Home » Ganz Security Manuals » Security Cameras » Ganz Security DDK-1500D » Manual Viewer

Ganz Security DDK-1500D Manual

View all Ganz Security DDK-1500D manuals

Add to My Manuals
Save this manual to your list of manuals

Ganz Security DDK-1500D manual content summary:

Ganz Security DDK-1500D | Manual - Page 1
Ganz Security DDK-1500D | Manual - Page 2
Of Contents SAFETY PRECAUTIONS 4 1. PRODUCT FEATURES 5 1.1 PRODUCT INSTRUCTIONS 5 1.2 PRODUCT FEATURES 6 1.3 TECHNICAL SPECIFICATIONS 6 2. Name 14 3.4 UPDATING SYSTEM SOFTWARE 14 3.5 IP CAMERA SD CARD TROUBLESHOOTING 16 4. Network Configuration 17 4.1 CABLE CONNECTIONS 17 4.1.1 Connect
Ganz Security DDK-1500D | Manual - Page 3
5.1 MICROSOFT INTERNET EXPLORER 27 5.1.1 Connecting the IP CAMERA 27 5.1.2 Change Image Setting...29 5.1.3 Change the Network Setting 31 5.1.4 Change the System Setting 41 5.1.5 Change the Application Setting 49 5.1.6 Change the SD card Setting 57 5.1.7 Change the Pan/Tilt setting 58 5.1.8
Ganz Security DDK-1500D | Manual - Page 4
SAFETY PRECAUTIONS All the following safety and operational instructions to prevent harm or injury to the or removing covers may expose you to dangerous voltage or other hazards. Please refer all servicing to your distributor / retailer. z Do not use liquid cleaners or aerosols for cleaning.
Ganz Security DDK-1500D | Manual - Page 5
1. PRODUCT FEATURES 1.1 Product Instructions This user-friendly device combines cutting-edge sophistication with practical reliability and believe this unit is the right answer to all your network surveillance problems. Try it and you'll see. PLEASE NOTE: Audio is not supported on the DDK-1500D 5
Ganz Security DDK-1500D | Manual - Page 6
in web server. ¼ Our comprehensive Plug & Play features- * PnP video codec-installation of automatic video codec or any component. * PnP IP address-supports UPnP protocol. * PnP recording-built-in SD card for recording. ¼ Auto white balance (AWB) & auto tracing white balance for color temperatures
Ganz Security DDK-1500D | Manual - Page 7
‧Exposure times: 1/30-1/27,000s. Sensitivity: ‧Minimum Illumination: 0.5 lux @F1.6, 0 lux IR On Image: ‧Image frame rate: up to 25 frames/second. ‧Supports two compression modes, the Motion-JPEG and the MPEG4. ‧5 levels of compression provided. The file size of an M-JPEG compressed image depends on
Ganz Security DDK-1500D | Manual - Page 8
if exposed to very bright objects. Dimensions and weight are as follows. Dimensions / Weight: ‧ High: 110 (mm) ‧Diagram: 142 (mm) ‧Weight: 1400 g Accessories Included: ‧CD-R x 1 ‧Instruction manual. 8
Ganz Security DDK-1500D | Manual - Page 9
2. Name of parts and functions 2.1 Name of parts and functions * " ) ( # $ % ' & ( & ' A. Inner plate mounting holes B. DC level C. Preset D. PC assembly E. IP module F. USB plug H G. Side conduct entry H. Back conduct entry I. SD card slot J. Adjust the inner cover ADJUSTING THE
Ganz Security DDK-1500D | Manual - Page 10
CAMERA ADJUSTMENT $ " # 1. Horizontal angle adjustment: by turning the platform to adjust the horizontal angle B(90 degrees) and C(180 degrees). 2. Vertical angle adjustment: by turning the platform to adjust the vertical angle A(90 degrees) MOUNTING THE HOUSING 10
Ganz Security DDK-1500D | Manual - Page 11
DELAY TIME SET UP % & - " : 5* . & T F D T F D T F D T F D T F D T F D T F D N JO % & - " : 5* . & N JO N JO N JO N JO N JO N JO N JO N JO ALARMj ALARM IN (INPUT)jThis is an alarm input which can be RESET IN OUT GND ALARM
Ganz Security DDK-1500D | Manual - Page 12
2.2 The USB function By connecting the IPCAM with a PC via the USB connector, the IPCAM can provide two different functions. 1. Insert an SD card: As a card reader. Insert an SD card into the IP CAMERA, then connect to the PC. You might transfer files between the SD card and the PC. Once you've
Ganz Security DDK-1500D | Manual - Page 13
3. INSTALLATION Please follow the instructions and the diagram below to set up the system. NOTE: The IP CA MERA is linked by its Video Out connection via a BNC connector to a
Ganz Security DDK-1500D | Manual - Page 14
"UPDATE PROCESSING" will show up on the screen on a blue background; if not, please check out steps 1 to 6 carefully or else inform your technical support while ignoring the following steps. 8. DO NOT power off the IPCAM while this update process is running until the message "UPDATE OK RESET PLEASE
