Gigabyte D120-S3G Manual

Gigabyte D120-S3G Manual

Gigabyte D120-S3G manual content summary:

  • Gigabyte D120-S3G | Manual - Page 1
    GND 2 +12V 3 Sense 4 4 Speed Control ML00-AR0 Quick Reference Guide P/N: Battery Cable Connector No. Pin Define 2 1 1 Power 2 5 RXN  The default network configuration is DHCP mode, 7 to manually configure the IP address, please configure static IP in the U-Boot configuration
  • 1

ML00-AR0 Quick Reference Guide
Front Panel
Rear I/O Connector
12V ATX
SATA 6Gb/s Connectors
FAN Connectors
Reset Bu°on Header
Ba°ery Cable Connector
Front Panel Power
Bu°on Header
State
Description
Green On
10Gbps data arte
Yellow On
1Gbps data arte
Off
State
Description
Yellow On
1Gbps data arte
Green On
100Mbps data arte
10Mbps data arte
1
1
16
10
15
2
1
9
2
No.
Pin Define
1
GND
2
GND
3
+12V
4
+12V
No.
Pin Define
1
GND
2
+12V
3
Sense
4
Speed Control
No.
Pin Define
1
Power
2
GND
No.
Pin Define
1
SW_RESET_N
2
GND
No.
Pin Define
1
FP_PWR_BTN_N
2
GND
No.
Pin Define
1
GND
2
TXP
3
TXN
4
GND
No.
Pin Define
5
RXN
6
RXP
7
GND
1
1
1
1
2
1
2
2
4
1
7
7
HDD3 (Top)
HDD2 (Bu°om)
HDD1 (Top)
HDD0 (Bu°om)
HDD5 (Top)
HDD4 (Bu°om)
HDD7 (Top)
HDD6 (Bu°om)
HDD9 (Top)
HDD8 (Bu°om)
HDD11 (Top)
HDD10 (Bu°om)
HDD13 (Top)
HDD12 (Bu°om)
HDD15 (Top)
HDD14 (Bu°om)
No.
Pin Define
1
SMB_SCL
2
+5V_SB
3
SMB_SDA
4
GND
5
No Connect
6
Over Temperature Protec±on
7
MGNT_SCL
8
UBOOT_OK
9
MGNT_SDA
10
All Power OK
11
PS_ON#
12
Reset Bu°on
13
Front Panel Bu°on+
15
UART_Rx
16
UART_Tx
No.
Pin Define
1
Power bu°on/LED
2
LAN ports
3
SFP+ LAN ports
Speed LED
Link/Ac±vity
LED
Speed LED
Power bu°on/LED:
Link/Ac±vity
LED
LAN
No.
Pin Define
1
Fan Sense
2
SFP LAN1 LED
3
Front Panel HDD LED+
4
SFP LAN2 LED
5
LAN2 ACT LED+
6
HDD ACT LED+
7
LAN1 ACT LED+
8
No Connect
9
No Connect
10
SMB Alert
2
4
3
Green On
Off
Description
System is powered on
System is powered off
1
3
2
1
3
2
User must self-prepare console cable to access
ML00-AR0 motherboard control to configure its software.
ML00-AR0 (board or system ), was not able to log
ECC DIMM error through BMC.
The default network configuration is DHCP mode,
to manually configure the IP address, please configure static IP
in the U-Boot configuration.
P/N: