GE JVM3670BF Installation Instructions

GE JVM3670BF Manual

GE JVM3670BF manual content summary:

  • GE JVM3670BF | Installation Instructions - Page 1
    Over the Range Microwave Oven Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com BEFORE YOU BEGIN Read these instructions completely and carefully. • IMPORTANT - Save these instructions for local inspector's use. • IMPORTANT - Observe all governing codes and ordinances
  • GE JVM3670BF | Installation Instructions - Page 2
    General information Important Safety Instructions 3 Electrical Requirements 3 Hood Exhaust 4, 5 Damage - Shipment/Installation 6 Parts Included 6 Tools You Will Need 7 Mounting Space 7 C Recirculating 19-22 Attach Mounting Plate to Wall 19 Preparation of Top Cabinet 19 Check Microwave
  • GE JVM3670BF | Installation Instructions - Page 3
    Instructions IMPORTANT SAFETY INSTRUCTIONS personal safety, the mounting surface must be capable of supporting the cabinet load, in addition to the added weight of microwave oven. The outlet box and supply circuit should be installed by a qualified electrician and conform to the National Electrical
  • GE JVM3670BF | Installation Instructions - Page 4
    Installation Instructions HOOD EXHAUST NOTE: Read these next two pages only if you plan to vent your exhaust to the outside. If you plan to recirculate the
  • GE JVM3670BF | Installation Instructions - Page 5
    Installation Instructions NOTE: If you need to install ducts, note that the total duct length of 31⁄4″ x 10″ rectangular or 6″ diameter round duct should not exceed 140
  • GE JVM3670BF | Installation Instructions - Page 6
    Installation Instructions DAMAGE - SHIPMENT/ INSTALLATION • If the unit is damaged in shipment, return the unit to the extra parts are included. ADDITIONAL PARTS PART Top Cabinet Template QUANTITY 1 Rear Wall 1 Template Installation 1 Instructions Separately 1 Packed Grease Filter 6
  • GE JVM3670BF | Installation Instructions - Page 7
    between the cabinets is greater than 30″, a Filler Panel Kit may be used to fill in the gap between the microwave oven and the cabinets. Your Owner's Manual contains the kit number for your model. • This microwave oven is for installation over ranges up to 36″ wide. • If you are going to vent your
  • GE JVM3670BF | Installation Instructions - Page 8
    1 PLACEMENT OF THE MOUNTING PLATE A. REMOVING THE MICROWAVE OVEN FROM THE CARTON/ REMOVING THE MOUNTING PLATE 1 Remove the installation instructions, filters, glass tray and the small hardware bag. Do not remove the Styrofoam protecting the front of the oven. 2 Fold back all 4 carton flaps
  • GE JVM3670BF | Installation Instructions - Page 9
    Installation Instructions C. DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET Plate position , install the mounting plate down the same distance as the front overhang depth. This will keep the microwave level. 1 Measure the inside depth of the front overhang. 2 Draw a horizontal line on the back
  • GE JVM3670BF | Installation Instructions - Page 10
    Installation Instructions D. ALIGNING THE WALL PLATE Hole A Hole C Centerline Notches Draw the stud. It is important to use at least one wood screw mounted firmly in a stud to support the weight of the microwave. Set the mounting plate aside. 4 Drill holes on the circles. If there is a stud,
  • GE JVM3670BF | Installation Instructions - Page 11
    Top Exhaust (Vertical Duct) B. Outside Back Exhaust (Horizontal Duct) C. Recirculating (Non-Vented Ductless) NOTE: This microwave is shipped assembled for Outside Top Exhaust (except for non-vented models). Select the type of ventilation required for your installation and proceed to that section
  • GE JVM3670BF | Installation Instructions - Page 12
    Installation Instructions A OUTSIDE TOP EXHAUST (Vertical Duct) INSTALLATION OVERVIEW A1. Attach Mounting Plate to Wall A2. Prepare Top Cabinet A3. Check Damper Operation A4. Mount Microwave Oven A5. Adjust Exhaust Adaptor A6. Connect Ductwork A1. ATTACH THE MOUNTING PLATE TO THE WALL To use
  • GE JVM3670BF | Installation Instructions - Page 13
    , following the instructions on the TOP CABINET TEMPLATE. CAUTION: Wear safety goggles when drilling holes in the cabinet bottom. A3. CHECK FOR PROPER DAMPER OPERATION Blower Plate Exhaust Adaptor (absent on models shipped for recirculation exhaust) Damper A4. MOUNT THE MICROWAVE OVEN FOR
  • GE JVM3670BF | Installation Instructions - Page 14
    Installation Instructions A4. MOUNT THE MICROWAVE OVEN (cont.) Cabinet Front Cabinet Bottom Shelf Filler Block Equivalent to Depth of Cabinet Recess Self-Aligning Screw Microwave Oven Top 4 Attach the microwave oven to the top cabinet. 5 Insert 2 self-aligning screws through outer top cabinet holes
  • GE JVM3670BF | Installation Instructions - Page 15
