Garmin Tread Audio System Owners Manual
Garmin Tread Audio System Manual
 |
View all Garmin Tread Audio System manuals
Add to My Manuals
Save this manual to your list of manuals |
Garmin Tread Audio System manual content summary:
- Garmin Tread Audio System | Owners Manual - Page 1
TREAD® AUDIO SYSTEM Owner's Manual - Garmin Tread Audio System | Owners Manual - Page 2
the written consent of Garmin. Garmin reserves the right to change or improve its products and to make changes in the content of this manual without obligation to notify any person or organization of such changes or improvements. Go to www.garmin.com for current updates and supplemental information - Garmin Tread Audio System | Owners Manual - Page 3
Speakers and Brackets.. 11 Wiring 13 Wire Gauge Guide 13 Additional Speakers 13 Pairing and Setup 13 Support Center 18 Device Care 18 Cleaning the Outer Casing 18 Cleaning the Speakers and Brackets 18 Updating Device Firmware 18 Replacing the Wireless Remote Battery 19 Troubleshooting - Garmin Tread Audio System | Owners Manual - Page 4
- Garmin Tread Audio System | Owners Manual - Page 5
Getting Started WARNING See the Important Safety and Product Information guide in the product box for product warnings and other important information. You can permanently damage your ears and lose hearing if you listen to the - Garmin Tread Audio System | Owners Manual - Page 6
Tread Audio Box Mounting Considerations CAUTION In high ambient temperatures and after extended use, the device enclosure may reach temperatures deemed dangerous to touch. Therefore, you must install the device in a location where it is not touched during operation. NOTICE The storage and operating - Garmin Tread Audio System | Owners Manual - Page 7
Port Identification Item FUSE Description Contains the 15 A fuse for the LED outputs. Not used. Connects the device to the auxiliary in and line/subwoofer out wiring harness. Connects the device to the ground terminal wire (GND). Connects the device to the +12V terminal wire. Connects the - Garmin Tread Audio System | Owners Manual - Page 8
Speaker and LED Wiring Harness Wire and Connector Identification Wire Group Speaker zone 1 Wire Function Ignition Amplifier on Left (+) Left (-) Right (+) Right (-) 4 Wire Color/Number Red Blue White White with a black stripe Gray Gray with a black stripe Notes Connects to the vehicle accessory - Garmin Tread Audio System | Owners Manual - Page 9
Green Blue Addressable LED Wiring Considerations You can wire addressable LED lights to your Tread Audio Box. For more information, see the manual for your addressable LED lights. Compatible addressable LED types: • WS2812B • WS2813 Addressable LED LED Wire Color Wire Function Red +5V Power - Garmin Tread Audio System | Owners Manual - Page 10
RCA Wiring Harness Wire and Connector Identification Wire Function Wire Color/ Number Auxiliary in left Auxiliary in right Line out left Line out right Subwoofer out Notes Provides a red and white RCA stereo line input for audio sources, such as a CD or MP3 player. Provides a full-range output - Garmin Tread Audio System | Owners Manual - Page 11
Connecting the Device to Vehicle Power You should always confirm all electrical connections are secure and will not come loose while operating the device. NOTICE If the ignition wire is not used, do not tie the ignition to the positive terminal on the vehicle battery. Ground the ignition wire or - Garmin Tread Audio System | Owners Manual - Page 12
4 Connect the small ring end of the ground wire to the GND terminal on the device. 5 Tighten the screw on the GND terminal. You should confirm the screws cannot be loosened by hand. 6 Connect the small ring end of the included 12V cable to the +12V terminal on the device. 7 Tighten the screw on the - Garmin Tread Audio System | Owners Manual - Page 13
Item Description Zone 2 speakers Water-tight connection Zone 1 speakers Amplifier-on signal wire Powered amplifier Line out and subwoofer out Subwoofer Installation 9 - Garmin Tread Audio System | Owners Manual - Page 14
Speaker Zones You can group speakers in one area into speaker zones. This enables you to control the audio level of the each zone individually. Zones 1 and 2 are powered by the on-board amplifier. To use the RCA line output, you must connect an external amplifier. You can set the balance, tone, and - Garmin Tread Audio System | Owners Manual - Page 15
Mounting the Wireless Remote 1 Select an appropriate location for the remote control (Wireless Remote Mounting Considerations, page 10). 2 Test the range at the selected location by holding the wireless remote at the location, pressing a few buttons, and confirming the correct operation. 3 - Garmin Tread Audio System | Owners Manual - Page 16
