GE PT7550SFSS Installation Instructions

GE PT7550SFSS Manual

GE PT7550SFSS manual content summary:

  • GE PT7550SFSS | Installation Instructions - Page 1
    Installation Instructions 27" & 30" Electric Built-In Wall Ovens Questions? Call 1.800.GE.CARES (1.800.432.2737) or visit www.GEAppliances.com In Canada, call 1.800.561.3344 or visit www.GEAppliances.ca BEFORE YOU BEGIN Read these instructions completely and carefully. • IMPORTANT - Save these
  • GE PT7550SFSS | Installation Instructions - Page 2
    ) Opening Between Inside Walls Must be at Least 28-1/2" (72.4 cm) Wide D 22" (55.9 cm) Min. to Bottom of Junction Box F C G E Cutout Depth 23-1/2" (59.7 cm) Min. Side-by-Side Installations Install two ovens in separate cutouts. Center Line Center Line 30.5" (77.5 cm) 30" models 27" (68.58
  • GE PT7550SFSS | Installation Instructions - Page 3
    (119.4 cm) 12" (30.5 cm) 31-10856-1 04-13 GE 2 D CUTOUT FOR INSTALLATION OVER A WARMING DRAWER NOTE: Install the oven only with specific models listed on the label located on top of the oven. NOTE: Additional clearances between cutouts may be required. Check to be sure the oven supports above the
  • GE PT7550SFSS | Installation Instructions - Page 4
    3 PEDESTAL RAIL INSTALLATION (DOUBLE OVENS ONLY) A. Place one pedestal rail on each cabinet runner or centered on opposite side of solid cabinet bottom flush with side of cabinet opening. Locate
  • GE PT7550SFSS | Installation Instructions - Page 5
    Code requires that new construction (not existing) utilize a four-conductor connection to an electric oven. When installing an electric oven in new construction, a mobile home, recreational vehicle or an area where local codes prohibit grounding through the neutral conductor, refer to the section
  • GE PT7550SFSS | Installation Instructions - Page 6
    (91 kg); and for a double oven, the platform must support 375 lbs. (170 kg). Connect the flexible conduit to the electrical junction box as shown below*. Position the conduit in such a manner that it will lie behind the unit in a natural loop when the oven is installed. You will need to purchase an
  • GE PT7550SFSS | Installation Instructions - Page 7
    trim lip must be placed under flange of bottom air duct. SWO's and DWO installations without pedestal DWO's with pedestals IMPORTANT: If this unit is ever removed from the cabinet or the oven is ever pulled out for service, the bottom trim must be removed first or damage to the trim will occur.
  • GE PT7550SFSS | Installation Instructions - Page 8
    guides (if applicable) are installed correctly and oven racks function smoothly. OPERATION CHECKLIST • Turn on the power to the oven (refer to your Owner's Manual). Verify that the bake and broil units and all cooking functions operate properly. • See your Owner's Manual for the troubleshooting
  • GE PT7550SFSS | Installation Instructions - Page 9
    Hornos de pared eléctricos empotrados de 27" y 30" ¿Preguntas? Llame al 1.800.GE.CARES (1.800.432.2737) o visite GEAppliances.com de encimera o debajo de las estufas especificadas. Vea la etiqueta de la parte superior del horno para consultar los modelos aprobados. INSTALACIONES DE HORNO DOBLE Puede
  • GE PT7550SFSS | Installation Instructions - Page 10
    72,4 cm) D 22" (55,9 cm) mín. hasta la parte inferior de la caja de conexiones F C G E Profundidad de la abertura - 23-1/2" (59,7 cm) mínimo Instalaciones lado a lado Instale dos hornos en aberturas separadas. Línea central Línea central 30.5" (77,5 cm) modelo 30" 27" (68.58 cm) modelo 27
  • GE PT7550SFSS | Installation Instructions - Page 11
    CALENTADOR NOTA: Instale el horno sólo con los modelos específicos listados en la etiqueta ubicada en la parte superior del horno desde el piso 131⁄4" (33,7 cm) 12" (30,5 cm) 12" (30,5 cm) Continúe en la sección 3. 31-10856-1 04-13 GE Continúe a la Sección 3 para conocer detalles del DWO
  • GE PT7550SFSS | Installation Instructions - Page 12
    riel con pedestal en cada rodadura del gabinete o centrado en el lado opuesto de la parte inferior del gabinete sólido nivelado con el lateral de la abertura del gabinete. Ubique cada riel de modo que la parte frontal de los mismos se encuentre detrás del lado frontal de la abertura del gabinete
  • GE PT7550SFSS | Installation Instructions - Page 13
    conexión de cuatro conductores a un horno eléctrico. Cuando instale un horno eléctrico en una construcción nueva, una casa rodante 6,3 KW-8,3 KW 8,4 KW-10,4 KW Tamaño de circuito recomendado (dedicado) 20 Amp 30 Amp 40 Amp 50 Amp NO acorte el conducto flexible. La abrazadera del alivio de tensión
  • GE PT7550SFSS | Installation Instructions - Page 14
    para su modelo. Para verificar la disponibilidad o solicitar piezas, llame al 1.800.GE.CARES. 9 DESLICE EL HORNO DENTRO DE LA ABERTURA • Levante el horno códigos locales, utilizando tapones de alambre. C. Instale la tapa de la caja de conexiones. Cables a tierra y neutrales Tapa de la
  • GE PT7550SFSS | Installation Instructions - Page 15
    10 INSTALE EL HORNO ADVERTENCIA: Deben utilizarse tornillos de montaje. Si no lo hace, el provistos. El labio de la cubierta inferior deberá ser ubicado debajo de la brida de la parte inferior del conducto de aire. Instalaciones SWO y DWO sin pedestal DWO sin pedestales IMPORTANTE: Si esta
  • GE PT7550SFSS | Installation Instructions - Page 16
    un círculo natural cuando el horno sea instalado. C. Instale las guías usando las 8 tuercas de montaje provistas. 13 de la bisagra bien colocada en la parte inferior de la ranura de la bisagra Ranura Accione la energía del horno (consulte el Manual del propietario). Verifique que las unidades de
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16

