Harbor Freight Tools 32046 User Manual
Harbor Freight Tools 32046 - Air Angle Die Grinder Manual
 |
View all Harbor Freight Tools 32046 manuals
Add to My Manuals
Save this manual to your list of manuals |
Harbor Freight Tools 32046 manual content summary:
- Harbor Freight Tools 32046 | User Manual - Page 1
Instructions Visit our website at: http://www.harborfreight.com Read this material before using this product. Failure to do so can result in serious injury. Save this manual . Copyright© 1997, 2009 by Harbor Freight Tools®. All rights reserved. No portion of this manual within this manual may - Harbor Freight Tools 32046 | User Manual - Page 2
for future reference. Safety Alert Symbol and Signal Words In this manual, on the labeling, and all other information provided with this product the risks of electric shock, fire, and injury to persons, read all the instructions before using the tool. Work area a. Keep the work area clean and well - Harbor Freight Tools 32046 | User Manual - Page 3
and care tached to a rotating part of the tool increases the risk of personal injury. a. Use clamps or another practical way to secure and support the e. Do not overreach. Keep proper workpiece to a stable platform. footing and balance at all times. Holding the work by hand or against Proper - Harbor Freight Tools 32046 | User Manual - Page 4
the tool's operation. If damaged, have the Air Angle Die Grinder serviced before using. Many accidents are caused by poorly main- Never use oxygen the tool is damaged. h. Use only accessories that are Save these instructions. identified by the manufacturer for the specific tool model. Use of an - Harbor Freight Tools 32046 | User Manual - Page 5
for the forces gener- ated may break and forcefully launch Specific Safety Instructions pieces. 1. The warnings and precautions dis- 4. Attach all accessories properly to the cussed in this manual cannot cover tool before connecting the air sup- all possible conditions and situations - Harbor Freight Tools 32046 | User Manual - Page 6
a doctor and then have regular medical checkups to ensure medical problems are not being caused or worsened from use. Pregnant women or , maintain tool as explained in this manual. If abnormal vibration occurs, stop immediately. Save these instructions. SKU 32046 For technical questions, please - Harbor Freight Tools 32046 | User Manual - Page 7
the parts listed in the following pages, refer to the Assembly Diagram near the end of this manual. 1. Incorporate an in-line oiler, shut-off valve, regulator with pressure gauge, and filter for best service, as shown in the diagram above. An in-line shutoff valve is an important safety SKU - Harbor Freight Tools 32046 | User Manual - Page 8
. Operating Instructions Read the entire Important Safety Information section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Inspect tool before use, looking for damaged, loose, or missing parts. If any problems - Harbor Freight Tools 32046 | User Manual - Page 9
Specific Operating Instructions 1. If an automatic oiler is not used, add a few drops of Pneumatic Tool Oil inside the air inlet before every use. NOTE: The Die Grinder - Harbor Freight Tools 32046 | User Manual - Page 10
User-Maintenance Instructions Procedures not specifically explained in this manual must be performed only by a qualified damaged equipment. If abnormal noise, vibration, or leaking air occurs, have the problem corrected before further use. To prevent explosion: Lubricate the tool only with specified - Harbor Freight Tools 32046 | User Manual - Page 11
Troubleshooting Problem Decreased tool. Install in-line filter in air supply as stated in manual. 7. Vane wear or damage. 7. Replace all vanes. Housing all safety precautions whenever diagnosing or servicing the tool. Disconnect air supply before service. SKU 32046 For technical questions, - Harbor Freight Tools 32046 | User Manual - Page 12
PLEASE READ THE FOLLOWING CAREFULLY The manufacturer and/or distributor has provided the parts list and assembly diagram in this manual as a reference tool only. Neither the manufacturer or distributor makes any representation or warranty of any kind to the buyer that he or she is - Harbor Freight Tools 32046 | User Manual - Page 13
parts list & assembly DIAGRAM Part Description Qty Part Description Qty 1 Air Inlet 1 18 Rotor 1 2 End Cap 1 19 Vanes 4 3 Housing 1 20 Bushing 1 4 Control Lever 1 21 Front End Plate 1 5 Spring Pin 1 22 Ball Bearing 2 6 Bushing 1 23 Nipple 1 7 Valve 1 24 Bevel Gear 1 - Harbor Freight Tools 32046 | User Manual - Page 14
LIMITED 90 DAY WARRANTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
 |
 |
1/4” AIR ANGLE DIE GRINDER
32046
SET UP AND OPERATING INSTRUCTIONS
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Copyright
©
1997, 2009 by Harbor Freight Tools
®
.
All rights reserved.
No portion of this manual or any
artwork contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally.
Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for as-
sembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
Revised 09i