    oven: 1 Remove tape securing damper. 2 Remove and save screw that holds blower plate to microwave. Damper 3 Lift off the blower plate and attached adaptor from the microwave. Back of Microwave • Read the instructions on the REAR WALL TEMPLATE. • Tape it to the rear wall, lining up with the
  • GE JVM3670BF | Installation Instructions - Page 16
    Instructions B3. ATTACH THE MOUNTING PLATE TO THE WALL B4. USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET You need to drill holes for the top support instructions on the TOP CABINET TEMPLATE. CAUTION: Wear safety goggles when drilling holes in the cabinet bottom. B5. ADAPTING MICROWAVE
  • GE JVM3670BF | Installation Instructions - Page 17
    the screw. 9 Attach the exhaust adaptor to the rear of the oven by sliding it into the guides at the top center of the back of the oven. Back of Microwave Back of Microwave Adaptor Back of Microwave Guide Guide Locking Tabs Push in securely until it is in the lower locking tabs. Take care to
  • GE JVM3670BF | Installation Instructions - Page 18
    Installation Instructions B6. MOUNT THE MICROWAVE OVEN FOR EASIER INSTALLATION AND PERSONAL SAFETY, WE RECOMMEND THAT TWO PEOPLE INSTALL THIS MICROWAVE OVEN. IMPORTANT: Do not grip or use handle during of cabinet. 8 Install grease filter. See the Owner's Manual packed with the microwave. 18
  • GE JVM3670BF | Installation Instructions - Page 19
    Instructions C RECIRCULATING (Non-Vented Ductless) INSTALLATION OVERVIEW C1. Attach Mounting Plate to Wall C2. Prepare Top Cabinet C3. Check Microwave Assembly C4. Adjust Blower C5. Mount the Microwave support screws and a hole large enough for the power cord to fit through. • Read the instructions
  • GE JVM3670BF | Installation Instructions - Page 20
    Installation Instructions C3. CHECK MICROWAVE ASSEMBLY Exhaust Adaptor (absent on models shipped for recirculation exhaust) 5 Carefully pull out the blower unit. The wires will extend far enough to allow you to adjust the blower unit. Back of Microwave • Place the microwave in its upright
  • GE JVM3670BF | Installation Instructions - Page 21
    Installation Instructions C4. ADAPTING MICROWAVE BLOWER FOR RECIRCULATION (cont.) 7 Place the blower unit back into the opening. CAUTION: Do not pull or stretch the blower unit wiring. Make sure the wires are not pinched. NOTE: When mounting the microwave oven, thread power cord through hole in
  • GE JVM3670BF | Installation Instructions - Page 22
    and the top cabinet.) 8 Install grease filter. See the Owner's Manual packed with the microwave. C6. INSTALLING THE CHARCOAL FILTER 1 On 1400 and 1600 Series models, remove screws on front of grille using a #1 Phillips screwdriver. On 1800 Series models, remove screws on top front of grille using
  • GE JVM3670BF | Installation Instructions - Page 23
    the Owner's Manual. 2. Remove all packing material from the microwave oven. 3. Install turntable and ring in cavity. 4. Replace house fuse or turn breaker back on. 7. KEEP INSTALLATION INSTRUCTIONS FOR THE LOCAL INSPECTOR'S USE. 5. Plug power cord into a dedicated 15- to 20-amp electrical outlet
  • GE JVM3670BF | Installation Instructions - Page 24
    49- 40538 10-06 JR Printed in Malaysia
  • GE JVM3670BF | Installation Instructions - Page 25
    Instrucciones Horno microondas para de instalación colocar encima de la estufa ¿Preguntas? Llame 800.GE.CARES (800.432.2737) o visite nuestra página en la red en: ge.com ANTES DE EMPEZAR Lea estas instrucciones completa y cuidadosamente. • IMPORTANTE - Guarde estas instrucciones para el uso del
  • GE JVM3670BF | Installation Instructions - Page 26
    Instrucciones de instalación CONTENIDO Información general Instrucciones de seguridad importantes 3 Requisitos eléctricos 3 Campana de escape 4, 5 Daños - Envío / Instalación 6 Partes incluidas 6 Herramientas que necesitar 7 Espacio de montaje 7 Guía de instalación
  • GE JVM3670BF | Installation Instructions - Page 27
    debe estar conectado a un circuito de suministro del voltaje y frecuencia apropiados. El tamaño del alambre debe conformarse a los requisitos del National Electric Code o al código local en efecto para este índice de kilovatios. El cable eléctrico de alimentación y el interruptor deberán llevarse
  • GE JVM3670BF | Installation Instructions - Page 28
    Instrucciones de instalación CAMPANA DE ESCAPE NOTA: Lea las siguientes dos páginas solamente si planea ventilar el escape hacia el exterior. Si por el contrario planea recircular el aire de vuelta hacia el salón, continúe en la página 6. ESCAPE SUPERIOR EXTERNO (EJEMPLO SOLAMENTE) La siguiente
  • GE JVM3670BF | Installation Instructions - Page 29
    Instrucciones de instalación NOTA: Si usted necesita instalar conductos, tenga pendiente que la longitud total del conducto rectangular de 31⁄4″ x 10″ o el conducto redondo de 6″ de diámetro no debe sobrepasar 140 pies equivalentes. La ventilación externa requiere un CONDUCTO DE CAMPANA DE ESCAPE.