Ganz Security DDK-1500D | Manual - Page 15
working normally, please go back to step 4; otherwise, please inform your technical support. 5. In step 10, if the SD card is not removed and the damage. 7. If the message "CSUM ERROR" appears in step 8, it implies a problem in the file of UPDATE.BIN. 8. Don't interrupt the process while the unit
Ganz Security DDK-1500D | Manual - Page 16
CAMERA SD card Troubleshooting 1. Check if the SD card position is correct or not. Please refer to the manual for the related "IPCAM" directory and contact your technical support regardless of whether there is data or not. WARNING: 1. Performing this troubleshooting process may need a monitor, a PC
Ganz Security DDK-1500D | Manual - Page 17
4. Network Configuration 4.1 Cable Connections Please follow the instructions below to connect your IP CAMERA to a computer or a network and to choose a proper RJ-45 cable configuration for connections. Physical specifications of the RJ-
Ganz Security DDK-1500D | Manual - Page 18
4.1.2 Connect to a LAN Hub (INTRANET) The RJ-45 PIN configuration for connecting with a LAN Hub is shown below. IPICPACMAEMREARA LAN CAMERA TO PC NETWORK CARD RJ-45 uplink HUB / POE PSE 18
Ganz Security DDK-1500D | Manual - Page 19
IP Address You need to set an IP address for the unit if the LAN unit isn't connected to a DHCP server. Otherwise, please follow the instructions given below: Set the IP, MASK and GATEWAY. The following is a sample setting. IP: 192.168.1.X MASK: 255.255.255.0 GATEWAY: 0.0.0.0 NOTE: When only
Ganz Security DDK-1500D | Manual - Page 20
NOTE: When connecting to a network, each connected IP CAMERA must be assigned a unique IP, which must be in the same class type as your network address. IP addresses are written as four sets of numbers separated by periods; for example, 192.168.1.1 Therefore, if the connected network is identified
Ganz Security DDK-1500D | Manual - Page 21
Click the Configuration tag, and check if the TCP/IP is included among the network components list. If the TCP/IP is included, please process section 4.5. If it is not included, please follow section 4.4 to install the TCP/IP. 21
Ganz Security DDK-1500D | Manual - Page 22
4.4 TCP/IP Installation During the installation, you will be requested to insert the Windows CD-ROM. After installation, the PC may be restarted. 4.5 TCP/IP configuration setting Click Start c Settings c Control Panel c Network. Select TCP/IP, and then click Properties. Before processing the IP
Ganz Security DDK-1500D | Manual - Page 23
c If you are using a DHCP server, please select Obtain an IP address automatically. Any assigned IP address for the connected IP Cameras must be in the same class type as the server. If there is no DHCP server, please select specify an IP address and type in the IP address of your PC. This IP
Ganz Security DDK-1500D | Manual - Page 24
4.6 Connection Testing With the previous settings, follow the instructions below to ensure whether you have established the connection successfully. Click Start c Programs c MS-DOS Prompt Type in ping 192.168.1.168, then enter. (See
Ganz Security DDK-1500D | Manual - Page 25
If you receive a response as in the sample screen below, the connection hasn't been successfully established. Please re-check all the hardware and software installations by repeating steps 1 to 5. If you still can't establish the connection after rechecking, please contact your dealer. type IP
Ganz Security DDK-1500D | Manual - Page 26
5. Operating Instructions for Image Software and Network Two choices of software are available for linking with the IP CAMERA: (1) the Microsoft Internet Explorer; and (2) the IP CAMERA
Ganz Security DDK-1500D | Manual - Page 27
5.1 Microsoft Internet Explorer 5.1.1 Connecting the IP CAMERA 1. Start up the Microsoft Internet Explorer, and then follow the steps below to connect the IP CAMERA. 2. Click the URL block at the top of the window. 3. Enter the URL address of the IP CAMERA into the URL block and press the "Enter"
Ganz Security DDK-1500D | Manual - Page 28
Ganz Security DDK-1500D | Manual - Page 29
5.1.2 Change Image Setting Please follow the steps below to change the image setting through the network if necessary. 1. Click the Image button on the home page to enter the image-setting page. Image setting page of MJPEG mode Image setting page of MPEG4 mode 2. Adjust the image setting
