Harbor Freight Tools 38142 User Manual

Harbor Freight Tools 38142 - 13 in. Bench Mount Drill Press Manual

Get Harbor Freight Tools 38142 - 13 in. Bench Mount Drill Press PDF manuals and user guides View all Harbor Freight Tools 38142 manuals
Add to My Manuals
Save this manual to your list of manuals

Harbor Freight Tools 38142 manual content summary:

  • Harbor Freight Tools 38142 | User Manual - Page 1
  • Harbor Freight Tools 38142 | User Manual - Page 2
    moderate injury. Addresses practices not related to personal injury. IMPORTANT SAFETY INFORMATION General Tool Safety Warnings Read all safety warnings and instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and
  • Harbor Freight Tools 38142 | User Manual - Page 3
    at all times. 14. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories. 15. DISCONNECT TOOLS before servicing; when changing accessories, such as blades, bits, cutters, and the like. 16. REDUCE THE RISK OF
  • Harbor Freight Tools 38142 | User Manual - Page 4
    different outlet. Drill Press Safety Warnings For Your Own Safety Read Instruction Manual Before Operating Drill Press 1. Wear eye protection. 2. Do not wear may result in a risk of injury to persons. 8. When servicing use only identical replacement parts. 9. Do not depress the spindle lock
  • Harbor Freight Tools 38142 | User Manual - Page 5
    et seq.) 18. The warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may a doctor and then have regular medical check‑ups to ensure medical problems are not being caused or worsened from use. Pregnant women or people
  • Harbor Freight Tools 38142 | User Manual - Page 6
    in this section. Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram near the end of this manual. Mounting Secure the tool to a supporting structure before use. Before assembly, bolt the Base to a flat, level, solid workbench capable of
  • Harbor Freight Tools 38142 | User Manual - Page 7
    SAFETY SETUP Table and Support Arm to Column 1. Remove the Rack (2B) from the Column (1B) by rack is uppermost. The bottom end of the rack will be located in the groove formed by the column support and the column. 4. Hold the machine in this position while replacing the collar on the column, and
  • Harbor Freight Tools 38142 | User Manual - Page 8
    its mounting between the motor and spindle pulleys. Functions 3. Consult the chart inside the pulley cover (or the Drill Speed chart in this manual), and install the belts in the positions corresponding to spindle/drill speed required. 4. Turn the Belt Tension Lever (19A) counterclockwise so that
  • Harbor Freight Tools 38142 | User Manual - Page 9
    SAFETY SETUP Operating Instructions Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Tool Set Up TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Turn
  • Harbor Freight Tools 38142 | User Manual - Page 10
    SAFETY Changing Drill Speed Before changing the speeds, make sure the machine is switched OFF and UNPLUGGED. 1. Open the pulley cover. 2. Slacken off the Belt Tension Lock Knobs (18A) on both sides of the head and turn the Belt Tension Lever (19A) clockwise, to bring the Motor Pulley (11A) closer
  • Harbor Freight Tools 38142 | User Manual - Page 11
    - or align the table so that the hole in its center is in line with the drill bit. Figure D: Bracing workpiece against column General Operating Instructions 1. Bring the drill bit down with the Feed Knob to where the hole is to be drilled. Make minor workpiece alignment adjustments. 2. Plug the
  • Harbor Freight Tools 38142 | User Manual - Page 12
    Servicing Procedures not specifically explained in this manual vibration occurs, have the problem corrected before further use service technician. Belt Inspection and Tensioning 1. Examine belt for cracks, tears in the backing, and other damage. 2. Replace belt if damaged, following the instructions
  • Harbor Freight Tools 38142 | User Manual - Page 13
    SAFETY Troubleshooting Problem Possible Causes Likely Solutions Tool will not start. 1. Cord not connected. 1. before service. SETUP OPERATION MAINTENANCE PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL
  • Harbor Freight Tools 38142 | User Manual - Page 14
    SAFETY Parts Lists and Diagrams Pulley and Spindle Parts List and Diagram Part # 1 2 3 4 5 6 7 8 9 10 11 12 13 Description "V" Belt M24 Pulley Nut Spindle Pulley Pulley Insert Ball Bearing Spacer Retaining Ring Retaining Ring Ball Bearing Quill Gasket Quill Ball Bearing Spindle Shaft Code
  • Harbor Freight Tools 38142 | User Manual - Page 15
    15A 16A 17A 18A 19A 20A 21A 22A 23A Description Head w/pointer and trim Cable Clamp Pan Head Screw Hex. Screw Adjusting Lever Motor Support Bracket Motor Support Bracket Motor Mount Lockwasher Nut Hex. Motor Pulley Skt. Screw Set Motor Hex. Nut Washer Motor Cable Hex Screw Belt Tension Lock Knob
  • Harbor Freight Tools 38142 | User Manual - Page 16
    4B 5B 6B 7B 8B 11B 12B 13B 14B 15B 16B 17B 18B 19B 19A Description Column Rack Hex. Socket Screw Set Column Support Hex. Head Screw Base Table Support w/indicator Crank Skt. Screw Set M6 Bevel Table Lock Screw Table Clamp Arm w/ scale Table Arm Locking Handle Helical Gear Worm Collar
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16