Harbor Freight Tools 37793 User Manual

Harbor Freight Tools 37793 - 2.5 Horsepower Plunge Router Manual

Get Harbor Freight Tools 37793 - 2.5 Horsepower Plunge Router PDF manuals and user guides View all Harbor Freight Tools 37793 manuals
Add to My Manuals
Save this manual to your list of manuals

Harbor Freight Tools 37793 manual content summary:

  • Harbor Freight Tools 37793 | User Manual - Page 1
  • Harbor Freight Tools 37793 | User Manual - Page 2
    injury. Addresses practices not related to personal injury. IMPORTANT SAFETy INFORMATION General Power Tool Safety Warnings Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and
  • Harbor Freight Tools 37793 | User Manual - Page 3
    SAFETy SETUP Electrical Safety 1. Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with grounded power tools. Unmodified plugs and matching outlets will reduce risk of electric shock. 2. Avoid body contact with grounded surfaces such as pipes,
  • Harbor Freight Tools 37793 | User Manual - Page 4
    persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools a hazardous situation. Service Have your power tool serviced by a qualified repair 2. Use clamps or another practical way to secure and support the workpiece to a stable platform. Holding the work by
  • Harbor Freight Tools 37793 | User Manual - Page 5
    et seq.) 15. The warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may a doctor and then have regular medical check-ups to ensure medical problems are not being caused or worsened from use. Pregnant women or people
  • Harbor Freight Tools 37793 | User Manual - Page 6
    the grounding prong from the plug. Do not use the tool if the power cord or plug is damaged. If damaged, have it repaired by a service facility before use. If the plug will not fit the outlet, have a proper outlet installed by a qualified electrician. Grounded Tools: Tools with Three Prong Plugs
  • Harbor Freight Tools 37793 | User Manual - Page 7
    . No Load Revolutions per Minute (RPM) WARNING marking concerning Risk of Eye Injury. Wear ANSI-approved safety goggles with side shields. Read the manual before set-up and/or use. WARNING marking concerning Risk of Fire. Do not cover ventilation ducts. Keep flammable objects away. WARNING marking
  • Harbor Freight Tools 37793 | User Manual - Page 8
    inch 2-1/2 inches; 3 adjustable plunge settings 224184 Setup - Before Use: Read the ENTIRE IMPORTANT SAFETy INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Note: For additional information regarding the parts
  • Harbor Freight Tools 37793 | User Manual - Page 9
    SAFETy SETUP Operating Instructions Read the ENTIRE IMPORTANT SAFETy INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Tool Set Up TO PREVENT SERIOUS INJURy FROM AccIDENTAL OPERATION: Make
  • Harbor Freight Tools 37793 | User Manual - Page 10
    (26). 3. Loosen the Plunge Lock Lever. Using the Straight Guide The Straight Guide (4A) and Guide Holder (6A) are used for chamfering or grooving cuts. 1. Place the Straight Guide on the Guide Holder with the Wing Nut (B). 2. Insert Guide Holder into the holes in the router base. 3. Adjust the
  • Harbor Freight Tools 37793 | User Manual - Page 11
    2. Loosen the screws on the router base. 3. Insert the Template Guide and retighten screws. Screw Note: The cut size may be slightly different nails and screws before working. Do not cut nails or screws. General Operating Instructions 1. Verify Plunge Lock Lever (26) is loose. 2. Make sure that
  • Harbor Freight Tools 37793 | User Manual - Page 12
    Chip Deflector (53), replace immediately. 4. For bit changing instructions see Tool Set Up on page 9. 5. WARNING! If the supply cord of this power tool is damaged, it must be replaced only by a qualified service technician. Problem Tool will not start. Tool operates slowly. Performance decreases
  • Harbor Freight Tools 37793 | User Manual - Page 13
    AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY Guide; Dimensions: A = 37/64″, B = 5/8″, C = 33/64″ 1 2A Collet Sleeve 1 3A Trimmer Guide 1 4A Straight Guide 1 5A Wrench 1 6A Guide
  • Harbor Freight Tools 37793 | User Manual - Page 14
    SAFETy SETUP Parts List Part 1 2 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 Description Pan Head Screw M5x20 w/washer Rear Cover Motor Housing Name Plate Field Baffle Plate Ball Bearing 629-2RS (GB/1276-94) Insulation Washer Armature Assembly w/
  • Harbor Freight Tools 37793 | User Manual - Page 15
    Assembly Diagram SAFETy SETUP OPERATION MAINTENANcE Item 37793 For technical questions, please call 1-888-866-5797. Page 15
  • Harbor Freight Tools 37793 | User Manual - Page 16
    Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16