Fujitsu XG2000 Hardware Guide

Fujitsu XG2000 - Switch Manual

Get Fujitsu XG2000 - Switch PDF manuals and user guides View all Fujitsu XG2000 manuals
Add to My Manuals
Save this manual to your list of manuals

Fujitsu XG2000 manual content summary:

  • Fujitsu XG2000 | Hardware Guide - Page 1
  • Fujitsu XG2000 | Hardware Guide - Page 2
  • Fujitsu XG2000 | Hardware Guide - Page 3
    port 10 Gigabit Ethernet layer 2 switch that achieves unsurpassed standards of high throughput and low-latency performance. This manual explains the procedures required to install your XG2000 and should be read and understood before you start using your XG2000. First edition (February 2007) Second
  • Fujitsu XG2000 | Hardware Guide - Page 4
    and others, and to prevent property damage. When using the XG2000, follow the instructions given in this manual. Warning notations Warnings are included throughout this manual in order to prevent injury to the user and/or material damage. These are two levels of warnings, both of which are composed
  • Fujitsu XG2000 | Hardware Guide - Page 5
    and fire. For XG2000 models with cooling vents, do not block off the vents as these prevent the internal parts of the XG2000 from reaching high temperature power is disconnected, contact the vendor's service department immediately. Continued use of the XG2000 may cause an electric shock and fire.
  • Fujitsu XG2000 | Hardware Guide - Page 6
    as well as damage to the XG2000 and/or to other users and their property, if the XG2000 is not used properly. Category Danger may damage the XG2000.(P.26) Ensure that the rack is sufficiently ventilated and that excess heat is properly exhausted.(P.26) Check that the configuration of devices in
  • Fujitsu XG2000 | Hardware Guide - Page 7
    of this hardware guide, the XG2000, its firmware, and the management software are the responsibility of the user. • Fujitsu and its partners accept security A default login password is set before the XG2000 is shipped. For security reasons, a new password should be chosen before the XG2000 is used
  • Fujitsu XG2000 | Hardware Guide - Page 8
    user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part generates uses, and can radiate radio frequency energy and. If not installed and used in accordance with the instruction manual the XG2000
  • Fujitsu XG2000 | Hardware Guide - Page 9
    life support system, and missile launch control in weapon systems. Do not use the XG2000 for High Safety Required Use without otherwise ensuring the safety level required. Fujitsu and its related companies assume no liability whatsoever for damages arising from use of the XG2000 by the user in
  • Fujitsu XG2000 | Hardware Guide - Page 10
    hardware of the XG2000. • XG2000 User's Guide This manual describes a variety of operations and procedures, including the installation and maintenance of the XG2000. When referring to the "XG2000 User's Guide", the manual name is usually abbreviated as "User's Guide". The user's guide is an online
  • Fujitsu XG2000 | Hardware Guide - Page 11
    something that CAUTION could damage your equipment or result in loss of data". Trademarks and abbreviations used in this manual Company names and products names referred in this manual are registered trademarks or trademarks of respective companies. The trademark ™ and ® have been omitted from this
  • Fujitsu XG2000 | Hardware Guide - Page 12
    10 About This Manual
  • Fujitsu XG2000 | Hardware Guide - Page 13
    Targeted reader and expected knowledge 8 A Organization ...8 Related manuals 8 Symbols used in this manual 9 Trademarks and abbreviations used in this manual 9 Chapter 1 Installation 13 1-1 Parts List ...14 1-2 XG2000 Components 16 1-3 Labels ...19 Chapter 2 Installation and Operation
  • Fujitsu XG2000 | Hardware Guide - Page 14
    Chapter 3 Troubleshooting 37 3-1 Start-up Problems 38 3-2 Hardware Problems 39 Appendix 41 Appendix-A Specifications 42 A.1 Product Specifications 42 A.2 Installation Specifications 42 Appendix-B China RoHS Declaration for the XG2000 43 Appendix-C EC Declaration for the XG2000 44 12
  • Fujitsu XG2000 | Hardware Guide - Page 15
    Installation This chapter lists the items that should be in the XG2000 package, describes the names and functions of the various components of the XG2000. 1 1-1 Parts List 14 1-2 XG2000 Components 16 1-3 Labels ...19
  • Fujitsu XG2000 | Hardware Guide - Page 16
    check that all of the following parts were included in your XG2000 package. Contact the vendor's service department if any parts are missing and/or the manual has any missing or wrongly collated pages. Keep the hardware guide (this manual) and the CD-ROM in a safe place. XG2000 CD-ROM Power code
  • Fujitsu XG2000 | Hardware Guide - Page 17
