GE JVB67HBB Installation Instructions
GE JVB67HBB Manual
 |
UPC - 084691082163
View all GE JVB67HBB manuals
Add to My Manuals
Save this manual to your list of manuals |
GE JVB67HBB manual content summary:
- GE JVB67HBB | Installation Instructions - Page 1
Installation Instructions Downdraft Vent System If you have questions, call 800.GE.CARES or visit our Website at: www.GEAppliances.com BEFORE YOU BEGIN Read these instructions completely and carefully. • IMPORTANT - Save these instructions for local inspector's use. • IMPORTANT - Observe all - GE JVB67HBB | Installation Instructions - Page 2
31⁄8″ 61⁄4″ 33⁄8″ 71⁄8″ 101⁄2″ A B 27″ 30″ Models 36″ Models A B 30″ 281⁄4″ 36″ 333⁄4″ WARNING! INSTALLATION SAFETY INSTRUCTIONS TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: A Installation work and electric wiring must be done by qualified person - GE JVB67HBB | Installation Instructions - Page 3
necessary clearances when planning installation. • Refer to your specific cooktop installation instruction for other appropriate Electric cooktops must operate from a separate 240V junction box. REMOTE SWITCH (for 36″ models only) The downdraft vent has a separate raise/lower switch. Plan to install - GE JVB67HBB | Installation Instructions - Page 4
Installation Instructions INSTALLATION POSSIBILITIES When the kitchen design calls for an against the wall installation, move 24″ deep base cabinet space. Base cabinet Filler panel Filler panel Base sink 30″ Min. for JVB37 36″ Min. for JVB67 18″ Base to sink 30″ to 42″ 18″ Countertop overhang - GE JVB67HBB | Installation Instructions - Page 5
to follow as a cutting guide. • Make sure sides of the opening are parallel and rear and front cuts are exactly perpendicular (right angle) to sides. 21⁄8″ 32 81⁄2″ 1 6 5 4 Planning Installation 30″ Electric and Gas Cooktops with Downdraft Vents 1 2 3 4 Model No. Overall Width Cooktop - GE JVB67HBB | Installation Instructions - Page 6
the countertop to follow as a cutting guide. • Make sure sides of the opening are parallel and rear and front cuts are exactly perpendicular to sides. 21⁄8″ 32 81⁄2″ 1 6 5 4 Planning Installation 36″ Electric and Gas Cooktops with Downdraft Vents 1 2 3 4 Model No. JP626 JP960 JP961 JP968 - GE JVB67HBB | Installation Instructions - Page 7
placed on the back of the cabinet wall where it may interfere with the downdraft plenum. See illustration. Do not leave gas or electrical connections within shaded area. 291⁄2″ 34″ for 36″ models 281⁄2″ for 30″ models Electrical outlet 12″ above cabinet floor NOTE: Do not use an extension cord or - GE JVB67HBB | Installation Instructions - Page 8
Installation Instructions DUCTWORK LENGTH AND DUCT FITTINGS NOTE: Do NOT EXCEED 150 EQUIVALENT FEET *Equivalent lengths of duct pieces are based on actual tests conducted by GE Evaluation Engineering and reflect requirements for good venting performance. See chart for CFM Duct Length. Duct Pieces - GE JVB67HBB | Installation Instructions - Page 9
Installation Instructions INSTALLING THE DOWNDRAFT VENT SYSTEM VENTING OPTIONS Side-to-Side Adjustments The assembly may be removed and turned 90° for a left or right side discharge. • The downdraft vent is shipped with the discharge outlet pointing straight down and can be changed to the left or - GE JVB67HBB | Installation Instructions - Page 10
Instructions 1 INSTALL THE DOWNDRAFT VENT Preferred method Secure the upper brackets with screws located on the side of case and attach to back of cabinet Secure the lower brackets to blower housing Place the downdraft vent into the countertop cutout, against the back side. A Secure the downdraft - GE JVB67HBB | Installation Instructions - Page 11
Installation Instructions INSTALLING THE DOWNDRAFT VENT SYSTEM 3 INSTALL THE RAISE/LOWER SWITCH NOTE: Step 3 is for 36″ models only. Skip this step if installing a 30″ model. WARNING - Disconnect electrical power from the unit before beginning switch installation parts and cabinet contents. 16 - GE JVB67HBB | Installation Instructions - Page 12
Instructions 4 CONNECT THE POWER Plug power cord into a properly grounded receptacle. INSTALL THE COOKTOP • With the downdraft in the "down" position, place the cooktop into the cutout. • Push the cooktop back until the back edge of the cooktop just barely touches the front edge of the downdraft - GE JVB67HBB | Installation Instructions - Page 13
Troubleshooting Tips Installation Instructions Operating Instructions Safety Instructions Before you call for service... Troubleshooting Tips Save time and money! Review the chart below first and you may not need to call for service. Problem the remote switch and vent body. Consumer Support 18
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
 |
 |
6
If you have questions, call 800.GE.CARES or visit our Website at: www.GEAppliances.com
REMOVE PACKAGING
Open the carton and remove parts package.
Check contents to be sure all pieces are
present. (The parts package may be attached
to the power cord.)
Remove the shipping materials. Remove the
carton and set aside. The carton can be used
as a pad when changing or adjusting vent
direction.
Installation
Downdraft Vent
Instructions
System
BEFORE YOU BEGIN
Read these instructions completely and
carefully.
•
IMPORTANT
—
Save these
instructions for local inspector’s use.
•
IMPORTANT
—
Observe all
governing codes and ordinances.
•
Note to Installer –
Be sure to leave these
instructions with the Consumer.
•
Note to Consumer –
Keep these
instructions for future reference.
•
Note –
This appliance must be properly
grounded.
•
Proper installation is the responsibility of
the installer.
•
Product failure due to improper installation
is not covered under the Warranty.
TOOLS YOU WILL NEED
Flat-blade screwdriver
Jig saw
Ductwork to suit
the installation
Carpenter square
PARTS INCLUDED
Remote raise/lower assembly (for 36
″
models only)
Stabilizing brackets
(all models) (4)
Wire box (2)
and screws (4)
Plastic strain
relief (2)
Wire and white
connector (1)
Switch cover
plate (1)
Attachment
bracket (1)
Pliers
Duct tape