Gigabyte H370M D3H GSM RAID Setup Guide
Gigabyte H370M D3H GSM Manual
 |
View all Gigabyte H370M D3H GSM manuals
Add to My Manuals
Save this manual to your list of manuals |
Gigabyte H370M D3H GSM manual content summary:
- Gigabyte H370M D3H GSM | RAID Setup Guide - Page 1
Configuring a RAID Set Configuring SATA Controllers 2 Installing the RAID/AHCI Driver and Operating System 16 Installing an Intel® Optane™ Memory 19 - 1 - - Gigabyte H370M D3H GSM | RAID Setup Guide - Page 2
Configure SATA controller mode in BIOS Setup. C. Configure a RAID array in RAID BIOS. (Note 1) D. Install the RAID/AHCI driver and operating system. Before you driver disk. •• A USB thumb drive. Configuring SATA Controllers A. Installing hard drives Install the hard drives/SSDs in the Intel® Chipset - Gigabyte H370M D3H GSM | RAID Setup Guide - Page 3
computer and press to enter BIOS Setup during the POST (Power-On Self-Test). Go to Peripherals\SATA And RST Configuration, make sure SATA Controller(s) is enabled. To create RAID, set SATA Mode Selection to Intel RST Premium With Intel Optane System Acceleration (Figure 1). Figure 1 Step - Gigabyte H370M D3H GSM | RAID Setup Guide - Page 4
C-1. Using EZ RAID GIGABYTE motherboards provide you with the EZ RAID feature, allowing you to quickly configure a RAID array with simplified steps. Step 1: After restarting the computer, enter the BIOS Setup and go to Peripherals. Press on the EZ RAID item. Select the type of hard drives - Gigabyte H370M D3H GSM | RAID Setup Guide - Page 5
, and array capacity, etc. (Figure 4). Figure 4 Delete RAID Volume To delete a RAID array, press on the volume to be deleted on the Intel(R) Rapid Storage Technology screen. After entering the RAID VOLUME INFO screen, press on Delete to enter the Delete screen. Press on Yes - Gigabyte H370M D3H GSM | RAID Setup Guide - Page 6
C-2. UEFI RAID Configuration Step 1: In BIOS Setup, go to BIOS and set CSM Support to Disabled (Figure 6). Save the changes and exit BIOS Setup. Figure 6 Step 2: After the system reboot, enter BIOS Setup again. Then enter the Peripherals\Intel(R) Rapid Storage Technology sub-menu (Figure 7). Figure - Gigabyte H370M D3H GSM | RAID Setup Guide - Page 7
Intel(R) Rapid Storage Technology menu, press on Create RAID Volume to enter the Create RAID Volume screen. Enter a volume name with 1~16 letters (letters cannot be special characters) under the Name item and press . Then, select a RAID level (Figure 8). RAID levels supported include - Gigabyte H370M D3H GSM | RAID Setup Guide - Page 8
setting the capacity, move to Create Volume and press to begin. (Figure 10) Figure 10 After completing, you'll be brought back to the Intel(R) Rapid Storage Technology screen. Under RAID Volumes you can see the new RAID volume. To see more detailed information, press on the volume to - Gigabyte H370M D3H GSM | RAID Setup Guide - Page 9
Delete RAID Volume To delete a RAID array, press on the volume to be deleted on the Intel(R) Rapid Storage Technology screen. After entering the RAID VOLUME INFO screen, press on Delete to enter the Delete screen. Press on Yes (Figure 12). Figure 12 - 9 - - Gigabyte H370M D3H GSM | RAID Setup Guide - Page 10
Configuring Legacy RAID ROM Enter the Intel® legacy RAID BIOS setup utility to configure a RAID array. Skip this step and proceed with the installation of Windows operating system for a non-RAID configuration. Step 1: In BIOS Setup, go to BIOS and set CSM Support to Enabled and Storage Boot Option - Gigabyte H370M D3H GSM | RAID Setup Guide - Page 11
press . Then, select a RAID level (Figure 15). RAID levels supported include RAID 0, RAID 1, RAID 10, and RAID 5 (the selections the stripe block size, press . Intel(R) Rapid Storage Technology - Option ROM - 16.0.2.3402 Copyright (C) Intel Corporation. All Rights Reserved. [ CREATE - Gigabyte H370M D3H GSM | RAID Setup Guide - Page 12
(Figure 17). Intel(R) Rapid Storage Technology - Option ROM - 16.0.2.3402 Copyright(C) Intel Corporation. All Rights (Figure 18) Intel(R) Rapid Storage Technology - Option ROM - 16.0.2.3402 Copyright (C) Intel Corporation. All To exit the RAID BIOS utility, press or select 6. Exit in MAIN - Gigabyte H370M D3H GSM | RAID Setup Guide - Page 13
recovery drive is hidden. Step 1: Select Create RAID Volume in MAIN MENU and press (Figure 19). Intel(R) Rapid Storage Technology - Option ROM - 16.0.2.3402 Copyright (C) Intel Corporation. All Rights Reserved. 1. Create RAID Volume 2. Delete RAID Volume 3. Reset Disks to Non-RAID [ MAIN - Gigabyte H370M D3H GSM | RAID Setup Guide - Page 14
21). Intel(R) Rapid Storage Technology - Option ROM - 16.0.2.3402 Copyright (C) Intel Corporation to update data from the master drive to the recovery drive manually using the Intel® option: On Request: volume is updated manually Continuous: volume is updated automatically [hi]-Change [TAB]- - Gigabyte H370M D3H GSM | RAID Setup Guide - Page 15
® IRST utility. In case you are unable to run the Intel® IRST utility due to an application error or operating system issue, you will need to remove acceleration or manually enable synchronization (Maximized mode only) using this option in the RAID ROM utility. Steps: Select Acceleration Options - Gigabyte H370M D3H GSM | RAID Setup Guide - Page 16
USB thumb drive and then browse to the location of the driver. The location of the driver is as follows: \IRST\f6flpy-x64 Step 4: When a screen as shown in Figure 1 appears, select Intel Chipset SATA RAID Controller and click Next to load the driver and continue the OS installation. Figure 1 - 16 - - Gigabyte H370M D3H GSM | RAID Setup Guide - Page 17
your computer. •• Performing the Rebuild in the Operating System While in the operating system, make sure the chipset driver has been installed from the motherboard driver disk. Then launch the Intel® Rapid Storage Technology utility from the Start menu. Step 1: Go to the Manage menu and click - Gigabyte H370M D3H GSM | RAID Setup Guide - Page 18
Recovery Volume only) When two hard drives are set to Recovery Volume in Update on Request mode, you can restore the master drive data to the last instructions to complete and exit the RAID Configuration Utility. Intel(R) Rapid Storage Technology - Option ROM - 16.0.2.3402 Copyright (C) Intel - Gigabyte H370M D3H GSM | RAID Setup Guide - Page 19
Step 1: After entering the operating system, insert the motherboard driver disk into your optical drive. On the Xpress Install screen, select Intel(R) Optane(TM) Memory System Acceleration (Note) to install. Follow the on-screen instructions to continue. The system will auto-restart. Step 2: After - Gigabyte H370M D3H GSM | RAID Setup Guide - Page 20
to stop functioning correctly. •• If you want to change/remove the Optane™ memory, you must disable it using the Intel® Rapid Storage Technology or Intel(R) Optane Memory application first. •• After enabling the Optane™ memory, the related BIOS settings will remain even after a BIOS update. - 20 -
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
 |
 |
- 1 -
Configuring a RAID Set
Configuring SATA Controllers
........................................................................................
2
Installing the RAID/AHCI Driver and Operating System
.............................................
16
Installing an Intel
®
Optane
™
Memory
...........................................................................
19