Home » Harbor Freight Tools Manuals » Tools » Harbor Freight Tools 35098 » Manual Viewer

Harbor Freight Tools 35098 User Manual

Harbor Freight Tools 35098 - 8in. Wet/6in. Dry Grinder Manual

View all Harbor Freight Tools 35098 manuals

Add to My Manuals
Save this manual to your list of manuals

Harbor Freight Tools 35098 manual content summary:

Harbor Freight Tools 35098 | User Manual - Page 1
Instructions Distributed exclusively by Harbor Freight Tools®. 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our website at: http://www.harborfreight.com Read this material before using this product. Failure to do so can result in serious injury. Save this manual within this manual may not
Harbor Freight Tools 35098 | User Manual - Page 2
no number). Keep this manual and the receipt in a safe and dry place for future reference. Important SAFETY Information In this manual, on the labeling, Warnings WARNING Read all safety warnings and instructions. Failure to follow the warnings and instructions may result in electric shock, fire and
Harbor Freight Tools 35098 | User Manual - Page 3
at all times. 13. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories. 14. DISCONNECT TOOLS before servicing; when changing accessories, such as blades, bits, cutters, and the like. 15. REDUCE THE RISK OF
Harbor Freight Tools 35098 | User Manual - Page 4
of the electric cord or plug is necessary, do not connect the equipment-grounding conductor to a live terminal. 4. Check with a qualified electrician or service personnel if the grounding instructions are not completely SKU 35098 For technical questions, please call 1-800-444-3353. Page 4
Harbor Freight Tools 35098 | User Manual - Page 5
Grinder Safety Warnings POSITION OF GRINDER than the rating of the product. Do not use damaged extension cords. Examine extension cord before using and replace if damaged. Do not abuse extension cords and do not yank on any cord to disconnect. Keep cord away from heat and sharp edges. Always
Harbor Freight Tools 35098 | User Manual - Page 6
carbide wheels (not included) for nonferrous metals. 11. When servicing use only identical replacement parts. 12. Only use safety .5, et seq.) 19. The warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur
Harbor Freight Tools 35098 | User Manual - Page 7
ups to ensure medical problems are not being caused or worsened from use. Pregnant women or Information section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Save these instructions. To prevent serious injury from accidental
Harbor Freight Tools 35098 | User Manual - Page 8
3. Avoid water reaching the electrical outlet by arranging the power cord with a "drip loop" as described under the Grinder Safety Warnings section of this manual. 3. Mark the base hole locations on the table surface, then set the Grinder aside. 4. Drill two 1/2" holes in the table surface and bolt
Harbor Freight Tools 35098 | User Manual - Page 9
Grinding Wheels The grinding wheels are preassembled on the grinder. Remove them and perform a Ring Test before first use as described in the following sections, then re-install the Wheels. Replacing Dry Grinding Wheel (59) 1. Remove three Screws (51), Nuts (52) and Toothed Washers (13) from Cover (
Harbor Freight Tools 35098 | User Manual - Page 10
If cracked, there will be a dead sound and not a clear ring. General Operating Instructions Turning the Grinder on and off 1. Check that the Power Switch (42) is other. Allow the wheel to reach full speed. Use the tool rest to support your hand and the dresser, and apply to the wheel evenly to all
Harbor Freight Tools 35098 | User Manual - Page 11
Using the Grinder 5. Flat chisels should be ground in 1. Always bring the workpiece into the Wheel gently and without jarring. the same way as above, with the exception to flattening the tip. The tip should be ground to a mild point 2. When using the Wet Grinding Wheel, periodically check that
Harbor Freight Tools 35098 | User Manual - Page 12
Servicing Procedures not specifically explained in this manual If abnormal noise or vibration occurs, have the problem corrected before further use. 1. Empty the Water water from the Water Reservoir (22) (See General Operating Instructions - Emptying the Water Reservoir). b. To remove the Water
Harbor Freight Tools 35098 | User Manual - Page 13
Troubleshooting Problem Tool will not start. Possible Causes 1. Cord not connected. 2. No power at no other loads. 1. Check that the Wheel is secured in place. 2. Replace Wheel. 3. Have tool serviced by a qualified technician. Tighten Nut (11) to secure Wet Wheel in place, being careful not to
Harbor Freight Tools 35098 | User Manual - Page 14
provided the parts list and assembly diagram in this manual as a reference tool only. Neither the manufacturer Relief 29 Cable with Plug 30 Capacitor Holder 31 Plug-in Wire Lead 33 Wire Case 34 Washer #1 35 Washer Support #1 36 Bushing #1 Parts List Qty 1 1 1 1 1 2 2 1 1 1 1 8 22 2 8 1 1 2
Harbor Freight Tools 35098 | User Manual - Page 15
ASSEMBLY DIAGRAM 65 13 60 67 69 70 68 71 66 66 13 52 39 34 Record Product's Serial Number Here: Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not available individually as
Harbor Freight Tools 35098 | User Manual - Page 16
Limited 1 year / 90 Day warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that for a period of ninety days from date of purchase that the engine/motor, the belts (if so equipped), and