Ganz Security DDK-1500D | Manual - Page 30
6. Click the Home button to return to the home page while the new image setting acts on the images to effect the desired changes instantly. (If the setting has not been changed by the above steps, any (re)entry onto the home page will find images in their earlier or original setting.) Exchange the
Ganz Security DDK-1500D | Manual - Page 31
5.1.3 Change the Network Setting Please follow the steps below to change the network settings through the network if necessary. z Set the network options and IP address. 1. Click the Network button in the home page to enter the Network page. 2. The accessible networks here are the "FTP" (MJPEG mode
Ganz Security DDK-1500D | Manual - Page 32
Description of function keys: IP Address: Enter the 4-byte IP Address in the appropriate blank space (the value in each box may be anywhere between 0 and 255). Every Network camera has to own an IP address to be identified on the network. Netmask: Fill in the 4-byte Subnet Mask in the required blank
Ganz Security DDK-1500D | Manual - Page 33
z Change the Network Setting - FTP (MJPEG mode only). Please follow the steps below to change the FTP setting via the network if necessary to upload recording data live. 1. Click the FTP button at top left to enter the "FTP Server Setting" page. 2. Type in the "FTP Server" address, the "User Name",
Ganz Security DDK-1500D | Manual - Page 34
z Change the Network Setting - SMTP (MJPEG mode only). Please follow the steps below to change the SMTP setting through the network if necessary. 1. Click the SMTP button at upper left above to enter the "SMTP Server Setting" page. 2. Click "My Server Requires Authentication" to checkmark the
Ganz Security DDK-1500D | Manual - Page 35
z Change the Network Setting - SNTP. Please follow the steps below to change the SNTP setting through the network if necessary. 1. Click the SNTP button at upper left above to enter the "SNTP Server Setting" page. 2. Enter the IP Address of the SNTP server, and choose one of the time zones as and
Ganz Security DDK-1500D | Manual - Page 36
z Change the Network Setting - DDNS. The "Network" page has, on its upper left, the "DDNS" icon. Please follow the steps below to change the DDNS setting through the network if necessary. 1. Click the DDNS button at upper left above to enter the "DDNS Setting" page. 2. Click "Enable DDNS Function"
Ganz Security DDK-1500D | Manual - Page 37
Description of function keys: Enable DDNS Function: Checkmark to activate the function. DDNS Type: Click to open the list of three DDNS modes to choose from: "DynDNS", "hn", and "adsldns". Click the "Apply" button and connect this website automatically and enter it. Type in your dynamic IP Address
Ganz Security DDK-1500D | Manual - Page 38
through the network if necessary. 1. Click the PPPoE button at upper left above to enter the "PPPoE Setting" page. 2. Please read the "PPPoE Troubleshooting" document first, then press "Close' button. 3. Click the "PPPoE mode" to activate the function. 4. Type in the PPPoE "Account" and the PPPoE
Ganz Security DDK-1500D | Manual - Page 39
. Description of function keys: Max Expired Age: Enter it in the given space from a range of 10~3600. SSDP Port: SSDP stands for Simple Service Discovery Protocol. SSDP searches for upstream Internet gateways using UDP port 1900. UpnP Port: Type in the UpnP Port in the attached space. Submit: Click
Ganz Security DDK-1500D | Manual - Page 40
z Change the Network Setting -Network Traffic. The "Network" page has, on its upper left, the "Traffic" icon. Please follow the steps below to change the UPnP setting through the network if necessary. 1. Click the Traffic button at upper left above to enter the "Network Traffic" page. 2. Type in the
Ganz Security DDK-1500D | Manual - Page 41
default). 2. Choose one of the three modes shown on the page to set the Date and Time of the system. The three modes are "Set Manually", "Synchronize With Computer Time", and "Synchronize With SNTP Server". 3. Click the Submit button to submit the new Date and Time settings. 4. Click the Home button
Ganz Security DDK-1500D | Manual - Page 42
