Garmin Compact Reactor 40 Hydraulic Autopilot with GHC 50 Instrument Pack Inst
Garmin Compact Reactor 40 Hydraulic Autopilot with GHC 50 Instrument Pack Manual
 |
View all Garmin Compact Reactor 40 Hydraulic Autopilot with GHC 50 Instrument Pack manuals
Add to My Manuals
Save this manual to your list of manuals |
Garmin Compact Reactor 40 Hydraulic Autopilot with GHC 50 Instrument Pack manual content summary:
- Garmin Compact Reactor 40 Hydraulic Autopilot with GHC 50 Instrument Pack | Inst - Page 1
applying power to the device, make sure that it has been properly grounded, following the instructions in the guide. NOTICE For the best possible performance, the device must be installed according to these instructions. When drilling or cutting, always check what is on the opposite side of the - Garmin Compact Reactor 40 Hydraulic Autopilot with GHC 50 Instrument Pack | Inst - Page 2
location should be at or below eye level to provide optimal viewing as you operate your vessel. • The mounting surface must be strong enough to support the weight of the device and protect it from excessive vibration or shock. • To avoid interference with a magnetic compass, the device should not be - Garmin Compact Reactor 40 Hydraulic Autopilot with GHC 50 Instrument Pack | Inst - Page 3
10 If using the nut plates, starting in one corner of the template, place a nut plate over the hole drilled in the previous step. The other hole on the nut plate should line up with the inner 4 mm (5/32 in.) hole on the template. 11 If the 4 mm (5/32 in.) hole on the nut plate does not line up with - Garmin Compact Reactor 40 Hydraulic Autopilot with GHC 50 Instrument Pack | Inst - Page 4
NMEA 2000 Products. To download the reference, go to garmin.com/manuals/nmea _2000. You can also connect this device to Garmin® Marine Network using only a NMEA 2000 network connection. See the installation instructions provided in the corepack of your autopilot system for detailed connection - Garmin Compact Reactor 40 Hydraulic Autopilot with GHC 50 Instrument Pack | Inst - Page 5
2000 network on the boat, you can build one using the cables and connectors supplied in the autopilot corepack. See the installation instructions provided in the corepack of your autopilot system for more information. Autopilot ECU or SmartPump (hydraulic, mechanical, and SmartPump models) Engine - Garmin Compact Reactor 40 Hydraulic Autopilot with GHC 50 Instrument Pack | Inst - Page 6
. NMEA 2000® and the NMEA 2000® logo are registered trademarks of the National Marine Electronics Association. Garmin Corporation M/N: E3545 © 2022 Garmin Ltd. or its subsidiaries support.garmin.com
-
1 -
2 -
3 -
4 -
5 -
6
 |
 |
GHC
™
50
INSTALLATION
INSTRUCTIONS
Important Safety Information
WARNING
Failure to follow these warnings, cautions, and notices could result in personal injury, damage to the vessel or
device, or poor product performance.
See the
Important Safety and Product Information
guide in the product box for product warnings and other
important information.
CAUTION
To avoid possible personal injury, always wear safety goggles, ear protection, and a dust mask when drilling,
cutting, or sanding.
To avoid possible personal injury or damage to the device and vessel, disconnect the vessel's power supply
before beginning to install the device.
To avoid possible personal injury or damage to the device or vessel, before applying power to the device, make
sure that it has been properly grounded, following the instructions in the guide.
NOTICE
For the best possible performance, the device must be installed according to these instructions.
When drilling or cutting, always check what is on the opposite side of the surface to avoid damaging the vessel.
Tools Needed
•
Drill and drill bits
◦
Preparing the surface for cutting:
9 mm (
3
/
8
in.) bit
◦
Installs using wood screws:
2.5 mm (
3
/
32
in.) bit
◦
Installs using the nut plate:
3.5 mm (
9
/
64
in.) bit
4 mm (
5
/
32
in.) bit
•
#2 Phillips screwdriver
•
Jigsaw or rotary tool
•
File and sandpaper
•
Marine sealant (recommended)
GUID-9CEF40E7-A1D9-42A3-9EB1-DF9CF3B47115 v3
January 2023