Frigidaire FRS09PYS1 Installation Instructions (All Languages)
Frigidaire FRS09PYS1 Manual
View all Frigidaire FRS09PYS1 manuals
Add to My Manuals
Save this manual to your list of manuals |
Frigidaire FRS09PYS1 manual content summary:
- Frigidaire FRS09PYS1 | Installation Instructions (All Languages) - Page 1
gases or volatile material. 6. Sites with special environmental conditions. 7. Laundry rooms. Indoor Unit 1. The unit must be installed at a site that does not obstruct the flow of air. 2. The site must support the weight of the indoor unit. 3. The site must be easily accessible for maintenance and - Frigidaire FRS09PYS1 | Installation Instructions (All Languages) - Page 2
dry and well ventilated. 2. The site must support the weight of the outdoor unit and allow for vertical installation. 3. There must not be the possibility of site. 4. The unit must be installed at a site where the noise produced by its operation and air discharge does not disturb the neighbors or - Frigidaire FRS09PYS1 | Installation Instructions (All Languages) - Page 3
Parts list NUMBER 1 2 3 4 PART NAME Installation plate Drain Joint Self-tapping scr ew A #7 X 1" Remote controller capacity < 18000 Btu's capacity > 24000 Btu's Liquid side Connecting Ø1/4" 5 pipe Ø3/8" (capacity < 12000 Btu's) assembly Gas side Ø1/2" ( - Frigidaire FRS09PYS1 | Installation Instructions (All Languages) - Page 4
More than 6" Indoor unit More than 6" 1 3 4 8 Air filter More than 1' A 7 6 More than 6" 5 More than 1.65' More than 1.65' 6 B More than 6.6' 2 Attention 1. This illustration is for explanation purposes only. 2. Copper tubes must be insulated independently C Outdoor unit 09 Parts list - Frigidaire FRS09PYS1 | Installation Instructions (All Languages) - Page 5
) Ø 2.56" B 4.21" 4.21" B Indoor unit outline 6" or more from the wall Refrigerant pipe hole (right) Ø 2.56" 6" or more from the ceiling A Installation plate 6" or more from the wall 1.58'' 7.91'' Refrigerant pipe 1.58'' hole (right) Ø 2.56" 5.31'' =18000 Btu's (A:36.97" B:11.73") Indoor - Frigidaire FRS09PYS1 | Installation Instructions (All Languages) - Page 6
, as shown in the figures above. 2. In the case of tiled, concrete or similar walls, create 0.2" diameter holes. Place anchorage supports for the appropriate assembly screws. 3. Fix the installation plate to the wall with eight A type screws. 4. At all times securing to the wall studs is recommended - Frigidaire FRS09PYS1 | Installation Instructions (All Languages) - Page 7
cover from the side panel. The pipe cover must be kept as it may be used when relocating the air conditioner to any other place. 2. For the rear-right-hand and rear-lefthand piping, install the piping as shown in the sideward figure. Bend the connective pipe to be laid at a height of - Frigidaire FRS09PYS1 | Installation Instructions (All Languages) - Page 8
nor intertwist the power wire with any other wiring. 7. Run the drain hose sloped downward to drain out the condensed water smoothly. 13 Indoor unit installation - Frigidaire FRS09PYS1 | Installation Instructions (All Languages) - Page 9
technique requirement in the installation bracket diagram. The installation wall should be solid brick, concrete or the same intensity construction, or action to reinforce, damping supporting should be taken. The connection between bracket and wall, bracket and the air conditioner should be firm - Frigidaire FRS09PYS1 | Installation Instructions (All Languages) - Page 10
[ Aft) 1' Air outlet B( ft) ' Condensate drainage of outdoor unit (no for cooling only) The condensate and defrosting water formd during heating in the outdoor unit can be properly discharged by drainage pipe . Installation method:Insert the drain connection - Frigidaire FRS09PYS1 | Installation Instructions (All Languages) - Page 11
Refrigerant piping connection Unit comes with 16.4' tubing bundle. It is not recommended to cut. If too long, loop for excess. Note: Keep original bend so not kinking of the tube occurs. Flaring work Main cause for refrigerant leakage is due to defect in the flaring work. Carry out correct flaring - Frigidaire FRS09PYS1 | Installation Instructions (All Languages) - Page 12
a spanner and torque wrench, as shown in the following figure. Caution: Excessive twisting may break the nut, depending on the installation conditions. Indoor unit tubing OUTER DIAMETER (inch) 1/4 3/8 1/2 5/8 Flare nut Pipings TIGHTENING TORQUE (lbf.in) 139 260 434 651 ADDITIONAL TIGHTENING - Frigidaire FRS09PYS1 | Installation Instructions (All Languages) - Page 13
Electrical work Electric safety regulations for the initial Installation 1. If there is serious safety problem about the power supply, the technicians should refuse to install the air conditioner and explain to the client until the problem is solved. 2. Power voltage should be in the range of 90%~ - Frigidaire FRS09PYS1 | Installation Instructions (All Languages) - Page 14
