GE GTD42EASJWW Quick Specs
GE GTD42EASJWW Manual
 |
View all GE GTD42EASJWW manuals
Add to My Manuals
Save this manual to your list of manuals |
GE GTD42EASJWW manual content summary:
- GE GTD42EASJWW | Quick Specs - Page 1
. Dryer Exhausting Information: Use metal duct only, vertical and horizontal ducting. Back View For answers to your Monogram, GE Profile™ Series or GE® Series appliance questions, visit our website at geappliances.com or call GE Answer Center® service, 800.626.2000. 29 1/2" 26" 27" Power Cord - GE GTD42EASJWW | Quick Specs - Page 2
.com or call GE Answer Center® service, 800.626.2000. GE Dryer Vent Dryer exhausting information-use metal duct only vertical and horizontal ducting A A4 B A 2-1/2 4 B Domestic dryer models 2-1/2 GE Front Load Long Vent 7.0 cu. ft. capacity electric dryer (GFDL) Long Vent 6.1-7.4 cu. ft. capacity - GE GTD42EASJWW | Quick Specs - Page 3
-Cycle Signal - Alerts you when the load is done, so clothes can be removed before wrinkles set in 4 heat selections - Provide the right temperatures for your clothes-drying needs Up to 120-ft. venting capability - Provides flexible installation Model GTD42EASJWW - White Specification Revised 10/15
-
1 -
2 -
3
 |
 |
Listed by
Underwriters
Laboratories
Specification Revised 10/15
For answers to your Monogram, GE Profile
™
Series
or GE
®
Series appliance questions, visit our website
at geappliances.com or call GE Answer Center
®
service, 800.626.2000.
GTD42EASJ
GE
®
Series 7.2 Cu. Ft. Capacity Electric Dryer
22 1/2"
29 1/2"
26"
3 1/2"
1 3/4"
3 1/4"
8"
37 1/2"
44"
27"
5"
Power Cord 4 1/2"
11 3/4"
Side View
Rear View
5
Power
Cord Hole
4-1/2
POWER CORD LOCATIONS
BACK VIEW
SIDE VIEW
REAR VIEW
ELECTRIC DRYER RATING:
240V
5600W
24A
60Hz
208V
4400W
22A
60Hz
EXHAUST OPTION:
4-way rear, right, left and bottom.
CIRCUIT REQUIREMENTS:
An individual, properly-grounded branch circuit,
protected by a 30-amp circuit breaker or a time-delay fuse, is required.
NOTE:
Dryer wall outlet must be located within 36" of service cord entry and
acessible when dryer is mounted in position.
INSTALLATION INFORMATION:
For complete information, see installation
instructions packed with your dryer.
SPECIAL INSTALLATION REQUIREMENTS
ALCOVE OR CLOSET INSTALLATION:
- If your dryer is approved for installation in an alcove or closet, it will be stated
on a label on the dryer back.
- The dryer MUST be exhausted to the outside.
- Minimum clearances between dryer cabinet and adjacent walls or other surfaces
are: 0" either side; 3" front and rear.
- Minimum vertical space from floor to overhead cabinets, ceilings, etc. is 52".
- Closet doors must be louvered or otherwise ventilated and must contain a minimum
of 60 sq. in. of open area equally distributed. If this closet contains both a washer
and a dryer, doors must contain a minimum of 120 sq. in. of open area equally distributed.
- No other fuel-burning appliance shall be installed in the same closet with a gas dryer.
BATHROOM OR BEDROOM INSTALLATION
:
- The dryer MUST be exhausted to the outdoors.
- The installation must conform with the local codes, or in the absence of local codes,
with the National Electric Code and National Fuel Gas Code, ANSI Z223 for gas dryers.
MINIMUM CLEARANCES OTHER THAN ALCOVE OR CLOSET INSTALLATION:
- Minimum clearances to combustible surfaces are: 0" both sides; 3" rear.
DRYER EXHAUSTING INFORMATION:
Use metal duct only, vertical and horizontal ducting.
DIMENSIONS AND INSTALLATION INFORMATION
(IN INCHES)