Frigidaire FRA123KT1 Installation Instructions (All Languages)
Frigidaire FRA123KT1 Manual
 |
UPC - 012505274237
View all Frigidaire FRA123KT1 manuals
Add to My Manuals
Save this manual to your list of manuals |
Frigidaire FRA123KT1 manual content summary:
- Frigidaire FRA123KT1 | Installation Instructions (All Languages) - Page 1
Installation Instructions READ BEFORE INSTALLING UNIT For Slider Casement Air Conditioners To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp edges that may be exposed: Air conditioners covered in this manual pose an excessive weight - Frigidaire FRA123KT1 | Installation Instructions (All Languages) - Page 2
use proper lifting techniques. Inspect the condition of the window where unit will be installed. Be sure it will support the weight of the unit. This appliance must be installed according to all applicable codes and ordinances. Handle air conditioner with care. AVOID sharp metal fins on front and - Frigidaire FRA123KT1 | Installation Instructions (All Languages) - Page 3
Installation Instructions 1 Make sure you have all the necessary parts. Installation kit contents (FIG.3): No. Hardware Qty. No. Hardware FIG.3 3 1 Qty. 1 Platform 1 10 6FUHZ IODWKHDG 2 2 2 Support brace 3 Adjustment bolt 4 Hex flange nut - 1/4 5 Track seal 6 Side channel seal 1 11 - Frigidaire FRA123KT1 | Installation Instructions (All Languages) - Page 4
Installation Instructions 3 Choose the proper window location. Choose a window that allows the cooled air to flow freely and directly into room(s) you wish to cool. Remember, it is difficult to move air around corners. Also, choose a window and support brace. Try assembly in the window to determine - Frigidaire FRA123KT1 | Installation Instructions (All Languages) - Page 5
Installation). 10 Adjust platform assemblyVRWKDWRXWVLGHHGJHLVƎORZHUWKDQ inside edge, as shown (FIG.11). This ensures proper water drainage from the air conditioner. 11 Level platform assembly from side-to-side. Also, make sure window of the AC cabinet. Make sure plastic window panel is - Frigidaire FRA123KT1 | Installation Instructions (All Languages) - Page 6
$GGRUJDJHDQJOH Installing the Unit in a Casement Window NOTE: 3ODWIRUP$VVHPEO\ ),* window clearance problems, the unit can be installed in a stationary sash section. However, the horizontal mullion and WKHJODVVSDQHOVPXVWEHUHPRYHGEHIRUHLQVWDOODWLRQ 24 Attach support - Frigidaire FRA123KT1 | Installation Instructions (All Languages) - Page 7
hole FIG.22 FIG.23 Window jamb FIG.24 28 Adjust the platform assembly VRWKDWWKHUHDURIWKHDLUFRQGLWLRQHUZLOOEHƎORZHUWKDQWKHIURQW7KLV ensures proper water drainage from the air conditioner. NOTE: A projection below the base of the air conditioner will require the rear of - Frigidaire FRA123KT1 | Installation Instructions (All Languages) - Page 8
Installation Instructions 34 Cut side channel seal into 2 equal lengths. Remove the NOTE: DO NOT push or pull air direction louvers. 36 Place the air conditioner in the window opening as shown (FIG.31). It should sit on the platform assembly so that the window panel frame and the cabinet side
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
 |
 |
READ BEFORE INSTALLING UNIT
For Slider Casement Air Conditioners
1
Installation Instructions
To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp
edges that may be exposed:
Air conditioners covered in this manual pose an excessive weight hazard. Two or more people are needed to
move and install the unit. To prevent injury or strain, use proper lifting and carrying techniques when moving unit.
Carefully inspect location where air conditioner will be installed. Be sure it will support the weight of the unit over
an extended period of time.
Handle air conditioner with care. Wear protective gloves whenever lifting or carrying the unit. AVOID the sharp
metal fins of front and rear coils.
Make sure air conditioner does not fall during installation.
NOTE:
These instructions describe installation in a typical wood framed window with a wood SLIDE-BY sash, or
installation in a metal CASEMENT window. Modification may be necessary when installing in windows made
differently than those shown in these instructions.
WARNING:
Electrical ground is required on this appliance.
DO NOT ground to a gas line.
If cold water pipe is interrupted by plastic, non-metallic gaskets, or other insulating materials, DO NOT use for
grounding.
Check with a qualified electrician if you are in doubt as to whether the appliance is properly grounded.
DO NOT modify power supply cord plug. If it does not fit outlet, have a proper outlet installed by a qualified
electrician.
DO NOT have a fuse in the neutral or grounding circuit. A fuse in the neutral, or grounding circuit could result in
an electrical shock.
DO NOT use an extension cord with this appliance.
Failure to follow these instructions could result in electrical shock, serious injury, or death.
Meeting Electrical Requirements
OBSERVE ALL LOCAL GOVERNING CODES AND ORDINANCES. DO NOT, UNDER ANY CIRCUMSTANCES,
NOTE:
If codes permit, and a separate grounding wire is used, it is recommended that a qualified electrician determine
that the grounding path is adequate and not interrupted by plastic, non-metallic gaskets, or other insulating
materials.