z Change the System Setting - Timestamp. (For High Resolution CCD Network camera only) Please follow the steps below to change/add the timestamp through the network if necessary. 1. Click the Timestamp button on the left side of the "System - Date and Time" page to enter the "System - Timestamp"
Ganz Security DDK-1500D | Manual - Page 43
z Change the System Setting - Users. Please follow the steps below to change/add the users' authority through the network if necessary. 1. Click the Users button on the left side of the "Date and Time" page to enter the "Users" page. 2. Add, modify or delete any user's data if necessary. 3. Click
Ganz Security DDK-1500D | Manual - Page 44
z Change the System Setting - Digital I/O. Please follow the steps below to change the Digital I/O through the network if necessary. 1. Click the Digital I/O button on the left side of the "Date and Time" page to enter the "Digital I/O Setting" page. 2. Mark the "Digital Input" "ON" or "OFF" and the
Ganz Security DDK-1500D | Manual - Page 45
Ganz Security DDK-1500D | Manual - Page 46
z Change the System Setting - RS485 Setting. Click the RS485 Setting button on the left side of the "Date and Time" page to enter the "RS485 Setting" page. Description of function keys: Baud rate: Eight different speeds can be used: 2400 baud per second, 4800 baud, 9600 baud, 19200 baud, 28800 baud,
Ganz Security DDK-1500D | Manual - Page 47
z Change the System Setting - Update Firmware. Please follow the steps below to change the Audio Mechanism through the network if necessary. 1. Click the Update Firmware button on the left side of the "Date and Time" page to enter the "Update Firmware" page. 2. Click the "Browse..." button to select
Ganz Security DDK-1500D | Manual - Page 48
z View the Event Logs. Please follow the steps below to view events through the network if necessary. 1. Click the Events button on the upper left above to enter the "Event Log" page. 2. Choose one of the three buttons shown on the page to view an event when necessary. The three buttons are titled "
Ganz Security DDK-1500D | Manual - Page 49
5.1.5 Change the Application Setting Please follow the steps below to change the application setting through the network if necessary. z Change the Application Setting - FTP Application Setting (MJPEG mode only). Please follow the steps below to change the FTP setting via the network if necessary to
Ganz Security DDK-1500D | Manual - Page 50
z Change the Application Setting - SD Card Application Setting. Please follow the steps below to change the SD CARD setting via the network if necessary to upload recording data live. 1. Click the SD card button on the top left to enter the "SD Card Application Setting" page. SD Card setting page
Ganz Security DDK-1500D | Manual - Page 51
z Change the Application Setting -SMTP Application Setting (MJPEG mode only). Please follow the steps below to change the SMTP setting via the network if necessary. 1. Click the SMTP button on the left side to enter the "SMTP Application Setting" page. 2. Enter the attached file number as and when
Ganz Security DDK-1500D | Manual - Page 52
z Change the Application Setting -Language Setting. Please follow the steps below to change the Language setting via the network if necessary. 1. Click the Language button on the left side to enter the "Language Setting" page. 2. You have an option as to which language to use. The default is "
Ganz Security DDK-1500D | Manual - Page 53
z Change the Application Setting -Record Application Enable Setting. Please follow the steps below to change the setting via the network if necessary. 1. Click the Enable Record button on the left side of the record to enter the "Record Application Enable Setting" page. Record setting page of MJPEG
Ganz Security DDK-1500D | Manual - Page 54
z Change the Application Setting -Record - Schedule. 1. Click the Application button on the home page to enter the "Schedule" page. 2. Check/uncheck any/all of the first seven boxes set vertically in the upper half of the "Schedule" page to enable/disable the programmed recording function, and vary
Ganz Security DDK-1500D | Manual - Page 55
z Change the Application Setting - Alarm Application Enable Setting. Please follow the steps below to change the setting via the network if necessary. 1. Click the Enable Alarm button on the left side of the record to enter the "Alarm Application Enable Setting" page. MJPEG mode MPEG4 mode 2.