    (large). • Rack Screws (Small) Flat-head screws for fixing the rack mounting brackets and rack mounting bracket B to the XG2000, and fixing the rack mounting bracket B to the rails. • Rack Screws (Large) Pan-head screws for fixing the XG2000 and the rails to the rack posts. Parts List 15
  • Fujitsu XG2000 | Hardware Guide - Page 18
    the names and functions of the components at the front of the XG2000. Port 1 - 20 upper stand : odd number lower stand : even number Link/Act LED Mng-LAN Speed LED Mng-LAN Link LED Serial Port Link/Act LED Dump Switch Mng-LAN Status LED (Status) Alarm LED (Alarm) Power LED (Power) • Ports
  • Fujitsu XG2000 | Hardware Guide - Page 19
    . - Rear Fan LED (Green/Orange) Green LED lights when the Rear Fan Units is in nor- mal operation. Orange LED when there is a problem with the Rear Fan Unit. • Power Supply Unit Supplies power to the XG2000 (includes an exhaust fan). - Power Supply LED (Green/Orange) Green LED lights when the
  • Fujitsu XG2000 | Hardware Guide - Page 20
    LED will depend on the state of the system. Note that the XG2000 will shut itself off when the Temperature error is detected. Any problems other than those that occur during start up are recorded in the event log. For details of the event log, refer to the "XG2000 User's Guide". 18 Installation
  • Fujitsu XG2000 | Hardware Guide - Page 21
    product ID label, and MAC label are to be found in various places on the XG2000. 1 MAC Label Product ID Label Product ID Label MAC Label Product Nameplate Top view of XG2000 Product Nameplate Right view of XG2000 Warning sticker Obey the following warning: CSA/CE Label FCC Canada Label FCC Label
  • Fujitsu XG2000 | Hardware Guide - Page 22
    FCC Label This indicates statement of Part 15 of FCC rules. FCC Canada Label This indicates notification of CSA. CSA/CE Label This indicates CE Marking. 20 Installation
  • Fujitsu XG2000 | Hardware Guide - Page 23
    part number, serial number, etc. Model ****** Part Number Serial Number PA P* * * * * * 1 DATE **** ** ** 100-240V 1 50/60Hz *** ***A / INPUT **kg Product ID Label This indicates the model and serial number +13 Location Mng-LAN XG2000 Port 1 Port 2 Port3 Port 4 Port 5 Port 6 Port 7
  • Fujitsu XG2000 | Hardware Guide - Page 24
    Address on the MAC label xx:xx:xx:xx:xx:xx+14 xx:xx:xx:xx:xx:xx+15 xx:xx:xx:xx:xx:xx+16 xx:xx:xx:xx:xx:xx+17 xx:xx:xx:xx:xx:xx+18 xx:xx:xx:xx:xx:xx+19 xx:xx:xx:xx:xx:xx+20 xx:xx:xx:xx:xx:xx+21 (=yy:yy:yy:yy:yy:yy) Location Port 13 Port 14 Port 15 Port 16 Port 17 Port 18 Port 19 Port 20 22
  • Fujitsu XG2000 | Hardware Guide - Page 25
    This chapter explains how the user should proceed from installation to operation of the XG2000. 2 2-1 Installation Overview 24 2-2 Installation Procedure 25 2-2-1 Installation requirements 25 2-2-2 Installing the XG2000 in a rack 26 2-2-3 Uninstalling the XG2000 from a rack 30 2-3 Installation
  • Fujitsu XG2000 | Hardware Guide - Page 26
    Installation Overview This section reviews the flow of work as the user proceeds from installation to operation of the XG2000. Install the XG2000 and the proceed with normal operation as follows: 1 Check the components "1-1 Parts List" 2 Check the set up area and install the XG2000 "For Safe Use of
  • Fujitsu XG2000 | Hardware Guide - Page 27
    requirements Before installing the XG2000, read " For Safe Use of the XG2000 (P.2)" and comply with 19-inch rack, refer to the user guide provided with the rack. [540mm (W) X 850mm (D) 19-inch rack] (Unit: mm) 540 Front Service area (Front) Rack (Top) Service area (Rear) 800 850 800 700
  • Fujitsu XG2000 | Hardware Guide - Page 28
    in a rack, note the following. • Certain types of racks cannot be used. To check whether the XG2000 can be installed in a given rack, contact the vendor's service department. CAUTION • Remember that when an installed unit is operating, the temperature inside the rack will be higher than the external
  • Fujitsu XG2000 | Hardware Guide - Page 29
    2. Fix the nuts and rails to the rack posts. First, choose nuts, cage nuts or rack nuts, by the type of hole dug in the rack post. When the rack has square post holes, cage nuts are used. When round holes, rack nuts are used. [When the rack has square post holes] Rack Post Rack Screws (Large)
  • Fujitsu XG2000 | Hardware Guide - Page 30
    [When the rack has round post holes] Rack Post Rack Screws (Large) Rack Post Rack Nuts Rail L Rail R Rack Screws (Large) Rack Post Rack Nuts Front Rack Nuts Refer to Detail A Rack Post Rack Nuts Clip the rack nuts onto the rack post so that the holes are lined up. Detail A [When the rack
  • Fujitsu XG2000 | Hardware Guide - Page 31
    holes that should line up with matching holes on the sides of the XG2000, as shown in the diagram. Attach each rack mounting bracket using the Rack Screws (Small) Rack Mounting Bracket Rack Screws (Small) 4. Slide the XG2000 into the rack and fasten it in place. Two rack mounting bracket of front
  • Fujitsu XG2000 | Hardware Guide - Page 32
    completes the rack installation procedure. Rack Post Rack Post 2-2-3 Uninstalling the XG2000 from a rack The following explains how to uninstall the XG2000 from a rack. 1. Undo the rack screws that were used to fasten the XG2000 to the rack. Rack Screws (Small) Rack Screws (Large) 2. Slide the
  • Fujitsu XG2000 | Hardware Guide - Page 33
    . 1. Install the XPF module in the XG2000. How to install the XFP module is the following, (1) Insert the XFP module with the cable connector facings outward. In cases installing the XFP module in an odd port number, the slot connector facings down. Otherwise, in cases 2 installing the XFP
  • Fujitsu XG2000 | Hardware Guide - Page 34
    how to uninstall the XFP modules from the XG2000. 1. Uninstall the XPF module from the XG2000. How to uninstall the XFP module is the following, (1) Remove the XFP module from the slot. In cases removing the XFP module from an odd port number, lift off the lever horizontally. Otherwise, in cases
  • Fujitsu XG2000 | Hardware Guide - Page 35
    Connecting the fiber optic cables The cables need to be connected to the XG2000 XFP modules. 1. Connect the fiber optic cables to the XG2000. Connect the fiber optic cables to the XFP modules (Port 1 - clear, clean the connector as a first attempt to resolve the problem. Cable Connection 33
  • Fujitsu XG2000 | Hardware Guide - Page 36
    on, pulling, excessively bending, twisting, or overheating a power cord can damage it, and may cause electric shock or fire. • Do not use the XG2000 with a damaged power cord, a damaged power plug, and/ or a loose socket. Continued use under these conditions may cause a fire. • If the power plug
  • Fujitsu XG2000 | Hardware Guide - Page 37
    guaranteed. 1. Execute the "system shutdown" command. If the firmware has not been updated yet, then execute "system shutdown" from the command line. For details of the system shutdown command, refer to the "Command Reference" section in Refer the "XG2000 User's Guide". 2. Disconnect the power cord
  • Fujitsu XG2000 | Hardware Guide - Page 38
    36 Installation and Operation
  • Fujitsu XG2000 | Hardware Guide - Page 39
    Troubleshooting This chapter describes what you should do when your XG2000 has problems. 3 3-1 Start-up Problems 38 3-2 Hardware Problems 39
  • Fujitsu XG2000 | Hardware Guide - Page 40
    is started up. If the cause of the error cannot be resolved, contact the vendor's service department. The following explains some general errors that can occur. Check if any of these match your problem. The XG2000 does not turn on [Symptom] The power code is inserted to the power outlet, but
  • Fujitsu XG2000 | Hardware Guide - Page 41
    LED lights up in orange, and an error is recorded in the event log. In this case, turn the XG2000 off and contact the vendor's service department. Power supply error When a power supply problem is detected, the Alarm LED lights up in orange, the power supply LED of the power supply unit in
  • Fujitsu XG2000 | Hardware Guide - Page 42
    40 Troubleshooting
  • Fujitsu XG2000 | Hardware Guide - Page 43
    Appendix This appendix explains XG2000 specifications. Appendix-A Specifications 42 A.1 Product Specifications 42 A.2 Installation Specifications 42 Appendix-B China RoHS Declaration for the XG2000 43 Appendix-C EC Declaration for the XG2000 44
  • Fujitsu XG2000 | Hardware Guide - Page 44
    XG2000 on XG2000 off Ambient humidity XG2000 on XG2000 off Temperature gradient XG2000 on XG2000 off Ambient dust Ambient noise Electromagnetic compatibility Service less (Non-condensing) 0.15mg/m3 or less 55dB or less FCC Class A CE Marking 800mm 800mm 1U in a 19-inch rack 42 Appendix
  • Fujitsu XG2000 | Hardware Guide - Page 45
    Appendix-B China RoHS Declaration for the XG2000 This document describes China RoHS Declaration for the XG2000. A WARNING The Chinese description in product does not warrant compliance to any other restriction and requirement enforced by Chinese authority, thus it shall not be
  • Fujitsu XG2000 | Hardware Guide - Page 46
    Declaration for the XG2000 The EC Declaration of Conformity and product technical documentation are kept at the following location. address Phone number Product Type Model Number Fujitsu Services Limited 22 Baker Street London W1U 3BW +44-786-782-3346 10GbE L2 Switch PD-XG2000FB / PD-XG2000NB 44
  • Fujitsu XG2000 | Hardware Guide - Page 47
    XG2000 Hardware Guide P3N1-E112-04EN Date of issue: April 2011 Issuing authority: PFU LIMITED Printed in Japan • Contents of this manual are not to be reproduced without permission from PFU. • The contents of this manual may be updated without notice. • PFU assumes no liability for damages to third
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47