tapes, so that they will not touch any electrical components. Secure the cable onto the control board with the cord clamp. Electrical box cover Cable Code wire 0.39" 1.57" Terminal block of indoor unit N(1) 2 3 To Outdoor Unit 19 Electrical work - Frigidaire FRS09PYS1 | Installation Instructions (All Languages) - Page 15
of water, form a loop of the connective cable as illustrated in the installation diagram of indoor and outdoor units. 5. Insulate unused cords (conductors) with could not touch any electrical or metal parts. &RYHU 6FUHZ Cable Code wire 0.39" 1.57" Terminal block of outdoor unit N(1) 2 3 L - Frigidaire FRS09PYS1 | Installation Instructions (All Languages) - Page 16
have an individual power circuit specifically for the air conditioner. As for the method of wiring, be guided by the circuit diagram posted on the inside cable thickness is as specified in the power source specification. 7. Always install an earth leakage circuit breaker in a wet or moist area. 8. - Frigidaire FRS09PYS1 | Installation Instructions (All Languages) - Page 17
Air purging with vacuum pump 1. Check that each tube(both liquid and gas side tubes) between the indoor and outdoor units have been properly connected and all wiring for the test run has been completed. Remove the service valve caps from both the gas and the liquid side on the outdoor unit. Note - Frigidaire FRS09PYS1 | Installation Instructions (All Languages) - Page 18
pump For method of using a manifold valve, refer to its operation manual. 1. Completely tighten the flare nuts at connection point A, B, C the flare nut of the Lo valve on the gas pipe side and check if the air is entering (Operation noise of the vacuum pump changes and a compound meter indicates 0 - Frigidaire FRS09PYS1 | Installation Instructions (All Languages) - Page 19
. Make sure the grounding resistance is less than 4 . 3. Electrical leakage check (performing during test running): During test operation after finishing installation, the serviceman can use the electric probe and multimeter to perform the electrical leakage check. Turn off the unit immediately if - Frigidaire FRS09PYS1 | Installation Instructions (All Languages) - Page 20
well. 3. When the ambient temperature is too low(lower than 63oF), the unit cannot be controlled by the remote controller to run in cooling mode, manual operation can be taken. Manual operation is used only when the remote controller is disable or maintenance necessary. Auto/OFF - Frigidaire FRS09PYS1 | Installation Instructions (All Languages) - Page 21
device. 2. Guarantee that the unit is appropriately fastened and complies with all of the aforementioned safety norms. 3. Before operating the air conditioner, ensure that the air filter is installed correctly. 4. If the unit has been out of use for a long period of time, it is recommended that the
8.
The site must allow for the easy
removal of the connector pipe and
drain hose.
9.
The unit must be installed at a site
protected from direct sunlight.
Precautions for Installation
Installation at the following sites may cause problems. If you must inevitably install
2.
Sites with a high concentration of salinity, such as coastal areas.
3.
Sites with sulfuric gas, such as hot water springs.
4.
Sites with high frequency equipment, such as wireless equipment, welding
machines and medical installations.
5.
Sites with flammable gases or volatile material.
6.
Sites with special environmental conditions.
7.
Laundry rooms.
Indoor Unit
1.
The unit must be installed at a site
that does not obstruct the flow of
air.
2.
The site must support the weight of
the indoor unit.
3.
The site must be easily accessible
for maintenance and replacement
of the air filter.
4.
The site must allow for the
necessary space around the indoor
figure.
that the unit be installed at the
flammable gases.
Choosing the installation site
More
More
More
More
Choosing the installation site
the unit at one of these sites, please consult your local distributor beforehand:
1.
Sites with machine oil.
unit, as shown in the sideward
meter) between the unit and radio
5.
There should be at least 3 feet (1
7.
The indoor unit must be at least 8.2
ft(2.5 meters) from the ground.
6.
It must be far from fire, smoke or
center.
or television devices. It is ideal
than 6
"
than
6"
than
8.2'
than
6"
06
Installation warnings:
Installation
1.
Carefully read the installation manual before beginning.
2.
Follow each step as shown.
3.
Observe all local, state, and national electrical codes and by qualified,
licensed, authorized personnel only.
4.
Pay attention to danger and safety notices