BEFORE YOU BEGIN
Read these instructions completely and
carefully.
IMPORTANT —
Save these instructions
for local inspector’s use.
IMPORTANT —
Observe all governing
codes and ordinances.
Note to Installer –
Be sure to leave these
instructions with Consumer.
Note to Consumer –
Keep these instructions
for future reference.
Skill level –
Installation of this appliance
requires a qualified installer or electrician.
Proper installation is the responsibility
of the installer.
Product failure due to improper installation
is not covered under Warranty.
Product is for indoor use only.
Installation Instructions
27” & 30” Electric Built-In Wall Ovens
FOR YOUR SAFETY:
WARNING
:
Before beginning the installation, switch power off at the service panel and
lock the service disconnecting means to prevent power from being switched on accidentally. When the
service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag,
to the service panel.
Be sure the oven is securely installed in a cabinet that is firmly attached to the house structure.
Weight on the oven door could cause the oven to tip and result in injury. Never allow anyone to climb, sit,
stand or hang on the oven door.
Make sure the wall coverings, counters and cabinets around the oven can withstand the heat
(up to 200°F [93.3°C]) generated by the oven.
Questions?
Call 1.800.GE.CARES (1.800.432.2737) or visit www.GEAppliances.com
In Canada, call 1.800.561.3344 or visit www.GEAppliances.ca
MATERIALS YOU MAY NEED
Junction Box
Wire Nuts
Strain Relief Clamp for 1/2” Conduit
TOOLS YOU MAY NEED
1/8” Drill Bit and Electric or Hand Drill
Phillips Screwdriver
Wire Strippers
1
REMOVE PACKAGING MATERIALS
Failure to remove packaging materials could result in damage to the appliance. Remove all packing
parts from oven, racks and heating elements. Remove protective film and labels on the outer door
and control panel. Also, remove plastic on trims and panel, all tape around the oven and any shipping
screws securing the oven to the base pad. Open oven door and remove literature pack and oven
racks. Remove the bottom trim from the top of the oven. It will be installed at the end of the installation
process. The trim is wrapped separately and taped to the top of the unit. Remove pedestal rails from
seperate box and set aside (30” Double Wall Ovens Only).
2
PREPARE THE OPENING
NOTE:
If the cabinet does not have a solid bottom, two
braces or runners must be installed to support the weight
of the oven. For single ovens, the runners and braces
must support 200 lbs (91 kg). For double ovens, the
runners and braces must support 375 lbs. (170 kg).
NOTE:
If marks, blemishes or the cutout opening are
visible above the installed oven, it may be necessary to
add wood shims under the runners and front trim until
the marks or opening are covered.
NOTE:
If the cabinet does not have a front frame and
the sides are less than ¾” (1.9 cm) thick, shim both sides
equally to establish the cutout width.
ATTENTION INSTALLER:
All electric wall ovens must be hard-wired (direct-wired) into an
approved junction box. A plug and receptacle is NOT permitted on these products.
Suitable
Bracing
to Support
Runners
C
L
2" x 4" (5 cm x 10 cm)
or Equivalent Runners Level
with Bottom of Cutout
and Flush with Sides of Cutout
DESIGN INFORMATION
SINGLE OVEN INSTALLATIONS
The single oven may be installed in a cabinet alone or above a warming drawer. The single oven may also
be installed below a countertop or below specified cooktops. See the label on top of the oven for approved
models.
DOUBLE OVEN INSTALLATIONS
A double oven may be installed in a cabinet alone or above a warming drawer. See the label on top of the
oven for approved models.
IMPORTANT:
Always refer to individual installation instructions packed with each product for specific
requirements.