6 Connect the speaker and LED wires (Wiring, page 13). 7 Place the connected wires in the channel on the base of the bracket bar. , and route the wires along the roll 8 Place the top of the bracket over the roll bar, and hold it against the base of the bracket. 9 Using a 5 mm hex driver or hex key - Garmin Tread Audio System | Owners Manual - Page 17
use a larger gauge of wire (Wire Gauge Guide, page 13). • You should make all of the wiring . Refer to the owner's manual for your stereo system at support.garmin.com for more information. Box device, press . 4 Follow the on-screen instructions to complete the pairing and setup process. The main - Garmin Tread Audio System | Owners Manual - Page 18
Tread app. 4 On your Tread Audio Box, press . 5 Follow the on-screen instructions to complete the pairing and setup process. The main app dashboard appears. After the devices See the Important Safety and Product Information guide in the product box for product warnings and other important information - Garmin Tread Audio System | Owners Manual - Page 19
Radio sources: Press to tune to the previous station. AUX sources: Press to decrease gain. Other sources: Press to skip to the beginning of the track or to the previous track. Radio sources: Press to tune to the next station. AUX sources: Press to increase gain. Other sources: Press to skip to the - Garmin Tread Audio System | Owners Manual - Page 20
as title, artist, album, station, or channel. Displays progress through the current media item. Displays playback controls. The controls change based on the service providing the media. Displays the current audio source. indicates the media is being played by another media app on your phone and sent - Garmin Tread Audio System | Owners Manual - Page 21
Enabling LED Groups By default, the controls for LED groups RGB 1 and RGB 2 are enabled. Enabling an LED group allows you to use the LED lighting controls for that group. You can enable the LED group for the Tread 6.5" XS-LED Tower Speakers or any additional speakers or addressable LEDs after you - Garmin Tread Audio System | Owners Manual - Page 22
Garmin Support Center Go to support.garmin.com for help and information, such as product manuals, frequently asked questions, videos, and customer support. When the update notification appears, follow the on-screen instructions to complete the update process. NOTE: Do not disconnect power during - Garmin Tread Audio System | Owners Manual - Page 23
Replacing the Wireless Remote Battery The remote uses one CR2032 lithium coin-cell battery. 1 Rotate the remote control, and remove it from the mount. 2 Rotate the battery compartment counter-clockwise until the line points to . 3 Wrap the end of a small flat screwdriver with tape. The tape - Garmin Tread Audio System | Owners Manual - Page 24
input level of the amplifier is matched to the output level of the stereo. For more information, see the manual for the amplifier. The LED lights will not turn on • Verify that all wiring connections are correct and periods of time may cause corrosion on the electrical contacts. 20 Troubleshooting - Garmin Tread Audio System | Owners Manual - Page 25
Device Information Tread Audio Box Specifications General Weight Water resistance Operating temperature range Storage temperature range Input voltage Current (max.) Current (muted) ANT wireless range Compass-safe distance Fuse Bluetooth wireless range 997 g (2.2 lbs.) IEC 60529 IPX7 (water), IEC - Garmin Tread Audio System | Owners Manual - Page 26
Tread 6.5" XS-LED Tower Speakers Specifications Max. power 200 W RMS power 50 W Sensitivity (1 W/1 m) 91 dB Frequency response From 80 Hz to 18 kHz Recommended amplifier power (RMS, playing music) From 20 to 150 W Nominal voice coil diameter 30 mm Impedance 4 ohms Operating - Garmin Tread Audio System | Owners Manual - Page 27
Dimensions 223 mm (813/16 in.) Ø 176 mm (615/16 in.) 180 mm (71/8 in.) Bracket Specifications Material Aluminum alloy with silicone pads Supported roll bar sizes From 33.4 mm (1.31 in.) to 50.8 mm (2.00 in.) outer diameter Device Information 23 - Garmin Tread Audio System | Owners Manual - Page 28
Bracket Side Dimensions 85 mm (33/8 in.) From 74 mm (27/8 in.) to 94 mm (311/16 in.) Bracket Top Dimensions 37 mm (17/16 in.) 48 mm (2 in.) 24 Device Information - Garmin Tread Audio System | Owners Manual - Page 29
Index C cleaning the device 18 D device, cleaning 18 S software, updating 18 T troubleshooting 20 Index 25 - Garmin Tread Audio System | Owners Manual - Page 30
support.garmin.com July 2022 GUID-8519D3E3-ACB5-4063-A5C1-0335CE7C87F6 v1
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
 |
 |
TREAD
®
AUDIO SYSTEM
Owner’s Manual