  • GE JVM3670BF | Installation Instructions - Page 30
    Instrucciones de instalación DAÑOS - ENVÍO / INSTALACIÓN • Si la unidad se daña durante el envío, devuelva la unidad al almacén donde la adquirió para su reparación o reemplazo. • Si el cliente daña la unidad, la reparación o el reemplazo es responsabilidad del cliente. • Si el instalador daña la
  • GE JVM3670BF | Installation Instructions - Page 31
    superficie de la estufa 30″, un "Filler Panel Kit" podría ser necesario para rellenar las brechas entre el horno y los mín. gabinetes. Su Manual del Propietario contiene Protector posterior de salpicaduras el número de kit para su modelo. • Este horno microondas es para ser instalado por encima
  • GE JVM3670BF | Installation Instructions - Page 32
    Instrucciones de instalación 1 CÓMO COLOCAR EL PLATO DE MONTAJE A. CÓMO REMOVER EL HORNO MICROONDAS DEL EMBALAJE / CÓMO REMOVER EL PLATO DE MONTAJE 1 Remueva las instrucciones de instalación, los filtros, la bandeja de cristal, y la bolsa pequeña del equipo. No remueva el protector frontal de
  • GE JVM3670BF | Installation Instructions - Page 33
    Instrucciones de instalación C. CÓMO DETERMINAR LA LOCALIZACIÓN DEL PLATO DE MONTAJE DEBAJO DE SU GABINETE Posición del plato - debajo de gabinetes de fondo plano Posición del plato - debajo de gabinetes de fondo apoyado en un marco Las orejillas del plato de montaje tocan el fondo del gabinete
  • GE JVM3670BF | Installation Instructions - Page 34
    Instrucciones de instalación D. CÓMO ALINEAR EL PLATO DE MONTAJE SOBRE LA PARED Agujero A Agujero C Muescas de la línea del centro Trace una línea vertical en la pared a partir del centro del gabinete superior Agujero B Area E Agujero D PRECAUCIÓN: Use guantes de protección para evitar
  • GE JVM3670BF | Installation Instructions - Page 35
    ÓN (SIN CONDUCTO DE VENTILACIÓN) Ver página 19 11 Un Kit de accesorios de filtro de carbonilla es necesario para el sistema sin ventilación. (Consulte su Manual del Propietario para obtener el número del kit.)
  • GE JVM3670BF | Installation Instructions - Page 36
    Instrucciones de instalación A ESCAPE SUPERIOR EXTERIOR (Conducto vertical) PERSPECTIVA GENERAL DE LA INSTALACIÓN A1. Como adherir el plato de montaje a la pared A2. Prepare el gabinete superior A3. Inspeccione la operación del regulador de tiro.
