Frigidaire GLEB27Z7HS Installation Instructions (All Languages)
Frigidaire GLEB27Z7HS - Electric Wall Oven Manual
![]() |
UPC - 057112083896
View all Frigidaire GLEB27Z7HS manuals
Add to My Manuals
Save this manual to your list of manuals |
Frigidaire GLEB27Z7HS manual content summary:
- Frigidaire GLEB27Z7HS | Installation Instructions (All Languages) - Page 1
INSTALLER. IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE. READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. FOR YOUR SAFETY: Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. Your new wall oven has been designed to fit - Frigidaire GLEB27Z7HS | Installation Instructions (All Languages) - Page 2
Note to the Consumer Keep these instructions with your owner's guide for future reference. IMPORTANT SAFETY INSTRUCTIONS • Be sure your wall oven is installed and grounded properly by a qualified installer or service technician. • This wall oven must be electrically grounded in accordance with local - Frigidaire GLEB27Z7HS | Installation Instructions (All Languages) - Page 3
ELECTRIC WALL OVEN INSTALLATION INSTRUCTIONS (Side Swing Door Models) Wait at least three (3) hours after receiving this built-in oven before switching the power on to prevent possible damage to the built-in oven control at power on. 3. Adjusting Oven Height Oven height can be adjusted when needed - Frigidaire GLEB27Z7HS | Installation Instructions (All Languages) - Page 4
ELECTRIC WALL OVEN INSTALLATION INSTRUCTIONS the service panel. DO NOT ground to a gas supply pipe. DO NOT connect to electrical power supply until appliance is Do not lift the oven by the door Door Reversal Procedure (see Figure 6) 1. Pull the door open. 2. While supporting the door with one hand - Frigidaire GLEB27Z7HS | Installation Instructions (All Languages) - Page 5
ELECTRIC WALL OVEN INSTALLATION INSTRUCTIONS (Side Swing Door Models) 10. Reassemble the handle and filler plates #2, #3 and #12 on the opposite side of the door. 11. Remove and relocate the filler plates #7 on the opposite side of the oven frame. 12. Remove the latch pin #10 and relocate latch on - Frigidaire GLEB27Z7HS | Installation Instructions (All Languages) - Page 6
ELECTRIC WALL OVEN INSTALLATION INSTRUCTIONS (Side Swing Door Models) 8. Turn the outer door assembly a half turn (180°) and replace the outer door assembly over the lower door assembly. Replace the nylon slide under the handle (thin side facing inward) on the same side of the ball screw. Replace - Frigidaire GLEB27Z7HS | Installation Instructions (All Languages) - Page 7
ELECTRIC WALL OVEN INSTALLATION INSTRUCTIONS (Side Swing Door Models) 5. Cabinet Installation A. Easy Clean Models 1. Remove and lay aside the lower vent trim which is taped to the oven outer side panel. 2. Slide the oven into the opening until the side trims fit flush against the wall of the - Frigidaire GLEB27Z7HS | Installation Instructions (All Languages) - Page 8
DIMENSIONS F. WIDTH G. DEPTH H. HEIGHT 27" (68.6 cm) Wall Oven 24 7/8" (63.2 cm) Min. 25 1/4" (64.1 cm) Max. 23 1/2" (59.7 cm) Min. 28 1/8" (71.4 cm) Min. 28 5/8" (72.7 cm) Max. Figure 12- SELF CLEAN MODELS ONLY TYPICAL UNDER COUNTER INSTALLATION OF AN ELECTRIC BUILT-IN OVEN WITH AN ELECTRIC - Frigidaire GLEB27Z7HS | Installation Instructions (All Languages) - Page 9
