Frigidaire GAK085Q7V Installation Instructions

Frigidaire GAK085Q7V - GIBSON 8000BTU 115V 6.7A 10.0E3 SPD 4 WAY AIR DIRECTION8 Manual

Get Frigidaire GAK085Q7V - GIBSON 8000BTU 115V 6.7A 10.0E3 SPD 4 WAY AIR DIRECTION8 PDF manuals and user guides
UPC - 012505272363
View all Frigidaire GAK085Q7V manuals
Add to My Manuals
Save this manual to your list of manuals

Frigidaire GAK085Q7V manual content summary:

  • Frigidaire GAK085Q7V | Installation Instructions - Page 1
    instructions. A high window accessory kit is available for window heights up to 62" (1575mm). Part on this appliance. DO NOT ground to a gas line. If cold water pipe is use an extension cord with this appliance. Failure to follow these instructions could result in electrical shock, serious
  • Frigidaire GAK085Q7V | Installation Instructions - Page 2
    Be sure it will support the weight of the unit. This appliance must be installed according to all applicable codes and ordinances. Handle AC with care. AVOID sharp metal fins on front and rear coils. Make sure your AC does not fall during installation. Do not use water
  • Frigidaire GAK085Q7V | Installation Instructions - Page 3
    1. Make sure you have all the necessary parts. Installation kit contents: 1. Platform (1) 2. Support brace (1) 3. Adjustment bolt (1) 4. Hex flange nut - 1/4" (1) 5. Track seal (1) 6. Side channel seal (1) 7. Foam seal strip/Sash seal 8. Safety bracket (1) 9-11. Screw - #10x2-1/2" flat-head (2), OR
  • Frigidaire GAK085Q7V | Installation Instructions - Page 4
    bolt hole locations that will create a 45 degree angle between platform and support brace. Try assembly in the window to determine if platform will rest properly inside edge of window track. Using the holes in the platform as a guide, mark and drill two 9/64-inch diameter holes. Drill holes in either
  • Frigidaire GAK085Q7V | Installation Instructions - Page 5
    Preparing For Installation). 7. Adjust platform assembly so that outside edge is 3/16-inch lower than inside edge, as shown right. This ensures proper water drainage from the air conditioner. 8. Level platform assembly from side-to-side. Also, make sure window track is level. Use leveling shims as
  • Frigidaire GAK085Q7V | Installation Instructions - Page 6
    10. Clamp plastic window panel between a board and a work table, and cut along cutting line with a fine tooth saw. Remove any burrs with a file. 11. Fasten side channels to the sides of the AC using 3 screws (Item 17) per channel. Start with first screw at top of channel. Make sure hook ends of
  • Frigidaire GAK085Q7V | Installation Instructions - Page 7
    control positioned through the front in the proper location. Gently push the front into position on the cabinet. It should click into place. Then replace the retaining screws that holds the panel in place. Do not push or pull the front panel louvers. Alternate Window Jamb Applications To install in
  • Frigidaire GAK085Q7V | Installation Instructions - Page 8
    as the pivots in the future. To avoid crank handle and window clearance problems, the unit can be installed in a stationary sash section. However, locations that will create a 45 degree angle between the platform and the support brace. Try the assembly in the window to determine if the platform will
  • Frigidaire GAK085Q7V | Installation Instructions - Page 9
    5. Adjust the platform assembly so that the rear of the air conditioner will be 3/16-inch lower than the front. This ensures proper water drainage from the air conditioner. NOTE: A projection below the base of the air conditioner will require the rear of the platform to be 7/16-inch
  • Frigidaire GAK085Q7V | Installation Instructions - Page 10
    twist the side channel seals with the screws. NOTE: Inserting screws will prevent the air conditioner from being pushed into the room. 16. To replace the front First reconnect the coupler plugs, make the exhaust control positioned through the front in the proper location. Gently push the front into
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
Electrical Shock and Personal Injury Hazard
Electrical ground is required on this appliance.
DO NOT ground to a gas line.
If cold water pipe is interrupted by plastic,
non-metallic gaskets, or other insulating
materials, DO NOT use for grounding.
Check with a qualified electrician if you are in
doubt as to whether the appliance is properly
grounded.
DO NOT modify power supply cord plug. If it
does not fit outlet, have a proper outlet
installed
by a qualified electrician.
DO NOT have a fuse in the neutral or
grounding circuit. A fuse in the neutral, or
grounding circuit could result in an elecrtrical
shock.
DO NOT use an extension cord with this
appliance.
Failure to follow these instructions could result in
electrical shock, serious injury, or death.
WARNING
Installation Instructions
For Slider Casement Air Conditioners
NOTE:
These instructions describe installation in a typical wood framed window with a wood SLIDE-BY sash,
or installation in a metal CASEMENT window. Modification may be necessary when installing in windows made
differently than those shown in these instructions.
A high window accessory kit is available for window heights up to 62" (1575mm). Part # EA103W.
Meeting Electrical Requirements
OBSERVE ALL LOCAL GOVERNING CODES
AND ORDINANCES.
DO NOT, UNDER ANY CIRCUMSTANCES,
REMOVE THE POWER SUPPLY CORD
GROUNDING PRONG.
ELECTRICAL REQUIREMENTS
A 115 volt (103.5 minimum, 126.5 maximum), 60
Hertz, AC only, 15 ampere fused electrical supply
is required. A time delay fuse or time delay circuit
breaker is also required. A separate circuit, serving
only this appliance, MUST be provided.
NOTE:
If codes permit, and a separate
grounding wire is used; it is recommended that a
qualified electrician determine that the grounding
path is adequate and not interrupted by plastic,
non-metallic gaskets, or other insulating materials.
RECEPTACLE WIRING
Receptacle wiring should be a minimum of 14
gauge. Use copper wire only. It is your responsibility
to provide proper and adequate receptacle wiring,
installed by a qualified electrician.
P/N 220215A055
SUBJECT
PAGE
Meeting Electrical Requirements
1
Electrical Connection
2
Preparing For Installation
2
Installing Unit in a Sliding Window
4
Alternate Window Jamb Applications
7
Installing Unit in a Casement Window
8
TABLE OF CONTENTS