Fujitsu PDS-5003 User Manual

Fujitsu PDS-5003 Manual

Get Fujitsu PDS-5003 PDF manuals and user guides View all Fujitsu PDS-5003 manuals
Add to My Manuals
Save this manual to your list of manuals

Fujitsu PDS-5003 manual content summary:

  • Fujitsu PDS-5003 | User Manual - Page 1
    USER'S MANUAL 50"/61" WIDE PLASMA DISPLAY PDS5003W/PDS5004W/ PDS5003U/PDS5004U/ PDS6101W Contents Page Before Use • Safety Precautions E-2-E-3 • to this manual whenever questions or problems about operation arise. Be sure to read and observe the safety precautions. Keep this manual where the
  • Fujitsu PDS-5003 | User Manual - Page 2
    , Centennial Avenue Elstree, Hertfordshire, WD6 3SG Manufacturer: Shinjyo Fujitsu General Limited 702-3 Kanazawa Shinjyo-shi Yamagata Japan declares under our sole responsibility that the product, Type: 50" PLASMA DISPLAY Model Name: PDS5003W to which this declaration relates are in conformity
  • Fujitsu PDS-5003 | User Manual - Page 3
    Centennial Park, Centennial Avenue Elstree, Hertfordshire, WD6 3SG Manufacturer: Shinjyo Fujitsu General Limited 702-3 Kanazawa Shinjyo-shi Yamagata Japan declares under our sole responsibility that the product, Type: 50" PLASMA DISPLAY Model Name: PDS5004W to which this declaration relates are
  • Fujitsu PDS-5003 | User Manual - Page 4
    Centennial Park, Centennial Avenue Elstree, Hertfordshire, WD6 3SG Manufacturer: Shinjyo Fujitsu General Limited 702-3 Kanazawa Shinjyo-shi Yamagata Japan declares under our sole responsibility that the product, Type: 61" PLASMA DISPLAY Model Name: PDS6101W to which this declaration relates are
  • Fujitsu PDS-5003 | User Manual - Page 5
    PDS5003W manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. • PDS5004W/PDS5004U (servicing) instructions in
  • Fujitsu PDS-5003 | User Manual - Page 6
    Refer all service to qualified service personnel. - Unplug this product from the wall outlet and refer service to qualified service personnel operate normally by following the operating instructions. Adjust only those controls that are covered by the Operation Manual, as an improper adjustment of
  • Fujitsu PDS-5003 | User Manual - Page 7
    This display uses a plasma display panel and is only 9.8 cm (50") /11.8 cm (61") deep. With its high picture quality and performance, it is perfectly suited for multimedia applications. Variety of input signals • In addition to video, S-video, and RGB, signals, this display supports input of high
  • Fujitsu PDS-5003 | User Manual - Page 8
    Manual (50"U,61"W Type) HANDY TIPS (50"W Type) • Pictures may become "burnt" into the screen phosphors if the screen is left on for extended periods. To ensure that the display has a prolonged service has developed a problem. When this happens in accordance with the instructions given on P. E-42
  • Fujitsu PDS-5003 | User Manual - Page 9
    , wall-mounting unit and other unit when installing this display. Also, be sure that your dealer performs the installation. See the appropriate instruction manual for more information on the installation hardware you select. To ensure proper heat radiation, provide at least as much space around the
  • Fujitsu PDS-5003 | User Manual - Page 10
    to finalize the selection of a desired option in a menu. Warning If the power indicator lamp flashes red, this signifies that the display has developed a problem. When this happens, be sure to remove the power plug from the receptacle and contact your dealer. Leaving the display power ON can result
  • Fujitsu PDS-5003 | User Manual - Page 11
    for 50" type and 4 - 16 Ω for 61" type.) When connecting a cable,attach a ferrite core to the cable. (See P. E-13) *See the speaker instruction manual for more information. 7 Sound 3 input terminal (AUDIO 3 INPUT) Connect this terminal to the sound output terminal of your VCR, etc. (See P.E-37
  • Fujitsu PDS-5003 | User Manual - Page 12
    English 9 Sound 1 input terminal (AUDIO 1 INPUT) Connect this terminal to the sound output terminal of your VCR, etc. (See P.E-37 for the selection of audio input for video input.) 0 RGB 3 synchronization switch (SYNC SW TTL/ANALOG (75 Ω)) This switch is used to terminate horizontal (H) terminal
  • Fujitsu PDS-5003 | User Manual - Page 13
    PART NAMES AND FUNCTIONS (Continued) Description of Input Terminals DVI-D terminal (RGB 1 INPUT/DVI-D) RGB2 input terminal (RGB2 INPUT/mD-sub) Pin No. Input signal Pin No. Input signal 1 Red 9 - 2 Green 10 Ground 3 Blue 11 - 4 - 12 - 5 Ground 13 Horizontal synchronization 6
  • Fujitsu PDS-5003 | User Manual - Page 14
    English Remote Control 1 3 8 1 Power ON button [POWER ON] ➝ (See P. E-16.) 2 2 Power OFF button [POWER OFF] 5 3 RGB input mode selector button [RGB] 4 4 Video input mode selector button [VIDEO] ➝ (See P. E-16.) ➝ (See P. E-17.) ➝ (See P. E-17.) 6 5 Wide screen selector button [WIDE] ➝ (See P.
  • Fujitsu PDS-5003 | User Manual - Page 15
    ° 30° Right 5 m (Front) Upper 20° 20° Lower Information The remote control may not function properly if you use a high-frequency fluorescent lamp. If you experience problems, move the lamp or use the remote control from a different position. E-12
  • Fujitsu PDS-5003 | User Manual - Page 16
    EQUIPMENT Carefully check the terminals for position and type before making any connections. Loose connectors can result in picture or color problems. Make sure that all connectors are securely inserted into their terminals. Terminal VIDEO INPUT S-VIDEO INPUT COMPONENT VIDEO INPUT RGB INPUT
  • Fujitsu PDS-5003 | User Manual - Page 17
    CONNECTING THE DISPLAY TO EXTERNAL EQUIPMENT(Continued) (50") VIDEO INPUT S-VIDEO RS-232C INPUT RGB1 INPUT (DVI-D) RGB2 INPUT (mD-sub) COMPONENT VIDEO INPUT (color difference input) / RGB3 INPUT AUDIO1 AUDIO2 AUDIO3 EXT POWER INPUT INPUT INPUT SP INPUT To video To S-video To RS-232C To display
  • Fujitsu PDS-5003 | User Manual - Page 18
    (61") English POWER INPUT COMPONENT VIDEO INPUT (color difference input) / RGB3 INPUT RGB2 INPUT (mD-sub) RGB1 INPUT (DVI-D) VIDEO INPUT RS-232C S-VIDEO INPUT AUDIO1 AUDIO2 AUDIO3 EXT INPUT INPUT INPUT SP To receptacle To color difference output terminal / To display (analog RGB) output
  • Fujitsu PDS-5003 | User Manual - Page 19
    BASIC OPERATIONS TURNING ON THE POWER 1 Select the OFF/STD-BY switch at the STD-BY of the display. When you do so, the power indicator lamp turns red. (This applies only to 50"display.) * You can also use the switches on the display's control panel to accomplish these steps. 2 Press control. on
  • Fujitsu PDS-5003 | User Manual - Page 20