ELECTRIC WALL OVEN INSTALLATION INSTRUCTIONS (Side Swing Door Models) 18" (45.7 cm) Max. 5" (12.7 cm) 6 1/2" Max. (16.5 cm) Min. Flare Union Flexible Appliance Conduit Wall Oven Cabinet Cabinet sides or filler panel Flare Union 120V/60Hz Grounded Outlet Pressure Regulator Manual Shutoff Valve - Frigidaire GLEB27Z7HS | Installation Instructions (All Languages) - Page 10
(si los hay) de los muros laterales o/y de la parte posterior del horno emportado. Estos espaciadores centran el horno en el requerida es 10" (25.4 cm) por modelos fácilmente limpiables. 1 1/2" (3.8 cm) Min. 27" Min. (68.6 cm) Ubicación para la caja de empalme eléctrica y el agujero para - Frigidaire GLEB27Z7HS | Installation Instructions (All Languages) - Page 11
para el instalador 1. Lea todas las instrucciones contenidas en este manual antes de instalar el horno. 2. Saque todo el material edición en los Estados Unidos, o el Código Eléctrico Canadiense CSA Standard C22.1, Part 1, en Canadá. Pisar, apoyarse, o sentarse sobre la puerta de este horno a pared - Frigidaire GLEB27Z7HS | Installation Instructions (All Languages) - Page 12
con el Código Eléctrico Nacional ANSI/ NFPA No. 70-última edición en los Estados Unidos, o el Código Eléctrico Canadiense CSA Standard C22.1, Part 1, en Canadá. En este electrodomestico se necesita un cable de toma a tierra. Este electrodomestico viene equipado con un cable de conexión de cobre. Si - Frigidaire GLEB27Z7HS | Installation Instructions (All Languages) - Page 13
para sacar el pasador de bisagra inferior y remueva la puerta. 3. Ponga la puerta sobre una mesa protegida con una manta; la superficie de la parte interior de la puerta debe de ser en frente a usted. 4. Remueva los dos tornillos que aseguran el tirador; remueva el tirador. Remueva las tirantes - Frigidaire GLEB27Z7HS | Installation Instructions (All Languages) - Page 14
. Remueva el pasador de cerrojo # 10 y vuelva a poner el cerrojo al lado opuesto de la puerta del horno. 13. Invierta las ubicaciónes de los partes fijados de los contramarcos # 8 y # 9 (por ejemplo del lado izquierdo de arriba al lado derecho de abajo). 14. Vuelva a poner la puerta en el horno de - Frigidaire GLEB27Z7HS | Installation Instructions (All Languages) - Page 15
la llave de luz del horno en el nuevo hoyo en el marco del horno. 19. Reponga la puerta. Primero ponga el manguito en la parte superior de la puerta por encima del perno de la bisagra inferior (asegúrese que la arandela quede en su lugar). 20. Cuidadosamente cierre la - Frigidaire GLEB27Z7HS | Installation Instructions (All Languages) - Page 16
lateral) 5. Instalación del Gabinete A. Modelos fácilmente limpiables 1. Retire y ponga a un lado la rejilla baja de ventilación que está pegada a la parte exterior del panel lateral del horno. 2. Deslize el horno en la apertura hasta que los contramarcos laterales se ajustan correctamente contra - Frigidaire GLEB27Z7HS | Installation Instructions (All Languages) - Page 17
Si no hay una estufa instalada por encima del horno a pared, se permite un máximo de 5" (12.7 cm). DIMENSIONES DE RECORTADO F. ANCHURA G. PROFUNDIDAD H. ALTURA 27" (68.6 cm) Horno de pared 24 25 7/8" 1/4" (63.2 (64.1 cm) cm) Min. Max. 23 1/2" (59.7 cm) Min. 28 1/8" (71.4 cm) Min. 28 - Frigidaire GLEB27Z7HS | Installation Instructions (All Languages) - Page 18
controles del horno una vez más. Véase el Manual del Usuario o el Guía de controles de horno electrónico para la operación. Siga las instrucciones Un ventilador en la parte superior y atrás, arriba del horno provee un enfriamiento adicional para los componentes eléctricos y electrónicos del horno. - Frigidaire GLEB27Z7HS | Installation Instructions (All Languages) - Page 19
L'INSPECTEUR D'ÉLECTRICITÉ LOCAL. LISEZ ET CONSERVEZ CES INSTRUCTIONS POUR RÉFÉRENCES ULTÉRIEURES. POUR VOTRE SÉCURIT ) (si nécessaire) NOTE: La base doit pouvoir supporter 150 lbs (68 Kg). DIMENSIONS DE L'APPAREIL MODÈLE 27" (68.6 cm) Facile à nettoyer 27" (68.6 cm) Autonettoyant A B 26 7/8 ( - Frigidaire GLEB27Z7HS | Installation Instructions (All Languages) - Page 20
TE-À-CÔTE OU SUPERPOSÉE. Consommateur Conservez ces instructions avec votre guide de l'utilisateur pour références futures. DIRECTIVES établir quelles sont les dimensions applicables à votre modèle, ainsi que l'espace nécessaire pour recevoir l'appareil. La surface qui supporte l'appareil doit être - Frigidaire GLEB27Z7HS | Installation Instructions (All Languages) - Page 21
INSTRUCTIONS D'INSTALLATION POUR FOUR ENCASTRÉ ÉLECTRIQUE (Modèles à porte ouvrant de côté) Il approuvés pour le raccord de fils en cuivre et à des fils en aluminium conformes au National Electrical Code et aux codes et ordonnances locaux. Ces appareils sont fabriqués avec un fil d'alimentation poss - Frigidaire GLEB27Z7HS | Installation Instructions (All Languages) - Page 22
INSTRUCTIONS D'INSTALLATION POUR FOUR ENCASTRÉ ÉLECTRIQUE (Modèles à porte ouvrant de côté) 2. Si l'appareil est utilisé dans une maison mobile, ou si les codes locaux N'AUTORISENT PAS - Frigidaire GLEB27Z7HS | Installation Instructions (All Languages) - Page 23
INSTRUCTIONS D'INSTALLATION POUR FOUR ENCASTRÉ ÉLECTRIQUE (Modèles à porte ouvrant de côté) 9. Réassemblez les moulures #5 et #6 tout en inversant leurs positions (la moulure #5 en bas et la #6 - Frigidaire GLEB27Z7HS | Installation Instructions (All Languages) - Page 24
INSTRUCTIONS D'INSTALLATION POUR FOUR ENCASTRÉ ÉLECTRIQUE (Modèles à porte ouvrant de remontez l'assemblage de charnière à l'extrémité supérieure droite du châssis du four. 13. Démontez le support de porte réglable du côté inférieur droit du châssis du four et placez-le du côté gauche du châssis - Frigidaire GLEB27Z7HS | Installation Instructions (All Languages) - Page 25
INSTRUCTIONS D'INSTALLATION POUR FOUR ENCASTRÉ ÉLECTRIQUE (Modèles à porte ouvrant de côté) 5. Installation dans l'armoire A. Modèles facile à nettoyer 1. Retirez la moulure inférieure qui est attachée - Frigidaire GLEB27Z7HS | Installation Instructions (All Languages) - Page 26
INSTRUCTIONS cm), installé sur deux lisses, de niveau avec le garde pied. Le tout doit pouvoir supporter 150 lbs (68 kg). 4 1/2 po (11.4 cm) Max.* Découpez une ouverture de 5 po (12.7 cm) est permis. DIMENSIONS DE L'OUVERTURE F.LARGEUR G.PROFONDEUR H.HAUTEUR 27" (68.6 cm) Four encastré 24 7/8" - Frigidaire GLEB27Z7HS | Installation Instructions (All Languages) - Page 27
. Référez-vous au Guide de l'utilisateur ou au Guide des controles du four service d'entretien Révisez la liste de vérification préventive et les instructions d'opération dans votre Guide la garantie et aux renseignements sur le service d'entretien dans votre Guide de l'utilisateur. Prière de nous - Frigidaire GLEB27Z7HS | Installation Instructions (All Languages) - Page 28
NOTES - NOTAS 28
![](/manual_guide/products/frigidaire-gleb27z7hs-installation-instructions-languages-5b5b2d5/1.png)
1
ELECTRIC WALL OVEN INSTALLATION INSTRUCTIONS
(Side Swing Door Models)
Door
Open
Spacer
2" (5 cm) Wide Wood
Spacer if Needed
G
F
H
A
D
C
B
27" Min.
