Harbor Freight Tools 60238 User Manual
Harbor Freight Tools 60238 - 8 in. Bench Mount Drill Press Manual
 |
View all Harbor Freight Tools 60238 manuals
Add to My Manuals
Save this manual to your list of manuals |
Harbor Freight Tools 60238 manual content summary:
- Harbor Freight Tools 60238 | User Manual - Page 1
Manual & Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product's serial number in the back of the manual Tools required for assembly and service may not be included. Read - Harbor Freight Tools 60238 | User Manual - Page 2
moderate injury. Addresses practices not related to personal injury. IMPORTANT SAFETY INFORMATION General Tool Safety Warnings Read all safety warnings and instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and - Harbor Freight Tools 60238 | User Manual - Page 3
at all times. 14. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories. 15. DISCONNECT TOOLS before servicing; when changing accessories, such as blades, bits, cutters, and the like. 16. REDUCE THE RISK OF - Harbor Freight Tools 60238 | User Manual - Page 4
to a different outlet. Drill Press Safety Warnings For Your Own Safety Read Instruction Manual Before Operating Drill Press 1. Wear eye protection. 2. Do not wear may result in a risk of injury to persons. 8. When servicing use only identical replacement parts. 9. Only use safety equipment that - Harbor Freight Tools 60238 | User Manual - Page 5
et seq.) 18. The warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may a doctor and then have regular medical check‑ups to ensure medical problems are not being caused or worsened from use. Pregnant women or people - Harbor Freight Tools 60238 | User Manual - Page 6
in this section. Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram near the end of this manual. Mounting Secure the tool to a supporting structure before use. Before assembly, bolt the Base to a flat, level, solid workbench capable of - Harbor Freight Tools 60238 | User Manual - Page 7
clean, dry and burr free, place the Chuck with its open jaws on the scrap wood, directly under the Spindle. Figure B: Installing Table Support Headstock (42) Set Screws (9) Feed Handle (6) Feed Seat (7) Figure C: Installing Headstock and Feed Handles 5. Use the Feed Handles (6) to gently lower the - Harbor Freight Tools 60238 | User Manual - Page 8
SAFETY SETUP Operating Instructions Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under movement, tighten Angle Bolt (56) and Pivot Lever (51) after adjustment. Table Support (52) Column (8) Angle Bolt (56) under Table Pivot Lever (51) - Harbor Freight Tools 60238 | User Manual - Page 9
SAFETY SETUP Changing Drill Speed Before changing the speeds, make sure the machine is switched OFF and UNPLUGGED. 1. Open the pulley cover. 2. Loosen the Motor Tension Knob (10) on the Headstock (42), and move the Motor (14) towards the Headstock to relieve tension on the Belt (59). Lamp (34) 3. - Harbor Freight Tools 60238 | User Manual - Page 10
SAFETY Workpiece and Work Area Set Up 1. Designate a work area that is clean and well‑lit. The work area must not allow access by children or pets to prevent distraction and injury. 2. Route the power cord along a safe route to reach the work area without creating a tripping hazard or exposing the - Harbor Freight Tools 60238 | User Manual - Page 11
General Operating Instructions 1. Bring the drill bit down with the Feed Knob to where the hole is to be drilled. Make minor workpiece alignment adjustments. 2. Plug the Power - Harbor Freight Tools 60238 | User Manual - Page 12
Servicing Procedures not specifically explained in this manual . If abnormal noise or vibration occurs, have the problem corrected before further use. Cleaning, Maintenance, and Lubrication . 2. Replace belt if damaged, following the instructions under Changing Drill Speed on page 9. SETUP - Harbor Freight Tools 60238 | User Manual - Page 13
SAFETY Troubleshooting Problem Possible Causes Likely Solutions Tool will not start. 1. Cord not connected. . 1. Internal damage or wear. (Carbon brushes or bearings, for example.) 4. Have technician service tool. Eliminate use of extension cord. If an extension cord is needed, use one with the - Harbor Freight Tools 60238 | User Manual - Page 14
/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY .9×10 48 Switch 49 Nut M8 50 Set Screw 51 Pivot Lever 52 Table Support 53 Angle Scale 54 Table 55 Spring Washer 12 56 Angle Bolt M12×25 - Harbor Freight Tools 60238 | User Manual - Page 15
SAFETY SETUP Assembly Diagram 30 29 28 31 27 26 25 24 59 34 33 33 32 23 15 22 60 21 16 61 57 38 35 20 62 39 39 19 63 64 39 73 39 40 27 36 37 17 18 3 15 58 41 64 63 24 48 47 46 45 44 43 42 13 14 49 11 12 10 50 9 8 65 66 67 56 55 54 53 52 51 7 6 68 5 66 - Harbor Freight Tools 60238 | User Manual - Page 16
Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
 |
 |
Visit our website at: http://www.harborfreight.com
Email our technical support at: [email protected]
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Copyright
©
2012 by Harbor Freight Tools
®
.
All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally.
Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
When unpacking, make sure that the product is intact
and undamaged.
If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
Save This Manual
Keep this manual for the safety warnings and precautions, assembly, operating,
inspection, maintenance and cleaning procedures.
Write the product’s serial number in the back of the manual
near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and
the receipt in a safe and dry place for future reference.
Owner’s Manual & Safety Instructions
REV 14i