GE GTD33GASKWW Installation Instructions
GE GTD33GASKWW Manual
 |
View all GE GTD33GASKWW manuals
Add to My Manuals
Save this manual to your list of manuals |
GE GTD33GASKWW manual content summary:
- GE GTD33GASKWW | Installation Instructions - Page 1
dryer is removed from service or discarded, remove the dryer door. • Service information and the wiring diagram are located in the control console. • Do not allow children on or in the appliance with the instructions found in "Connecting the Dryer to House Vent" later in this manual. Flexible vent - GE GTD33GASKWW | Installation Instructions - Page 2
low-level exposure to some of these substances, including benzene, carbon monoxide, formaldehyde and soot, caused primarily by the incomplete combustion of natural gas or LP fuels. Exposure to these substances can be minimized by properly venting the dryer to the outdoors. UNPACKING YOUR DRYER - GE GTD33GASKWW | Installation Instructions - Page 3
MAY REQUIRE GREATER THAN 0" OF REAR CLEARANCE. A 1" MINIMUM IS RECOMMENDED. Gas Dryers Only: • No other fuel burning appliance shall be installed in the same closet as a gas dryer. • The dryer must be disconnected from the gas supply piping during pressure testing at pressures greater than ½ psi - GE GTD33GASKWW | Installation Instructions - Page 4
Installation Instructions CONNECTING INLET HOSES CONNECTING INLET HOSES (on some models) To produce steam, the dryer must connect to until firmly seated. 5. Ensure the rubber flat washer is in place and attach the dryer's long inlet hose to one male end of the ''Y'' connector. Tighten by hand until - GE GTD33GASKWW | Installation Instructions - Page 5
Installation Instructions CONNECTING A GAS DRYER (skip for electric dryers) TOOLS YOU WILL NEED ˆ10" Adjustable wrenches (2) ˆ Flat-blade screwdriver ˆ8" Pipe wrench ˆ Level Before beginning the installation, turn off the circuit breaker(s) or remove the dryer's circuit fuse(s) at the - GE GTD33GASKWW | Installation Instructions - Page 6
assembly for use only with natural gas. Using conversion kit WE25X217, your local service organization can convert this dryer for use with propane (LP) gas. (To convert from propane (LP) to natural gas, conversion kit WE25X218 will be utilized.) ALL CONVERSIONS MUST BE MADE BY PROPERLY TRAINED - GE GTD33GASKWW | Installation Instructions - Page 7
Installation Instructions CONNECTING THE DRYER TO THE GAS SUPPLY A Install a female 3/8" NPT elbow at the end of the dryer gas inlet. Install a 3/8" flare union adapter to the female elbow. IMPORTANT: Use a pipe wrench to securely hold on to the end of the dryer gas inlet to prevent twisting the - GE GTD33GASKWW | Installation Instructions - Page 8
test. ELECTRICAL CONNECTION INFORMATION FOR GAS DRYERS (cont.) The dryer must be electrically grounded in accordance with local codes, or in the absence of local codes, with the National Electrical Code, ANSI/ NFPA 70 or Canadian Electrical Code, CSA C22.1 This appliance must be supplied with 120V - GE GTD33GASKWW | Installation Instructions - Page 9
Installation Instructions CONNECTING AN ELECTRIC DRYER (Skip for gas dryers and if your dryer already has a power cord attached) TOOLS YOU WILL NEED ˆSlip-joint pliers ˆPhillips screwdriver Before making the electrical connection, turn off the circuit breaker(s) or remove the dryer's circuit - GE GTD33GASKWW | Installation Instructions - Page 10
Instructions CONNECTING AN ELECTRIC DRYER (cont.) (Skip for gas dryers and if your dryer already has a power cord attached) ELECTRICAL CONNECTION INFORMATION FOR ELECTRIC DRYERS For electrical connections using a power cord: WARNING - Fire Hazard Use a new UL-listed 240V 30 amp dryer - GE GTD33GASKWW | Installation Instructions - Page 11
Instructions CONNECTING DRYER USING 4-WIRE CONNECTION (MUST BE USED FOR MOBILE HOME INSTALLATION) NOTE: Since January 1, 1996, the National Electrical Code requires that new constructions use a 4-wire connection to an electric dryer power supply cord kit marked for use with dryers and provided with - GE GTD33GASKWW | Installation Instructions - Page 12
exhaust length table. Failure to follow these instructions can result in death or fire. UL-LISTED FLEXIBLE METAL CLOTHES DRYER TRANSITION DUCT • If rigid metal cannot be used, then UL-LISTED flexible metal clothes dryer transition duct (GE parts - PM08X10085, WX08X10085 or WX08X10077) can be used - GE GTD33GASKWW | Installation Instructions - Page 13
Instructions dryer life. • Accumulate lint, creating a potential fire hazard. The correct exhaust installation is YOUR RESPONSIBILITY. Problems noted on the chart. • Internal elbows added for side or bottom vent conversions must be included in the total elbow count. • Any elbow greater than - GE GTD33GASKWW | Installation Instructions - Page 14
Installation Instructions EXHAUSTING THE DRYER (cont.) EXHAUST SYSTEM CHECKLIST HOOD OR WALL CAP • Terminate be tight to avoid leaks. The male end of each section of duct must point away from the dryer. • Duct joints should be made air- and moisture-tight by wrapping the overlapped joints with duct - GE GTD33GASKWW | Installation Instructions - Page 15
Instructions SIDE OR BOTTOM VENTING Dryer Exhaust to right of cabinet for Electric models only. Dryer Exhaust to left of cabinet for Gas and Electric models. Dryer Exhaust to the bottom of cabinet for Gas and Electric models. WARNING - Fire Hazard Close the back opening with cover plate (Kit - GE GTD33GASKWW | Installation Instructions - Page 16
to complete the exhaust system. Cover back opening with a plate (Kit WE1M454) available from your local service provider. Place dryer in final location. NEVER LEAVE THE BACK OPENING WITHOUT THE PLATE. (Kit WE1M454.) NOTE: If the dryer has been exposed to temperatures below freezing for an extended - GE GTD33GASKWW | Installation Instructions - Page 17
instructions all the way through before starting. • Handle parts carefully to avoid scratching paint. • Set screws down by their related parts dryer from its electrical outlet A REVERSING THE DOOR - SOLID DOOR MODELS DOOR instructions A or B for your model. A REVERSING THE DOOR - SOLID DOOR MODELS - GE GTD33GASKWW | Installation Instructions - Page 18
Installation Instructions REVERSING THE DOOR (cont.) A REVERSING THE DOOR - SOLID DOOR MODELS (cont.) 5 Mount the door on the 2 upper To return the door to the original setup, follow these instructions, swapping "left" and "right". When you finish Plug the dryer back into its electrical outlet. 18 - GE GTD33GASKWW | Installation Instructions - Page 19
Instructions REVERSING THE DOOR B REVERSING THE DOOR - GLASS PANEL DOOR MODELS 1 Open the door approximately 130 degrees. With a putty knife, remove the 4 plastic caps located along the left side of the front panel and set them aside. Plastic Cap (4) B REVERSING THE DOOR - GLASS PANEL DOOR MODELS - GE GTD33GASKWW | Installation Instructions - Page 20
side here Plastic caps Inner door B REVERSING THE DOOR - GLASS PANEL DOOR MODELS (cont.) 8 Mount the assembled door on the 2 upper left side hinge screws the original setup, follow these instructions, swapping "left" and "right". When you finish Plug the dryer back into its electrical outlet. 20 - GE GTD33GASKWW | Installation Instructions - Page 21
ón Secadora 05 Si tiene alguna pregunta, llame a 800.GE.CARES (800.432.2737) o visite nuestro sitio Web las instrucciones de "Cómo conectar la secadora a la ventilación doméstica" de este manual. Los materiales de los conductos flexibles a menudo se desploman, se aplastan y atrapan pelusas - GE GTD33GASKWW | Installation Instructions - Page 22
gas natural o combustibles de LP patas. Saque la literatura y la bolsa que contiene la información. DIMENSIONES APROXIMADAS 27" (68,8 cm) Y Pie Cúbico X Y 6.2 43 3/8" 26 se cubran las especificaciones de GE. GE recomienda enfáticamente el uso WX14X10007 2 Accesorio Kit completo (mangueras, - GE GTD33GASKWW | Installation Instructions - Page 23
ESPACIO EN LA PARTE TRASERA. 1" (2.54 CM) MÍNIMO ES LA RECOMENDADA. Secadoras a Gas Únicamente: • de ventilación DEBE SER METAL. • DEBE utilizarse el KIT 14-D346-33 para conectar bien la secadora a la ctrica, consulte la section. CABLES DE CORRIENTE: GE recomienda enfáticamente el uso de piezas espec - GE GTD33GASKWW | Installation Instructions - Page 24
goma se encuentre en su lugar y sujete el otro extremo de la manguera larga de entrada al conector de la válvula de llenado en la parte inferior del panel trasero de la secadora. Ajuste a mano hasta que esté firmemente asentada. 8. Abra el grifo de agua. 9. Controle la presencia de pérdidas - GE GTD33GASKWW | Installation Instructions - Page 25
de seguridad ˆCinta aislante ˆ Conducto de metal de 4" diámetro (recomendado) ˆ4" Placa de cubierta (Kit WE1M454) ˆGas adaptador (2), codo, y tapón de tubería Gire a la posición OFF (apagado) la válvula de gas de la secadora de la línea de suministro. Válvula de cierre Desconecte y elimine el - GE GTD33GASKWW | Installation Instructions - Page 26
para su uso con gas propano (LP). (Para convertir de gas propano (LP) al gas natural, se utilizará el kit de conversión WE25X218.) Nacional de Gas Combustible (National Fuel Gas Code), ANSI Z223.1/NFPA 54, o el Código de Instalación de Gas Natural o Propano (Natural Gas and Propane Installation Code - GE GTD33GASKWW | Installation Instructions - Page 27
ón cónica en la toma a rosca. NOTA: Aplique compuesto para tubería o cinta PTFE a las roscas del adaptador y a la toma. Conector nuevo de línea de gas de metal flexible Adaptador Codo NPT de 3/8" Los productos que no suministrados Adaptador Tapón de tubería npt de 1/8" para controlar la presión de - GE GTD33GASKWW | Installation Instructions - Page 28
DE PÉRDIDAS Nunca utilice una llama abierta para detectar pérdidas de gas. Controle todas las conexiones con una solución jabonosa o un elemento no provisto), ajustando el mismo al tornillo conectado a tierra de color verde en la parte trasera de la secadora, y a una conexión cañería metálica de - GE GTD33GASKWW | Installation Instructions - Page 29
SECADORA ELECTRICA (Sáltese si se trata de las secadoras a gas o si su secadora ya tiene un cable de alimentación ) ˆConducto de metal flexible de 4" de diámetro (si fuese necesario) ˆCinta aislante ˆKit de cable de energía de la secadora (no incluido con la secadora) Clasificado UL, de 120 - GE GTD33GASKWW | Installation Instructions - Page 30
Instrucciones de instalación CÓMO CONECTAR UNA SECADORA ELECTRICA (cont.) (Sáltese si se trata de las secadoras a gas o si su secadora ya tiene un cable de alimentación conectado) CONEXIÓN ELÉCTRICA INFORMACIÓN SOBRE LAS SECADORAS ELÉCTRICAS Para realizar conexiones eléctricas con - GE GTD33GASKWW | Installation Instructions - Page 31
de 3/4" reconocido por UL 4 conductores de cobre #10 AWG mínimo o kit de cable de suministro de energía de 120/240V 30A marcado para su del tomacorriente. 3. Quite la tapa del cable de energía ubicada en la parte trasera inferior. 4. Instale un alivio de tensión de 3/4 pulgadas reconocido por - GE GTD33GASKWW | Installation Instructions - Page 32
una chimenea, la salida de la cocina, ventilación de gas, pared, cielo raso, ático, espacio de rastreo, por UL puede ser utilizado. (GE partes - PM08X10085, WX08X10085 o WX08X10077.) transición que cumplan con "UL 2158A STANDARD FOR CLOTHES DRYER TRANSITION DUCT" (UL 2158A - Norma de conductos para - GE GTD33GASKWW | Installation Instructions - Page 33
la longitud permisible del sistema de escape. • En el cálculo de la longitud total del sistema de ventilación, debe agregar todas las partes rectas y codos del sistema (incluyendo el conducto de transición). LONGITUD DE ESCAPE LONGITUD MÁXIMA RECOMENDADA Tipos de campanas de escape Recomendado - GE GTD33GASKWW | Installation Instructions - Page 34
que la lavadora. Esto permitirá un acceso directo para poder efectuar la conexión de salida. Deslice el extremo del conducto de salida hacia la parte trasera de la secadora y sujete con cinta aislante o una abrazadera de mangueras. NOTA: Recomendamos el uso de un conducto de salida rígido de metal - GE GTD33GASKWW | Installation Instructions - Page 35
eléctricos. La secadora cuenta con una salida por la parte inferior del gabinete en modelos a gas y eléctricos. ADVERTENCIA - Riesgo de incendio Cierre la abertura trasera con la placa protectora (Kit WE1M454). Desconecte la secadora del suministro eléctrico. Use guantes y protectores para brazos - GE GTD33GASKWW | Installation Instructions - Page 36
secadora se encuentre nivelada de lado a lado y del frente a la parte trasera. Además ajuste las 2 patas antivuelco de las esquinas inferiores ón final. NUNCA DEJE LA ABERTURA TRASERA SIN LA PLACA EN SU LUGAR. (Kit WE1M454.) 3 INICIO DE LA SECADORA Presione el botón Power (Encendido). Power - GE GTD33GASKWW | Installation Instructions - Page 37
Instrucciones de instalación INVERSIÓN DE LA PUERTA Cómo cambiar el sentido de apertura de la puerta. NOTAS IMPORTANTES: • Lea todas las instrucciones antes de comenzar. • Manipule las piezas con cuidado para evitar rayar la pintura. • Coloque los tornillos cercanos a sus piezas correspondientes - GE GTD33GASKWW | Installation Instructions - Page 38
Instrucciones de instalación INVERSIÓN DE LA PUERTA (cont.) A INVERSIÓN DE LA PUERTA - MODELOS DE PUERTA SÓLIDA (cont.) 5 Monte la puerta sobre los 2 tornillos superiores del lado izquierdo, instalados en el paso 2. Mueva los tornillos de la bisagra aflojados en el paso 3 hacia los agujeros - GE GTD33GASKWW | Installation Instructions - Page 39
Instrucciones de instalación INVERSIÓN DE LA PUERTA B INVERSIÓN DE LA PUERTA - MODELOS CON PANEL DE CRISTAL 1 Abra la puerta aproximadamente 130 grados. Con una espátula, retire las 4 tapas de plástico ubicadas a lo largo del lado izquierdo del panel frontal y deje las mismas a un costado. Tapa de - GE GTD33GASKWW | Installation Instructions - Page 40
Instrucciones de instalación INVERSIÓN DE LA PUERTA (cont.) B INVERSIÓN DE LA PUERTA - MODELOS CON PANEL DE CRISTAL (cont.) 6 Quite y cambie las 2 tapas de plástico y la bisagras de la puerta exterior. Instale las tapas de plástico de un lado opuesto aquí Instalar bisagras de lado opuesto aquí
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
 |
 |
BEFORE YOU BEGIN
Read these instructions completely and carefully.
•
IMPORTANT
–
Save these instructions for local
electrical inspector’s use.
•
IMPORTANT
–
Observe all governing codes and
ordinances.
•
Install the clothes dryer according to the manufacturer’s
instructions and local codes.
•
Note to Installer –
Be sure to leave these instructions
with the Consumer.
•
Note to Consumer –
Keep these instructions for future
reference.
•
Clothes dryer installation must be performed by a
qualified installer.
•
This dryer
must
be exhausted to the outdoors.
•
Before the old dryer is removed from service or
discarded, remove the dryer door.
•
Service information and the wiring diagram are located
in the control console.
•
Do not allow children on or in the appliance. Close
supervision of children is necessary when the appliance
is used near children.
•
Proper installation is the responsibility of the installer.
•
Product failure due to improper installation is not
covered under the Warranty
.
•
Install the dryer where the temperature is above 50°F
for satisfactory operation of the dryer control system.
• Remove and discard existing plastic or metal foil duct
and replace with UL-listed duct.
Questions? Call 800.GE.CARES (800.432.2737) or visit our Web site at: GEAppliances.com
- Fire Hazard
WARNING
•
Clothes dryer installation must be performed by a
qualified installer.
•
Install the clothes dryer according to these
instructions and local codes.
•
DO NOT
install a clothes dryer with flexible plastic
venting materials. If flexible metal (semi-rigid or
foil-type) duct is installed, it must be UL-listed and
installed in accordance with the instructions found
in “Connecting the Dryer to House Vent” later in
this manual. Flexible vent materials are known to
collapse, be easily crushed and trap lint. These
conditions will obstruct dryer airflow and increase
the risk of fire.
•
DO NOT
install or store this appliance in any
location where it could be exposed to water or
weather.
•
To reduce the risk of severe injury or death, follow
all installation instructions.
•
Save these instructions. (Installers: Be sure to leave
these instructions with the customer.)
Installation
Dryers
Instructions
05
This is the safety alert symbol. This symbol alerts you to potential hazards that can kill you or hurt you and others.
All safety messages will follow the safety alert symbol and the word “DANGER”, “WARNING”, or “CAUTION”. These
words are defined as:
Indicates a hazardous situation which, if not avoided,
will
result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could
result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could
result in minor or moderate injury.
DANGER
WARNING
CAUTION
31-16775
10-15
GE
Printed in Mexico
234D2318P005