(68.6 cm)
2" (5.1 cm)
Min.
28 3/32"
(71.4 cm)
Electrical junction box
and Hole for Cable
space 2" (5.1 cm)
from
right
wall for
Easy Clean Models.
Electrical junction box
(right or left side
depending of model)
31"*
(78.7 cm)
Electrical Junction box
location and Hole for
Cable space 2"(5.1 cm)
from
left
wall for
Self-
Clean Models
.
1 1/2"
(3.8 cm)
Min.
3"(7.6 cm)
Max.
NOTE:
-
Self-clean Models
: Allow at least 27 ¼" (69.2 cm)
clearance for door depth when it is open.
-
Easy-clean Models
: Allow at least 26 ¼" (66.7 cm)
clearance for door depth when it is open.
NOTE:
For a cutout height greater than 29" (73.6 cm) add
one 2" (5 cm) wide wood spacer to each side of the opening
under the appliance side rails.
FOR YOUR SAFETY:
Do not store or use gasoline or other flammable vapors and liquids in
the vicinity of this or any other appliance.
Your new wall oven has been designed to fit a limited variety of cutout sizes to make the job of installing
easier. The first step of your installation should be to measure your current cutout dimensions and
compare them to the cutout dimensions chart below for your model. You may find little or no cabinet
work will be necessary.
INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER.
IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE.
READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
All dimensions are in inches (cm).
P/N 318201508 (0410) Rev. F
English – pages 1-9
Español – páginas 10-18
Français – pages 19-27
Do not remove spacers (if equipped) on the side walls and/or on the back of the built-in oven.
These spacers center the oven in the space provided.
The oven must be centered to prevent excess heat buildup
that may result in heat damage or fire.
Figure 1
* Suggested distance from floor is 31" (78.7 cm)
Minimum required distance is 4 1/2" (11.4 cm)
for
self-clean models
.
Minimum required distance is 10" (25.4 cm)
for
easy-clean models
.
Some models are not available in Canada.
Printed in United States
Figure 2
Do not install the oven
closer than the
dimension
"K"
(see
table) to any adjoining cabinetry or
walls on the door hinge side. This will
interfere with oven rack removal.
Cutout openings
NOTE:
Base must be capable of supporting 150 pounds (68 Kg).
PRODUCT DIMENSIONS
MODEL
A
B
C (wrapper)
D
27" (68.6 cm) Easy Clean
26 7/8 (68.2)
30 9/16 (77.6)
24 11/16 (62.7)
24 1/4 (61.6)
CUTOUT DIMENSIONS
MODEL
Min.
F
Max.
G (Min.)
Min.
H
Max
.
K (Min.)
27" (68.6 cm) Self Clean
27" (68.6 cm) Easy Clean
27" (68.6 cm) Self Clean
26 7/8 (68.2)
31 1/8 (79.1)
24 11/16 (62.7)
25 3/8 (64.5)
24 7/8 (63.2)
24 7/8 (63.2)
25 5/32 (63.9)
25 1/4 (64.1)
23 1/2 (59.7)
23 1/2 (59.7)
28 1/8 (71.4)
28 1/8 (71.4)
29 5/8 (75.2)
30 1/8 (76.5)
3 (7.6)
4 1/2 (11.4)
Figure 2