    English SELECTING INPUT MODE VIDEO INPUT MODE 1 Press mode. to select a desired input Each time you press , a different input mode appears. The sequence is as follows: * You can also use the switches on the display's control panel to accomplish these steps. Video: Displays pictures from
  • Fujitsu PDS-5003 | User Manual - Page 21
    WATCHING PICTURES ON THE WIDE SCREEN SWITCHING BETWEEN SCREEN SIZES 1 Press . The currently selected mode will appear. 2 Press to select a desired picture mode. Each time you press , a different picture mode appears. The sequences used are as follows: Normal mode When you are in a Video or
  • Fujitsu PDS-5003 | User Manual - Page 22
    English SCREEN SIZE Normal Displays pictures of normal size (i.e., a 4:3 aspect ratio). Auto The screen size changes automatically in accordance with the contents of image software you use. Wide1 Displays natural-looking pictures of standard size on the wide screen. Picture of standard size
  • Fujitsu PDS-5003 | User Manual - Page 23
    HOW TO USE MENUS SELECTING OPTIONS IN A MENU Use the [MODE] button on the display or and on the remote control to select a desired input mode. 1 Press . The main menu screen will appear. 2 Press or to switch between sub-menus. Each time you press or , one of the available menus appears. The
  • Fujitsu PDS-5003 | User Manual - Page 24
    English Option (1) Contrast (2) Brightness (3) Color (4) Tint Function Adjusts picture contrast. Adjusts screen brightness. Adjusts color darkness. Adjusts tint. Operation : Higher contrast : Lower contrast : Brighter screen : Darker screen : Darker colors : Lighter colors : More greenish tint :
  • Fujitsu PDS-5003 | User Manual - Page 25
    HOW TO USE MENUS (Continued) USING THE AUDIO MENU When you finish selecting a desired option in the AUDIO menu screen, press . When you do so, the adjustment screen for that option appears. Press or to select option and press or to make adjustment. Press to store. (See P. E-30-E-31.) The
  • Fujitsu PDS-5003 | User Manual - Page 26
    for eliminating flicker. Use or for switching. Select Execute and use or to select an option. Range/Setting -60 to +60 Auto/Manual (Can adjust 1 to 32 for Manual) -1 to +1 -8 to +8 Execute Yes/No Function Menu(See P. E-32, E-34.) Option (1) 24 Frame Mode (for Video, S-video, Comp.video) (2) 3D
  • Fujitsu PDS-5003 | User Manual - Page 27
    HOW TO USE MENUS (Continued) Input Terminal Menu(See P. E-32, E-35-E-36.) Option (1) Video Input (for Video) (2) S-video Input (for S-video) (3) BNC Input (4) D-SUB Input Function Selects video mode. Selects video mode. Selects BNC Input signal. Selects D-SUB Input signal. Operation Use or for
  • Fujitsu PDS-5003 | User Manual - Page 28
    option. Use or for switching. Use or for switching. Use or for switching. Display Code Setting screen and press or to select an option. Select Manual to set up Parameter. Use or for switching. Range/Setting Mode/Time Off (disabled) Time (every 1 hr) Mode (every time mode is switched) Moving area
  • Fujitsu PDS-5003 | User Manual - Page 29
    ADJUSTING PICTURES (PICTURE MENU) BASIC OPERATIONS [EX.: ADJUSTING TINT (Tint)] You can make changes to all picture adjustment options in the PICTURE Menu. The changes you make will be stored for a selected input mode. Therefore, you need to select a desired input mode before making any changes.
  • Fujitsu PDS-5003 | User Manual - Page 30
    English • Adjusting Contrast (Contrast) Any value between -30 and +30 can be selected. : Higher contrast : Lower contrast Press to store. • Adjusting Screen Brightness (Brightness) Any value between -60 and +60 can be selected. : Brighter screen : Darker screen Press to store. • Adjusting
  • Fujitsu PDS-5003 | User Manual - Page 31
    ADJUSTING SCREEN POSITION AND SIZE (POSITION/SIZE MENU) BASIC OPERATION [EX.: ADJUSTING HORIZONTAL DIRECTION OF SCREEN POSITION] You can make changes to all screen adjustment options in the POSITION/SIZE Menu. The changes you make will be stored for the selected input mode. Therefore, you need to
  • Fujitsu PDS-5003 | User Manual - Page 32
    English Adjusting Screen Position (Position) Horizontal position (Horizontal) : Moves screen to the right. → : Moves screen to the left. → Vertical position (Vertical) : Moves screen up. → : Moves screen down. → Press to store. Adjusting Screen Size (Size) Screen width (Width) : Increases
  • Fujitsu PDS-5003 | User Manual - Page 33
    ADJUSTING AUDIO (AUDIO MENU) BASIC OPERATION [EX.: ADJUSTING VOLUME BALANCE (Balance)] You can make changes to all sound adjustment options in the AUDIO Menu. The changes you make will be stored for the selected input mode. Therefore, you need to select a desired input mode before making any
  • Fujitsu PDS-5003 | User Manual - Page 34
    English Adjusting Treble (Treble) Any value between -6 and +6 can be selected. : Stronger treble : Weaker treble Each audio input Adjusting Bass (Bass) Any value between -6 and +6 can be selected. : Stronger bass : Weaker bass Each audio input "Treble" selected in the AUDIO Menu screen
  • Fujitsu PDS-5003 | User Manual - Page 35
    OTHER ADJUSTMENTS (FEATURES MENU) BASIC OPERATION [EX. : SELECTING LANGUAGE (Language)] You can make the following changes in the FEATURES Menu. 1 Press . The main menu screen will appear. 2 Press or to select "FEATURES". Each time you press or , one of the available menus appears in the
  • Fujitsu PDS-5003 | User Manual - Page 36
    Yes or No. Yes: Stores the data of Auto Calibration. No: Disables the execution result of Auto Calibration. (3) Press to execute. When selecting Manual by Clock Phase "Auto Calibration" setting screen "Yes/No" screen to select * On-screen information disappears if you do not take any action
  • Fujitsu PDS-5003 | User Manual - Page 37
    OTHER ADJUSTMENTS (FEATURES MENU)(Continued) FUNCTION • Displaying the optimum movie pictures (24 Frame Mode) Can make the optimum display of 24 frames/second signals such as movie pictures. Each time you press or , one of the available choices appears in the following sequence: On Off On :
  • Fujitsu PDS-5003 | User Manual - Page 38
    English INPUT TERMINAL • Selecting Video Mode (Video Input) You can use this option to select the desired video mode of pictures it will receive to the Video Input terminal. Each time you press or , one of the available modes appears in the following sequence: Auto: Automatically selects NTSC,
  • Fujitsu PDS-5003 | User Manual - Page 39
    OTHER ADJUSTMENTS (FEATURES MENU)(Continued) INPUT TERMINAL • Selecting D-SUB Input (D-SUB Input) All modes You can use this option to select the signal system it will receive to D-SUB Input terminal. (1) Select D-SUB Input and press . D-SUB Input screen appears. (2) Select the signal system
  • Fujitsu PDS-5003 | User Manual - Page 40
    English • Selecting time before DPMS starts (DPMS) All modes You can use this option to select the amount of time before the DPMS function starts. DPMS (which stands for "display power management signaling") allows the display to maintain an automatic power saving function. This function causes
  • Fujitsu PDS-5003 | User Manual - Page 41
    OTHER ADJUSTMENTS (FEATURES MENU)(Continued) • Minimizing phosphor burn-in (Screen Orbiter) You can use this option to move the screen position to minimize phosphor-induced "burn-in". Follow the steps below. (1) Select "Screen Orbiter" and press . The "Screen Orbiter" setting screen will
  • Fujitsu PDS-5003 | User Manual - Page 42
    signal by code number. Each time you press or , one of the available choices appears in the following sequence: Auto Manual Auto: Automatically displays the input signal to the optimum. Manual: Selects RGB code number. Press to store. * In Auto mode, the optimum resolution may not be set up
  • Fujitsu PDS-5003 | User Manual - Page 43