Ganz Security DDK-1500D | Manual - Page 56
z Change the Application Setting -Motion Detection. Please follow the steps below to enable changes in the motion detection function of the alarm through the network if necessary. Set the motion detection: 1. Click the Motion Detection button on the left side of the Alarm to enter the "Motion
Ganz Security DDK-1500D | Manual - Page 57
5.1.6 Change the SD card Setting Please follow the steps below to change the SD card setting through the network if necessary. z Change the SD card Setting - FILELIST of MEMORY CARD. Please follow the steps below to change the setting via the network if necessary. 1. Click the "SD card" button at
Ganz Security DDK-1500D | Manual - Page 58
5.1.7 Change the Pan/Tilt setting *This item is not supporting this function. * Click the Pan/Tilt button on the home page to open the Speed Dome Controller. 1. Click "Configure" to enter to the RS485 setting
Ganz Security DDK-1500D | Manual - Page 59
5.1.8 PPPoE & DDNS Using the PPPoE 1. Install the XDSL software (obtained from your ISP dealer) in your PC. 2. Search your IP CAMERA's IP address: you can use your Network Viewer's Scan IP program, or just connect the IP CAM and the Video monitor. The monitor screen will show the IP address on its
Ganz Security DDK-1500D | Manual - Page 60
Test: Go to the Internet. 1. Set your PC to enter the Internet. 2. Desktop → IE browser → Type in the IP CAMERA IP address (the same address as in the PPPoE settings and step 3 above) → You can see the IP CAM images. DDNS settings 1. Check your IP CAMERA's IP address ( Scan IP software or monitor )
Ganz Security DDK-1500D | Manual - Page 61
5.2 The IP CAMERA IP Surveillance This section provides instructions for installing and using the IP surveillance and Image Viewer, which are included with the IP CAMERA. The programs can be operated by a selected PC
Ganz Security DDK-1500D | Manual - Page 62
CD-R. 1. Exit all applications currently running in the selected PC. 2. Insert the supported CD in the CD-ROM drive. The program will execute the installation automatically. Follow the on-screen instructions to proceed with the rest of the installation procedure as they appear. NOTE: It will
Ganz Security DDK-1500D | Manual - Page 63
correctly. Click the "Cancel" button and exit the login of the Network Viewer. View the Network camera video from a remote PC Follow the instructions below to use the IP surveillance to browse a Network camera video from a remote location. Upon entering the IP surveillance, a connection box will
Ganz Security DDK-1500D | Manual - Page 64
1. Press the button to enter the Settings page. 2. Press the button to add a new device group. After typing in the Group Name, please press the OK button. 3. Add a channel from the button. 4. (1) Click the Auto-Search button at the bottom of the "Connect Network camera Wizard" page to
Ganz Security DDK-1500D | Manual - Page 65
begin viewing images with this camera from the Device List. NOTE: To add more connections or units to the Network camera, please repeat the above instructions. 65
Ganz Security DDK-1500D | Manual - Page 66
5.2.4 Operation 5.2.4.1 Live Monitor Once the connection has been established, click the button to enter the Live Monitor window. (See the sample screen below.) On the left side of the window is the connected device that has been arranged when you established the connection. 1. The Live Monitor
Ganz Security DDK-1500D | Manual - Page 67
multi-screen, and one sequence; the picture will sequentially switch to different channels according to the Sequence Views setting (refer to 5.2.4.3). Note: One can't use the common icon (#11) in the Sequence displaying mode or drag the video and drop it as s/he likes. For the further settings of
Ganz Security DDK-1500D | Manual - Page 68
»Delete a camera video from the Live Monitor area: (1) Select the video of the camera which you want to delete. (2) Press and hold the left mouse button. Then drag it to the trashcan and release the mouse button. 12. Alarm list / PTZ Control: Shows the alarm types, the device names and the
Ganz Security DDK-1500D | Manual - Page 69
5.2.4.2 Playback Viewer Press the button to enter the Playback Viewer setting page. 1. The Playback Viewer icon. 2. The display area. 3. Click to choose the Recording List / . Live Event Message The alarm events which were recorded will be marked in pink color. Click to refresh the recording
