Garmin GPSMAP 4012 Installation Instructions

Garmin GPSMAP 4012 - Marine GPS Receiver Manual

Get Garmin GPSMAP 4012 - Marine GPS Receiver PDF manuals and user guides
UPC - 753759066055
View all Garmin GPSMAP 4012 manuals
Add to My Manuals
Save this manual to your list of manuals

Garmin GPSMAP 4012 manual content summary:

  • Garmin GPSMAP 4012 | Installation Instructions - Page 1
    and to the GPS antenna (pages 9-10). 4. Ensure the chartplotter software is up-to-date (page 20). Although they are not necessary to use the GPSMAP 4000/5000 chartplotter, this manual covers other installation options: • Connecting the chartplotter to other Garmin Marine Network compatible devices
  • Garmin GPSMAP 4012 | Installation Instructions - Page 2
    To install the bail-mount bracket ➊: Note: You cannot bail mount the GPSMAP 5015/5215 chartplotters. Because of the larger size, you must flush mount the GPSMAP 5015/5215 chartplotter. 1. Using the bail mount as a template, mark the location of the four mounting holes. Be sure to leave at least 5 in
  • Garmin GPSMAP 4012 | Installation Instructions - Page 3
    the chartplotter is snug against the mounting surface. Chartplotter Mounting studs ×4 Flat washers ×4 Lock washers ×4 Rubber gasket Mounting surface Hex nuts ×4 Flush Mounting a GPSMAP 4008/4208/4012/4212/5008/5208/5012/5212 Chartplotter GPSMAP 4000/5000 Series Installation Instructions 
  • Garmin GPSMAP 4012 | Installation Instructions - Page 4
    Note: Stainless-steel screws may bind when screwed into fiberglass and overtightened. Garmin recommends applying an anti-galling, stainless antiseize lubricant to the screw before using. 12.Replace the mounting covers by snapping them into place.  GPSMAP 4000/5000 Series Installation Instructions
  • Garmin GPSMAP 4012 | Installation Instructions - Page 5
    correct operation. If you experience interference with other electronics, try a different location. When you verify correct operation, permanently mount the antenna. Below - OK Radar 3 ft. (1 m) VHF Radio Antenna GPS 17x Placement Considerations GPSMAP 4000/5000 Series Installation Instructions
  • Garmin GPSMAP 4012 | Installation Instructions - Page 6
    Mounting a GPS 17 Antenna You can surface mount the GPS 17 antenna or install it on a standard 1 in. OD pipe-threaded-pole marine mount (14 threads per inch-not included). Surface Mounting the GPS 17 Antenna 1. Cut out the Surface Mount Drilling Template provided on page 23, and tape it on the
  • Garmin GPSMAP 4012 | Installation Instructions - Page 7
    a Pole Mount The GPS 17x antenna can be surface mounted, installed on a standard 1 in. OD pipe-threaded-pole marine mount (14 threads-per-inch-not included), or even mounted under fiberglass. Surface Mounting the GPS 17x Antenna 1 Use the surface-mount bracket as your mounting template. • Use the
  • Garmin GPSMAP 4012 | Installation Instructions - Page 8
    the deck. 6. Connect the NMEA 2000 drop cable to the GPS 17x. 7. Route the cable away from sources of electronic interference, and connect it to your NMEA 2000 network. Adhesive pads Mounting surface GPS 17x antenna Under-deck mounting bracket  GPSMAP 4000/5000 Series Installation Instructions
  • Garmin GPSMAP 4012 | Installation Instructions - Page 9
    : If you are using more than one Garmin chartplotter over a Garmin Marine Network, do not wire more than one chartplotter to a GPS antenna. The GPS signal is shared between multiple chartplotters connected to a Garmin Marine Network. Garmin GPSMAP 4000/5000 Series Unit Power cable Wire color Fuse
  • Garmin GPSMAP 4012 | Installation Instructions - Page 10
    must also be connected to power or it will not function. See page 9. Note: One GPS antenna will provide position data for every device on the NMEA 2000 network. Do not connect multiple GPS antennas if you are using multiple chartplotters. 10 GPSMAP 4000/5000 Series Installation Instructions
  • Garmin GPSMAP 4012 | Installation Instructions - Page 11
    must also be connected to power or it will not function. See page 9. Note: One GPS antenna will provide position data for every device on the NMEA 2000 network. Do not connect multiple GPS antennas if you are using multiple chartplotters. GPSMAP 4000/5000 Series Installation Instructions 11
  • Garmin GPSMAP 4012 | Installation Instructions - Page 12