    OTHER ADJUSTMENTS (FEATURES MENU)(Continued) • Setting Exhibition Mode (Exhibition Mode) All modes You can use this option to display the enhanced contrast, which is most suitable for the use by unspecified persons. Each time you press or , one of the available choices appears in the following
  • Fujitsu PDS-5003 | User Manual - Page 44
    English INITIALIZATION OF USER ADJUSTMENT VALUE(FACTORY DEFAULT) You can restore the values of the adjustment/setting made in the MENU to factory settings. 1 Press . The main menu screen will appear. * You can also use the switches on the display's control panel to accomplish these steps. 2
  • Fujitsu PDS-5003 | User Manual - Page 45
    that all installation requirements for that option (as given in the relevant instruction manual) are met. * The colors of options do not match the display dealer. CAUTION: This display (PDS5003W/PDS5003U/PDS5004W/PDS5004U/PDS6101W) is for use only with Fujitsu General Limited's option (P-50WB01,
  • Fujitsu PDS-5003 | User Manual - Page 46
    . The fifth input signal will replace the adjustment value of the first input signal. To do this, select a desired signal and follow the instructions in "Adjusting Screen Position and Size" on P. E-28-E-29 to adjust the parameters. When you finish, the settings will be automatically stored. Thus
  • Fujitsu PDS-5003 | User Manual - Page 47
    PDS5003W/PDS5003U/PDS5004W/PDS5004U remote control, 2AA batteries, 1 instruction manual, 1 power cable, 2 big ferrite cores, 2 small ferrite cores • Specifications and external appearance may be change for the sake of improvement. • is a worldwide trademark of Fujitsu
  • Fujitsu PDS-5003 | User Manual - Page 48
    Regulation --- PDS5003W • EMC:FCC Part 15 Class A, ICES-003 Class A • CE Safety: EN60065 EMC: -4-8 1993 EN61000-4-11 1994 • AS Safety: IEC60950 A1/A2/A3/A4 EMC: AS/NZS 3548 Regulation --- PDS5003U/PDS5004U • UL, CSA Safety: UL6500,C-UL EMC:FCC Part 15 Class A, ICES-003 Class A (PDS5003U) EMC:FCC
  • Fujitsu PDS-5003 | User Manual - Page 49
    of the main unit causing machine failure or fire hazard. HANDY TIPS In the event of problems with the display, check the following explanations before contacting your dealer for servicing. Problem • Power does not turn ON. • No pictures are displayed. • Remote control does not function properly
  • Fujitsu PDS-5003 | User Manual - Page 50
    1116, Suenaga, Takatsu-ku, Kawasaki 213-8502, Japan Printed in Japan 8113153019
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
Before using the display, read this manual carefully so that you know how to use the display correctly.
Refer to this manual whenever questions or problems about operation arise.
Be sure to read and observe the
safety precautions.
Keep this manual where the user can see it easily.
* Installation and removal require special expertise.
Consult your product dealer for details.
Contents
USER’S MANUAL
50”/61” WIDE PLASMA DISPLAY
PDS5003W/PDS5004W/
PDS5003U/PDS5004U/
PDS6101W
Before Use
•
Safety Precautions ··································· E-2–E-3
• Features ····························································E-4
• Accessories ······················································ E-5
•
Handy Tips
······················································· E-5
• Installation ······················································· E-6
Usage
•
Part Names and Functions ·····················E-7–E-11
•
Using the Remote Control ·····························E-12
•
Connecting the Display to External
Equipment ············································ E-13–E-15
•
Basic Operations ············································ E-16
•
Selecting Input Mode·····································E-17
•
Watching Pictures on the Wide Screen ···
E-18–E-19
•
How to Use Menus ······························· E-20–E-25
Adjustments
•
Adjusting Pictures (PICTURE Menu) ··· E-26–E-27
•
Adjusting Screen Position and Size
(POSITION/SIZE Menu) ························ E-28–E-29
•
Adjusting Audio (AUDIO Menu) ·········· E-30–E-31
•
Other Adjustments (FEATURES Menu) ···
E-32–E-40
•
Initialization of user adjustment value
(FACTORY DEFAULT) ·····································E-41
Others
• Options ····························································E-42
•
Factory Settings ············································· E-43
• Specification ···················································E-44
•
Cleaning and Maintenance····························E-46
Page
Page