Ganz Security DDK-1500D | Manual - Page 70
NOTE: To view the alarm lists of a camera which were recorded, please (1) click the icon (2) the Alarm List window will appear as shown below, (3) select a camera from the drop-down list, then (4) click the "Search" button. 4. Move to the left/right area. 5. Recorded video list box. This box
Ganz Security DDK-1500D | Manual - Page 71
z Play Rate: During play mode, please use the scroll bar to control the show speed. 7. Shows the device title. 8. This allows you to search a recorded video kept in the HDD of the device. Enter the MONTH /DAY /YEAR /HOUR /MINUTE you wish to search and click to proceed. 9. Functions to fit the
Ganz Security DDK-1500D | Manual - Page 72
5.2.4.3 Setting Press the button to enter the Setting page. 1. The Setting page. 2. Function buttons: z Add a new device group: Click this button and type in the new group, then press "OK" to save it. z Remove a device group: Click this button and select the group name, then press "OK" to
Ganz Security DDK-1500D | Manual - Page 73
four pages of settings. (1) Device Setting page (2) Image Setting page NOTE: The IP Surveillance software connects the Internet to a Network camera. There may be a problem if the bandwidth is not enough, in which case the speed rate of the image transmissions may become too low. So if you want
Ganz Security DDK-1500D | Manual - Page 74
(1) Global Settings z Monitor setup: Sets the date/time mode and display mode, and controls the CPU use percentage on five levels. z Default Directory: Sets the default files' saving path. Click to select the directory. (2) Event Notification z Channel Prompt: Sets each camera to activate or
Ganz Security DDK-1500D | Manual - Page 75
z Popup Message: Sets the maximum number of the pop-up messages, the displaying time and the pop-up forms. Tick mark the blank space for each device to activate it. z E-mail Notice: Sets each camera to activate the E-mail Notice function of the three situations: "Motion Alarm", "Sensor Alarm", and "
Ganz Security DDK-1500D | Manual - Page 76
(3) Recording Settings z Recording Settings: You can control the HDD reserved space by using the scroll bar. z Recording quota setting: Set the maximum recording quota of each channel. (4) Scheduler (1) Choose one of the devices to set its recording schedule. (2) Select the period: Click to set to
Ganz Security DDK-1500D | Manual - Page 77
(3) Select the recording time: Sets the periods of time in recording. Select the Begin time and the End time the time markers will display above. Please use the up (increase) and down (decrease) arrows to adjust the setting. Add the selected period schedule. You can also hold down the left mouse
Ganz Security DDK-1500D | Manual - Page 78
The user has to modify the "Sequence Views Setting" to make it work. For example, if you want to see the 4-window sequence, please follow the steps given below: Step 1: Click the Sequence Views button to enter the Sequence Views setting page. Step 2: Select the "4 SEQ views" and the area. 4-
Ganz Security DDK-1500D | Manual - Page 79
(6) Speed Dome z Tick mark to activate the Speed Dome Controller function of the selected channel. The user can set the model, ID and the protocol here. z Click "Configure" to enter to the RS485 setting pages. (7) Authority Setup Authority setup: Change or add the user's authority. There are three
Ganz Security DDK-1500D | Manual - Page 80
5. List of cameras and its groups: The users can use the icons above the list to change the groups' names, the devices' titles and the channels' display modes. 6. Display area: Click the title of the camera, and you will see the live image in this area. 7. Device Recording: Click the "Start Record"
Ganz Security DDK-1500D | Manual - Page 81
5.2.4.4 Lock Press the button to lock the operation of this software, and the IP Surveillance monitor will be minimized into the systray*of the Windows taskbar. To unlock the command, please click the button once, then type in the correct password. *: The Microsoft Windows systray is a portion
Ganz Security DDK-1500D | Manual - Page 82
5.2.4.7 Exit Setting Press the button to exit the IP surveillance monitor which is minimized into the systray of the Windows taskbar. Click the button to select the functions on the list. You can also change the password by clicking the "Tools" and "Change password" items on the list. Enter the