  • GE JVM3670BF | Installation Instructions - Page 37
    Instrucciones de instalación A2. USE LA PLANTILLA DEL GABINETE SUPERIOR PARA LA PREPARACIÓN DEL GABINETE Deberá perforar agujeros para los tornillos de apoyo superiores, un agujero suficientemente grande para que el cable eléctrico quepa, y un recorte lo suficientemente grande como para que el
  • GE JVM3670BF | Installation Instructions - Page 38
    aprieta los tornillos, mantenga el horno microondas en su lugar contra la pared y el gabinete superior.) 8 Instale el filtro de grasa. Ver el Manual del Propietario que viene con el horno microondas. 1 Extienda el conducto de la casa hacia abajo para conectarlo con el adaptador de escape. 2 Selle
  • GE JVM3670BF | Installation Instructions - Page 39
    Instrucciones de instalación B ESCAPE POSTERIOR EXTERNO (Conducto horizontal) PERSPECTIVA GENERAL DE LA INSTALACIÓN B1. Prepare la pared posterior B2. Remueva el adaptador de escape B3. Pegue el plato de montaje a la pared B4. Prepare el
  • GE JVM3670BF | Installation Instructions - Page 40
    Instrucciones de instalación B3. CÓMO ADHERIR EL PLATO DE MONTAJE A LA PARED B4. USE LA PLANTILLA DEL GABINETE SUPERIOR PARA PREPARAR EL GABINETE SUPERIOR Necesita perforar agujeros para los tornillos de apoyo superiores y un agujero suficientemente grande para que el cable eléctrico quepa. Pegue
  • GE JVM3670BF | Installation Instructions - Page 41
    Instrucciones de instalación B5. CÓMO ADAPTAR EL CALEFACTOR DEL MICROONDAS PARA EL ESCAPE EXTERIOR (continuación) 3 Rote la unidad 180° en sentido contrario a las agujas del reloj. Antes de la rotación Después de la rotación 6 Coloque la unidad del calefactor de nuevo en la abertura. DESPUES:
  • GE JVM3670BF | Installation Instructions - Page 42
    la pared y el gabinete superior.) 2 Gire el frente del horno contra el fondo del gabinete. 8 Instale el filtro de grasa. Ver el Manual del Propietario que viene con el horno microondas. 3 Inserte un tornillo de autoalineación a través del agujero central superior del gabinete. Asegure el horno
  • GE JVM3670BF | Installation Instructions - Page 43
    Instrucciones de instalación C RECIRCULACIÓN (Sin conducto de ventilación) PERSPECTIVA GENERAL DE LA INSTALACIÓN C1. Pegue el plato de montaje a la pared C2. Prepare el gabinete superior C3. Inspeccione la ensambladura del microondas C4. Ajuste el
  • GE JVM3670BF | Installation Instructions - Page 44
    Instrucciones de instalación C3. INSPECCIONE LA ENSAMBLADURA DEL MICROONDAS Adaptador de escape (ausente en los modelos enviados con escape de recirculación) 5 Cuidadosamente tire del calefactor. Los alambres se extenderán lo suficiente para permitirle que usted ajuste la unidad del calefactor.
  • GE JVM3670BF | Installation Instructions - Page 45
    Instrucciones de instalación C4. CÓMO ADAPTAR EL CALEFACTOR DEL MICROONDAS PARA LA RECIRCULACIÓN (continuación) 7 Coloque la unidad del calefactor de nuevo en la abertura. PRECAUCIÓN: No tire ni estire los cables del calefactor. Cerciórese de que los alambres no están pellizcados. NOTA: Cuando se
  • GE JVM3670BF | Installation Instructions - Page 46
    , deslice la rejilla hacia la izquierda y tire de ella directamente hacia afuera. Filtro de carbonilla 8 Instale el filtro de grasa. Ver el Manual del Propietario que viene con el horno microondas. 4 Instale el filtro de carbonilla. Cuando está instalado correctamente, la malla del filtro deber
  • GE JVM3670BF | Installation Instructions - Page 47
    en la cavidad. 4. Reemplace el fusible de la casa o encienda de nuevo el interruptor. Cerciórese de que existe una conexión a tierra apropiada 6. Lea el Manual del Propietario. 7. GUARDE ESTAS INSTRUCCIONES PARA EL USO DEL INSPECTOR LOCAL. 23
  • GE JVM3670BF | Installation Instructions - Page 48
    49- 40538 10-06 JR Impreso en Malasia
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48

Questions? Call 800.GE.CARES (800.432.2737)
or
Visit our Website at:
ge.com
READ CAREFULLY.
KEEP THESE INSTRUCTIONS
.
Installation
Over the Range
Instructions
Microwave Oven
Read these instructions completely and carefully.
IMPORTANT –
Save these
instructions for local inspector’s use.
IMPORTANT –
Observe all
governing codes and ordinances.
Note to Installer –
Be sure to leave these
instructions with the Consumer.
BEFORE YOU BEGIN
Note to Consumer –
Keep these
instructions for future reference.
Skill level
– Installation of this appliance requires
basic mechanical and electrical skills.
Proper installation is the responsibility of the installer.
Product failure due to improper installation is not
covered under the Warranty.
For a Spanish version of this manual, visit our Website at ge.com.
Para consultar una version en español de este manual de instrucciones, visite nuestro sitio
de internet ge.com.