille as shown on Page 3 of this manual and replace with provided louvered rear panel. Install as shown here. NOTE: You may need to drill holes in flange of existing sleeve to - Frigidaire FFTH1222R2 | Installation Instructions - Page 13
Installation Instructions Direct Unit Mounting The previous directions are the preferable of the grille to the unit can be considered. Note: The grille must be installed prior to inserting the unit into the sleeve. $WWDFKWKHVHDOSLHFHV DVVKRZQLQ)LJ 2̻Position the grille over the rear - Frigidaire FFTH1222R2 | Installation Instructions - Page 14
Installation Instructions FINISHING INSTALLATION: 1. Install the 1" x 11 2 " x 84" long stuffer seal between the wall-sleeve and the unit. A flat-bladed screwdriver or putty knife is recommended. 2. Assemble the trim frame by inserting top and bottom pieces into side pieces and
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
 |
 |
READ BEFORE INSTALLING UNIT
For Through-the-Wall Air Conditioners
1
Installation Instructions
NOTE:
DO NOT USE ANY SCREWS OTHER THAN THOSE SPECIFIED HERE
Note that the air conditioner dimensions are: 24" wide,14" high, and 19" deep (without front). Install Air Conditioner
according to these installation instructions to achieve the best performance. Save these installation instructions for
future reference.
Do This First (for existing sleeve)
You may not need all parts in the kit. Discard unused parts.
Items in Kit
2020213A1639
Hardware
2
2
3
Tapered Spacer Blocks (17” Long)
Plastic Divider (
)
4
Stuffer Seal (
)
4
1
2
3
4
5
seal
(
)
1
6
2
7
3
8
No.
Qty.
2
9
Centering/Support Blocks (
”
)
4
”
x 3
”
x 1
1
2
1
2
1
2
”
x 4
”
x 14
”
1
8
1
2
1
2
1
”
x 1
”
x 84
”
1
2
1
”
x 1
”
x 25
”
1
2
seal
(
)
1
”
x 1
”
x 14
”
1
2
seal
(
)
1
”
x
3/8
”
x 25
”
seal
(
)
1
”
x
3/8
”
x 14
”
seal
(
)
1
”
x
3/4
”
x 14
”
2
Hardware
2
1
1
Ground Wire (green)
2
13
10
11
12
14
Grounding Screw
15
1
16
1
17
No.
Qty.
4
18
Trim Frame (top & bottom legs)
Grille (plastic)
Grille Aluminum
Nuts (plastic)
Screw w/washer
4
Trim Frame (side legs)
Toothed washer for grounding screw
2
Pay attention to danger and safety notices.
To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp edges that may
be exposed:
Air conditioners covered in this manual pose an excessive weight hazard. Two or more people are needed to move and install
the unit. Wear protective gloves whenever lifting or carrying the unit. AVOID the sharp metal fins of front and rear coils. To
prevent injury or strain, use proper lifting and carrying techniques when moving unit.
Carefully inspect location where air conditioner will be installed. Be sure it will support the weight of the unit overan extended
period of time.
Handle air conditioner with care.
Make sure air conditioner does not fall during installation.
Carefully read the installation manual before beginning.
Follow each step as shown.
Observe all local, state, and national electrical codes and by qualified, licensed, authorized personnel only.
INSTALLATION WARNINGS AND CAUTION