Ganz Security DDK-1500D | Manual - Page 83
with a digital watermark. It's a checking software which protects archived images and informs you whether the images have been modified or not. Follow the instructions below to open an archived image from an SD card or an HDD. This is image integrity-protection software. It not only allows you to
Ganz Security DDK-1500D | Manual - Page 84
6. ADVANCED OPERATION Question 1: How to view the live images of the IPCAM via the Microsoft Internet Explorer on the Desktop PCs or the laptop computers in a situation where there are no monitors or television? »The way to get the IP address of the IPCAM without a monitor: There are three way to
Ganz Security DDK-1500D | Manual - Page 85
NOTE: Please remember to insert the SD card into the built-in SD slot of the unit first. »Set the recording time (the AVI duration) of the SD card 1. Click the application button in the home page into the "SD-Card APPLICATION SETTING" page. 2. Choose the AVI Duration from the drop-down list. If you
Ganz Security DDK-1500D | Manual - Page 86
4. Enter the Account and the Password which are provided from your ISP. 5. Click the Submit button to submit the setting. NOTE: Please refer to section 5.1.8 for more details. »Use the Sub Hostname to view the IPCAM 1. Click the URL block at the top of the PC screen. 2. Type in the DDNS Host Name of
Ganz Security DDK-1500D | Manual - Page 87
2. Click the FTP button on the left side of the page to enter the "FTP APPLICATION SETTING" page. 3. Set the last item "Upload Rate" at the bottom of the page to the rate you want. If you want to record at the rate of 1F/8S, please choose "1F/8S" in the drop-down list. NOTE: The FTP function is not
Ganz Security DDK-1500D | Manual - Page 88
(96 zones, 5 levels) Ethernet (RJ-45 wired, 10/100 base-tx), MDIX support TCP/IP, DHCP, HTTP, ICMP, UPnP, ARP, DNS, DDNS, PPPoE, *FTP, (32ċ~ 122ċ) 110mm(High) X 142 mm (Diagram) FCC, CE, RoHS User manual x 1 IP-SURVEILLANCE software x 1 *Specifications are subject to change without notice. **FTP
Ganz Security DDK-1500D | Manual - Page 89
8. Functions of client PC System requirement Browser Live Monitor Playback Viewer Settings Multi-camera link Windows 2000, XP or above IE 6.x Max. 16 Split , Real Time REC/ Capture/ Audio/ Live Event/ Full Screen Playback, Time / live event Search / Export (JPEG / AVI) Device/ System/ Camera
Ganz Security DDK-1500D | Manual - Page 90
APPENDIX 1. -SCANIP Follow the instructions below to use the SCANIP software to search the IP CAMERA devices from a local location. 1. Click the button to discover the connection of the all-
Ganz Security DDK-1500D | Manual - Page 91
insertion of "Free IP Address". If you have clicked "No", please manually type in insertions as required in the "Free IP Address", "Gateway Address", and "NET Mask". Follow each insertion you make by typing in the "Login
Ganz Security DDK-1500D | Manual - Page 92
3. Select and double click any of the addresses in the "Free IP Address" box on the right to enter it into an IP Address on the left. 4. To change any IP address, type in the new address in the "Free IP Address" box on the right as well as the device "Login Name" and "Password" in their respective
Ganz Security DDK-1500D | Manual - Page 93
have no idea what the IP ® address of this device is. Now IPCAM supports the UPnP (Universal Plug and Play) protocol ® which makes it easier for it; however, it is a pity that Microsoft Windows XP doesn't start this service by default. Therefore, the following procedures will help you to turn it on
Ganz Security DDK-1500D | Manual - Page 94
Step 1: From the Start menu, point to Settings, and then click Control Panel. See Figure 2. Figure 2 Step 2: When Control Panel appears, double-click the Network Connections icon. The Network Connections dialog box appears. See Figure 3. Figure 3 Step 3: Click the Protocols tab in the Network
Ganz Security DDK-1500D | Manual - Page 95
Figure 5 Step 5: In the Internet Protocol(TCP/IP) Properties dialog box, choose Use the following IP Address to indicate that you do not wish to use DHCP, and assign IP Address 192.168.1.200 with Subnet mask 255.255.255.0. Click OK when you finish it. See Figure 6. Step 6: Choose Close to finish
Ganz Security DDK-1500D | Manual - Page 96
Figure7 2. Install UPnP Packets ® As described before, Microsoft Windows XP doesn't start the UPnP service by default; however, we have to install some packets before we initialize it. The following steps will help you to install them. Step1: From the