    the Garmin Marine Network. • Connect network components, such as a Garmin GMR radar, GSD sounder, or GDL XM Weather receiver to any chartplotter on the network or to an optional GMS 10 Network Port Expander. Data is shared between all chartplotters on the network. • BlueChart® g2 Vision cartography
  • Garmin GPSMAP 4012 | Installation Instructions - Page 13
    Sample Garmin Marine Network Setups: Garmin GPSMAP 4000/5000 series chartplotter Garmin GPSMAP 4000/5000 series chartplotter Marine Network with Two Chartplotters Garmin marine radar GDL 30/30A XM weather unit xxxx GSD 22 sounder unit xxxxxxxxxxxxxxxxxxxxxxx To transducer Garmin GPSMAP 4000/
  • Garmin GPSMAP 4012 | Installation Instructions - Page 14
    Garmin marine radar GSD 22 sounder unit xxxx GMS 10 marine network port expander xxxxxxxxxxxxxxxxxxxxxxx To transducer GDL 30/30A XM weather receiver Garmin GPSMAP 3000 series chartplotter Garmin GPSMAP 4000/5000 series chartplotter Connecting a GPSMAP 4000/5000 Series Chartplotter to an
  • Garmin GPSMAP 4012 | Installation Instructions - Page 15
    (pwr gnd) Black (data GND) Transmit A(+) transmit B(-) > > > > Gray Receive A(+) > > pink receive B(-) > Wiring to a NMEA 0183-compliant Device (AIS) NMEA 0183-compliant device (AIS) Garmin GPSMAP 4000/5000 series chartplotter wire color + - BATTERY 10-35 Vdc Wire Power cable NMEA
  • Garmin GPSMAP 4012 | Installation Instructions - Page 16
    input with support for the DPT (depth) or DBT, MTW (water temperature), and VHW (water temperature, speed, and heading) sentences. • Use the Communications section of the Configure menu on the GPSMAP 4000/5000 series chartplotter to set up NMEA 0183 communications. See the owner's manual for details
  • Garmin GPSMAP 4012 | Installation Instructions - Page 17
    0183-compliant device Garmin GPSMAP 4000/5000 series chartplotter Power cable NMEA 0183 Cable Wire see table for Fuse wire colors 7.5 A - device > > Wiring to Receive Data from a NMEA 0183-compliant Device With a Single Wire RX Connection GPSMAP 4000/5000 Series Installation Instructions 17
  • Garmin GPSMAP 4012 | Installation Instructions - Page 18
    is 100 mA, and a relay is needed to limit the current from the chartplotter to 100 mA. To select between visual and audible alerts, install a switch. Garmin GPSMAP 4000/5000 series chartplotter Power cable Wire Color Fuse 7.5 A - 42 V Red (power) Black (gnd) + Battery - 10-35 Vdc Horn NMEA
  • Garmin GPSMAP 4012 | Installation Instructions - Page 19
    the Garmin Marine Network. ➊ and ➋ VIDEO 1 and VIDEO 2 Inputs (RCA connectors) allow input from two separate NTSC/PAL compatible video devices, such as VCR, DVD, TV, or a video camera. The chartplotter can display one video input at a time or alternate between the two. See the owner's manual for
  • Garmin GPSMAP 4012 | Installation Instructions - Page 20
    card. If a software update SD card is not included, visit www.garmin.com to make sure your chartplotter software is up-to-date. To determine the version of software on your chartplotter, select or touch Configure > System > System Information. 20 GPSMAP 4000/5000 Series Installation Instructions
  • Garmin GPSMAP 4012 | Installation Instructions - Page 21
    Product Information Vessel Heading Speed - Water Referenced Water Depth Position - Rapid Update COG & SOG - Rapid Update GNSS Position Data GNSS Sats in View Wind Data Temperature GPSMAP 4000/5000 series chartplotters are NMEA 2000 certified. GPSMAP 4000/5000 Series Installation Instructions 21
  • Garmin GPSMAP 4012 | Installation Instructions - Page 22
    22 GPSMAP 4000/5000 Series Installation Instructions
  • Garmin GPSMAP 4012 | Installation Instructions - Page 23
    the mounting panel. Warning: Do not use this template to mount the GPS 17x antenna. This template is designed for the GPS 17 antenna only. To mount a GPS 17x antenna, use the surface-mount bracket as the template. See page 7 for more information. GPSMAP 4000/5000 Series Installation Instructions
  • Garmin GPSMAP 4012 | Installation Instructions - Page 24
    For the latest free software updates (excluding map data) throughout the life of your Garmin products, visit the Garmin Web site at www.garmin.com. August 2009 © 2009 Garmin Ltd. or its subsidiaries Garmin International, Inc. 1200 East 151st Street, Olathe, Kansas 66062, USA Garmin (Europe) Ltd.
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
GPSMAP
®
4000/5000 Series Installation Instructions
The GPSMAP 4000/5000 series chartplotter and GPS antenna must be properly installed according to the following instructions. You need the
appropriate fasteners, tools, and mounts listed in each section. These items are available at most marine dealers. Always wear safety goggles,
ear protection, and a dust mask when drilling, cutting, or sanding. When drilling or cutting, always check what is on the opposite side of the
surface. Mount the GPSMAP 4000/5000 series chartplotter in a location that provides a clear, glare-free view of the display and easy operation
of the controls or touch screen.
If you experience difficulty installing the chartplotter, seek the assistance of a professional installer;
or contact Garmin Product Support by phone at 913/397.8200 or 800/800.1020. Go to
www.garmin.com/support
. In Europe, contact
Garmin (Europe) Ltd. at 44/0870.8501241.
Before installing your GPSMAP 4000/5000 series chartplotter, confirm that the package contains the items listed on the box. If any parts are
missing, contact your Garmin dealer immediately.
WARNING
: See the
Important Safety and Product Information
guide in the product box for product warnings and other important
information.
To install the GPSMAP 4000/5000 series chartplotter, you must:
1. Mount the GPSMAP 4000/5000 series chartplotter (
page 1
).
2. Mount the GPS antenna (
page 5
).
3. Connect the GPSMAP 4000/5000 series device to power and to the GPS antenna (
pages 9–10
).
4. Ensure the chartplotter software is up-to-date (
page 20
).
Although they are not necessary to use the GPSMAP 4000/5000 chartplotter, this manual covers other installation options:
•
Connecting the chartplotter to other Garmin Marine Network compatible devices, such as a sounder or a radar (
page 12
).
•
Connecting the chartplotter to an existing NMEA 2000 network (
page 10
).
•
Connecting the chartplotter to other NMEA 0183-compatible devices such as a VHF radio with DSC (
page 15
).
•
Connecting the chartplotter to an external alarm (
page 18
).
•
Connecting the chartplotter to a video input source (
page 19
).
•
Connecting the chartplotter to an external video monitor (
page 19
).
Mounting the GPSMAP 4000/5000 Series Chartplotter
You can mount the GPSMAP 4000/5000 series chartplotters one of two ways. You can use the included bracket to bail mount the chartplotter, or
you can use the included template and hardware to flush mount the chartplotter.
NOTE:
You cannot bail mount the GPSMAP 5015/5215 chartplotters. Because of the larger size, you must flush mount a GPSMAP 5015/5215
chartplotter.
Bail Mounting the GPSMAP 4000/5000 Series Chartplotter
Use the included bracket to bail mount the GPSMAP 4000/5000 series chartplotter.
Tools required (not included):
•
Drill and drill bit
•
Screwdriver
•
Pencil
•
Mounting hardware (screws or nuts, washers, and bolts)
NOTE:
The mounting hardware (screws or nuts, washers, and bolts) are not included. The holes on the bail mount are
5
/
16
in. (7.9 mm) in diameter.
Choose mounting hardware that fits the holes in the bail mount and securely attaches it to your specific mounting surface. The size of the drill bit
required depends on the mounting hardware chosen.
August 2009
Part Number 190-00779-02 Rev. F
Printed in Taiwan