Home » Harbor Freight Tools Manuals » Tools » Harbor Freight Tools 39797 » Manual Viewer

Harbor Freight Tools 39797 User Manual

Harbor Freight Tools 39797 - 6in. Bench Grinder Manual

View all Harbor Freight Tools 39797 manuals

Add to My Manuals
Save this manual to your list of manuals

Harbor Freight Tools 39797 manual content summary:

Harbor Freight Tools 39797 | User Manual - Page 1
INSTRUCTIONS Distributed exclusively by Harbor Freight Tools®. 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our website at: http://www.harborfreight.com Read this material before using this product. Failure to do so can result in serious injury. SAVE THIS MANUAL within this manual may not
Harbor Freight Tools 39797 | User Manual - Page 2
11 WORK PIECE AND WORK AREA SET UP 11 GENERAL OPERATING INSTRUCTIONS 11 MAINTENANCE AND SERVICING 12 SPECIFICATIONS 8 CLEANING, MAINTENANCE, AND LUBRICATION 12 ALL MODELS 8 TROUBLESHOOTING 13 MODEL 37822 8 PARTS LIST 14 MODEL 37823 8 MODEL 39797 8 ASSEMBLY DIAGRAM 15 MODEL
Harbor Freight Tools 39797 | User Manual - Page 3
injury. General Tool Safety Warnings IMPORTANT SAFETY INFORMATION In this manual, on the labeling, and all other information provided with this instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions
Harbor Freight Tools 39797 | User Manual - Page 4
at all times. 13. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories. 14. DISCONNECT TOOLS before servicing; when changing accessories, such as blades, bits, cutters, and the like. 15. REDUCE THE RISK OF
Harbor Freight Tools 39797 | User Manual - Page 5
5. AND DEATH FROM INCORRECT GROUNDING WIRE CONNECTION READ AND FOLLOW THESE 6. INSTRUCTIONS: equipment-grounding conductor to a live terminal. Check with a qualified electrician or service personnel if the grounding instructions are not completely understood, or if in doubt as to whether the
Harbor Freight Tools 39797 | User Manual - Page 6
Safety Warnings For Your Own Safety Read Instruction Manual Before Operating Grinder adequate protection. Eye protection by the manufacturer may result in a risk of injury to persons. 13. When servicing use only identical replacement parts. 14. Only use safety equipment that has been approved
Harbor Freight Tools 39797 | User Manual - Page 7
4. 21. The warnings, precautions, and in- structions discussed in this instruction manual cannot cover all possible con- 5. ditions and situations that may occur a doctor and then have regular medical checkups to ensure medical problems are not being caused or worsened from use. Pregnant women or
Harbor Freight Tools 39797 | User Manual - Page 8
SPECIFICATIONS All Models 180264 Motor No Load Speed 3450 RPM Arbor Size 5/8" with 1/2" Adapter Base Size 5" x 7" Mounting Holes 2 x 3/8" Work Light Bulb 40 W Household type UNPACKING When unpacking, make sure that the item is intact and undamaged. If any parts are missing or broken,
Harbor Freight Tools 39797 | User Manual - Page 9
INSTRUCTIONS FOR PUTTING INTO USE Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all in the following pages, refer to the Assembly Diagram near the end of this manual. Assembly 1. Installing Tool Rests a. Turn the Grinder off and unplug it. FIGURE
Harbor Freight Tools 39797 | User Manual - Page 10
3. Installing Bracket to Eye Shield - FIGURE 3 a. Select one flat bracket and one eye shield. Assemble as shown in Figure 3. b. Repeat for left eye shield. 4. Installing Eye Shield to Grinder a. For installation of the right eye shield (19), make sure that the holes in the eye shield bracket face
Harbor Freight Tools 39797 | User Manual - Page 11
OPERATING INSTRUCTIONS Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under utility lines, nearby that will present a hazard while working. General Operating Instructions TO PREVENT SERIOUS INJURY: 5. DO NOT OPERATE WITH ANY GUARD DISABLED
Harbor Freight Tools 39797 | User Manual - Page 12
it must TO PREVENT SERIOUS INJURY FROM TOOL be replaced only by a qualified service technician. FAILURE: Do not use damaged equipment. If abnormal noise or vibration occurs, have the problem corrected before further use. Cleaning, Maintenance, and Lubrication 1. BEFORE EACH USE, inspect the
Harbor Freight Tools 39797 | User Manual - Page 13
Troubleshooting Problem Possible Causes Tool will not start. 1. Cord not connected. Likely cool. Press reset button on tool. 4. Internal damage or wear. (Carbon 4. Have technician service tool. brushes or switch, for example.) Tool operates Power being reduced by long or Eliminate use
Harbor Freight Tools 39797 | User Manual - Page 14
PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
Harbor Freight Tools 39797 | User Manual - Page 15
ASSEMBLY DIAGRAM 4b 4a 38 39 40 4b 4a Record Product's Serial Number Here: Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not avail- able individually as replacement parts. REV 01k
Harbor Freight Tools 39797 | User Manual - Page 16
90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This