Ganz Security DDK-1500D | Manual - Page 97
Figure 9 Step 3: Check the Network Services in the Windows Component Wizard dialog box, and then click Details.... See Figure10. Figure 10 Step 4: Check UPnP User Interface, and choose OK. See Figure 11. Figure 11 97
Ganz Security DDK-1500D | Manual - Page 98
one minute the UPnP installation will be done, and choose Finish to close it. See Figure13. Figure 13 3. Turn on Services After installation, we should turn on the relative services to start the UPnP protocol. The following procedures will teach you how to do it. Step 1: From the Start menu, point
Ganz Security DDK-1500D | Manual - Page 99
Figure 14 Step 2: When Control Panel appears, double-click the Administrative Tools icon. The Administrative Tools dialog box appears. See Figure15. Figure15 Step 3: Click the Services icon in the Administrative Tools dialog box. See Figure16. 99
Ganz Security DDK-1500D | Manual - Page 100
Figure16 Step 4: When the Services dialog box shows up, double click the SSDP Discovery Service icon. See Figure17. Figure17 Step 5: Choose Automatic in the Startup type, and click OK to start it. See Figure18. 100
Ganz Security DDK-1500D | Manual - Page 101
Figure18 Step 6: When the Services dialog box appears again, double click the Universal Plug and Play Device Host icon. See Figure19. Figure19 Step 7: Choose Automatic in the Startup type, press the Start button, and click OK to start it. See Figure20. 101
Ganz Security DDK-1500D | Manual - Page 102
Step 8: Restart your system. Figure20 ® 4. Scan IPCAMs through My Network Place After your installation and starting services, the UPnP protocol will take effect. You can scan all ® IPCAMs in My Network Place like Figure21 and Figure22 below. Figure21 102
Ganz Security DDK-1500D | Manual - Page 103
Figure22 Just double click the UPnP MPEG4 IPCAM icon, and the video live stream will pop up ® automatically without assigning any IP address in Microsoft Internet Explorer . 103
Ganz Security DDK-1500D | Manual - Page 104
APPENDIX 3. -The ARP function Setting the IP Address The Ethernet interface on the IPCAM has a default IP address (192.168.1.168) that most likely needs to be changed to make it work on your local network. You need to acquire a unique IP address (ask your network administrator). For the initial
Ganz Security DDK-1500D | Manual - Page 105
ARP and ping from UNIX or GNU/Linux: 1. Start a shell 2. Type the following as super user (root): arp -s [or arp -s < MAC address>] ping Example: arp -s 192.168.1.100 00-0C-0C-00-00-01 ping 192.168.1.100 The device responds to the ping in the
Ganz Security DDK-1500D | Manual - Page 106
a function which is provided by an American company. Please refer to www.dyndns.com. This chapter provides the user with the basic instructions on how to register a free DDNS service. Registering for a DDNS Enter the URL www.dyndns.com. In the upper right-hand corner of the main page, where there is
Ganz Security DDK-1500D | Manual - Page 107
which is below the "My Hosts" item, as shown in Figure 4. Click "Add Host Service", and its 5 service items will appear. The Add Dynamic DNS Host item helps to add a new DDNS as shown in Figure 5. Each member may have only one free
Ganz Security DDK-1500D | Manual - Page 108
Figure 4 Figure 5 108
Ganz Security DDK-1500D | Manual - Page 109
Figure 6 All we have to set in this page is the "Hostname" item. The user can choose a Sub Hostname as s/he likes from the right-hand side of the Hostname's drop-down list. NOTE: You don't have to set the "IP Address" in the same format as the IPCAM's IP Address. It will renew the IP Address
Ganz Security DDK-1500D | Manual - Page 110
APPENDIX 5. -MPEG4 Bit Rate Lookup Table of IP CAMERA 1. When frame rate is higher than 15 frames/second (15 is not including): Highest High Medium Low Lowest FULL D1 3 VGA 2.63 Half D1 1.5 Half VGA 1.31 CIF 0.75 QVGA 0.66 ZOOM * 2 3 ZOOM * 3 3 ZOOM * 4 3 2.5 2 2.25 1.75
Ganz Security DDK-1500D | Manual - Page 111
APPENDIX 6. -FAQ 1. How to disable the DHCP function and use a static IP instead? AjTurn up the "DIP SWITCH" from "3" to "4" and change the relative network settings, the IP Address, Net Mask and Gateway on the image web page. 2. Can the SD card be removed during recording? AjNo, it cannot be

Match case Limit results 1 per page