GE DLSR483GGWW Installation Instructions

Installation

Instructions

Gas Dryer

If you have any questions, call 1-800-GECARES (US) or 1-800-361-3400 (Canada)

or Visit our Web site at:

www. GEAppliances.com

MATERIALS YOU WILL NEED

LEVEL

Step 1

Verify Your Gas Installation (see section 2).

Step 2

Prepare the Area and Exhaust for Installation of

New Dryer (see section 1).

Step 3

Check and Insure the Existing External Exhaust is

Clean (see section 1) and Meets Attached Installation

Specifications (see section 6).

Step 4

Remove the Foam Shipping Pads (see section 1).

Step 5

Move the Dryer to the Desired Location.

Step 6

Level Your Dryer (see section 8).

Step 7

Connect the Gas Supply (see section 3) and check

for leaks (see section 4).

Step 8

Connect the External Exhaust (see section 7).

Step 9

Connect the Power Supply (see section 5).

Step 10

Check the Operation of the Power Supply, Gas

Connections, and Venting.

Step 11

Place the Owners Manual and the Installation

Instructions in a Location Where They Will Be

Noticed By the Owner.

For Alcove or Closet Installation see section 9.

For Bathroom or Bedroom Installation see section 10.

For Mobile or Manufactured Home see section 11.

8" PIPE WRENCH

D

E

S

I

G

N

C

E

R

T

I

F

I

E

D

08

In the state of Massachusetts, installation must be performed by a qualified

or licensed contractor, plumber, or gasfitter qualified or licensed by the state.

WARNING

RISK OF FIRE

• To reduce the risk of severe injury or death, follow all installation instructions.

• Clothes dryer installation must be performed by a qualified installer.

• Install the clothes dryer according to these instructions and in accordance with

local codes. In the absence of local codes, installation must comply with National

Fuel Gas Code, ANSIZ223.1/NFPA 54 or the Canadian Natural Gas and Propane

Installation Code, CSA B149.1.

• This dryer must be exhausted to the outdoors.

This act requires the governor of California to publish a list of substances known to the

state to cause cancer, birth defects or other reproductive harm and requires businesses to

warn customers of potential exposure to such substances. Gas appliances can cause minor

exposure to four of these substances, namely benzene, carbon monoxide, formaldehyde

and soot, caused primarily by the incomplete combustion of natural gas or LP fuels.

Properly adjusted dryers will minimize incomplete combustion. Exposure to these

substances can be minimized further by properly venting the dryer to the outdoors.

•

California Safe Drinking Water and Toxic Enforcement Act

•

Use only 4” rigid metal ducting for exhausting the clothes dryer to the outdoors.

• Do not install or store this appliance in any location where it could be exposed to

water and or weather.

• Save these instructions. (Installers: Be sure to leave these instructions with the

customer).

• DO NOT install a clothes dryer with flexible plastic ducting materials.

If flexible

metal (semi-rigid or foil-type) duct is installed, it must be UL-listed and installed

in accordance with the instructions found in "Connecting The Dryer To House

Vent" on page 6 of this manual.

Flexible ducting materials are known to collapse,

be easily crushed, and trap lint. These conditions will obstruct dryer airflow and

increase the risk of fire.

BEFORE YOU BEGIN

Read these instructions completely and

carefully.

•

IMPORTANT-

Save these

instructions for local inspector’s use.

•

IMPORTANT-

Observe

all governingcodes and ordinances.

•

Note to Installer

- Be sure to leave

these instructions with the customer.

•

Note to Customer

-

Keep these

instructions with your Use and Care

Book for future reference.

•

Before the old dryer is removed from

service or discarded, remove the dryer

door.

•

Service information and the wiring dia-

gram are located in the control console.

•

Do not allow children on or in the

appliance. Close supervision of child-

ren is necessary when the appliance is

used near children.

•

Install the dryer where the temp-

erature is above 50°F for satisfactory

operation of the dryer control system.

•

Inspect the dryer exhaust outlet and

straighten the outlet walls if they are

bent.

EXHAUST HOOD

FLEXIBLE GAS LINE CONNECTOR

SOAP SOLUTION

FOR LEAK DETECTION

PIPE

COMPOUND

DUCT TAPE

GLOVES

SAFETY GLASSES

4" DIAM METAL ELBOW

10" ADJUSTABLE WRENCHES

(x2)

4" DUCT CLAMPS

OR

4" SPRING CLAMPS

(x2)

(x2)

TOOLS YOU

WILL NEED

SLIP JOINT PLIERS

FLAT BLADE SCREWDRIVER

4" DIA. FLEXIBLE METAL (SEMI-RIGID)

UL LISTED TRANSITION DUCT

(IF NEEDED)

KIT WX08X10077 (INCLUDES 2 ELBOWS)

4" DIA. METAL DUCT

(RECOMMENDED)

4" DIA. FLEXIBLE METAL (FOIL TYPE)

UL LISTED TRANSITION DUCT

(IF NEEDED.)

GE DLSR483GGWW Installation Instructions

GE DLSR483GGWW Manual

GE DLSR483GGWW manual content summary: