Harbor Freight Tools 60241 User Manual

Harbor Freight Tools 60241 - 23 Gauge Pin Nailer Manual

Get Harbor Freight Tools 60241 - 23 Gauge Pin Nailer PDF manuals and user guides View all Harbor Freight Tools 60241 manuals
Add to My Manuals
Save this manual to your list of manuals

Harbor Freight Tools 60241 manual content summary:

  • Harbor Freight Tools 60241 | User Manual - Page 1
  • Harbor Freight Tools 60241 | User Manual - Page 2
    with side shields. Symbol Property or statement Warning marking concerning Risk of Puncture Injury. Wear heavy‑duty work gloves. Read the manual before set-up and/or use. WARNING marking concerning Risk of Hearing Loss. Wear hearing protection. WARNING marking concerning Risk of Respiratory
  • Harbor Freight Tools 60241 | User Manual - Page 3
    should always be followed, including the following: General To reduce the risks of electric shock, fire, and injury to persons, read all the instructions before using the tool. Work area a. Keep the work area clean and well lighted. Cluttered benches and dark areas increase the risks of electric
  • Harbor Freight Tools 60241 | User Manual - Page 4
    way to secure and support the workpiece to 's operation. If damaged, have the tool serviced before using. Many accidents are caused by fasteners listed in the Specifications chart of this manual. Fasteners not identified for use with this tool INSTRUCTIONS. Operation Maintenance Page 4 For technical questions,
  • Harbor Freight Tools 60241 | User Manual - Page 5
    or anyone whether it contains fasteners or not. 21. Obey the manual for the air compressor used to power this tool. 5. Do not make any modifications to this tool. 13. Refer to the tool maintenance instructions for detailed information on the proper maintenance of the tool. 14. Fire fasteners
  • Harbor Freight Tools 60241 | User Manual - Page 6
    a doctor and then have regular medical check-ups to ensure medical problems are not being caused or worsened from use. Pregnant women or , maintain tool as explained in this manual. If abnormal vibration occurs, stop immediately. SAVE THESE INSTRUCTIONS. Setup Operation Maintenance Page 6 For
  • Harbor Freight Tools 60241 | User Manual - Page 7
    Functional Description Specifications Maximum Air Pressure Air Inlet Air Consumption Nail Type 100 PSI 1/4″ - 18 NPT 0.2 CFM @ 90 PSI 23 gauge, 1/2″-7/8″ long Safety Setup Operation Maintenance Item 60241 For technical questions, please call 1-800-444-3353. Page 7
  • Harbor Freight Tools 60241 | User Manual - Page 8
    Safety Setup Components and Controls Safety Lock Trigger Air Inlet Plug Magazine Lock (located at rear) Drive Guide Magazine Figure A: Components and Controls Operation Maintenance Page 8 For technical questions, please call 1-800-444-3353. Item 60241
  • Harbor Freight Tools 60241 | User Manual - Page 9
    following pages, refer to the Assembly Diagram near the end of this manual. Air Supply TO PREVENT EXPLOSION: Use only clean, dry, regulated, regulator with pressure gauge, oiler, in-line shutoff valve, and quick coupler for best service, as shown on Figure B on page 10 and Figure C on page 11. An
  • Harbor Freight Tools 60241 | User Manual - Page 10
    Safety Setup Operation Maintenance Page 10 Figure B: Portable Air Supply Setup Lubricated Tools BC D A E F A For technical questions, please call 1-800-444-3353. Non-lubricated Tools B Description A Air Hose B Filter C Regulator D Lubricator (optional) E Coupler and Plug F Leader Hose (
  • Harbor Freight Tools 60241 | User Manual - Page 11
    Figure C: Stationary Air Supply Setup Item 60241 For technical questions, please call 1-800-444-3353. Slope Lubricated G Tools C J K H L M F CD E I IN B A B A F C J F Non-lubricated Tools LO H Description A Vibration Pads B Anchor Bolts C Ball Valve D Isolation Hose E Main Air
  • Harbor Freight Tools 60241 | User Manual - Page 12
    Setup Operating Instructions Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Inspect tool before use, looking for damaged, loose, and missing parts. If any problems are found
  • Harbor Freight Tools 60241 | User Manual - Page 13
    Safety General Operating Instructions 1. Before each use, test the tool as directed in the prior fastener location and place the Drive Guide fully against the workpiece. 4. Squeeze the Trigger to fire a fastener. Note: Always make sure the Drive Guide is flush against the workpiece during use
  • Harbor Freight Tools 60241 | User Manual - Page 14
    Instructions Procedures not specifically explained in this manual Empty the Magazine and leave the Magazine Cover pulled back during service. The Magazine is spring‑loaded and may cause parts or a or leaking air is detected, have the problem corrected before further use. TO PREVENT EXPLOSION:
  • Harbor Freight Tools 60241 | User Manual - Page 15
    place. 8. If the jam cannot be cleared using the methods above, have the tool serviced by a qualified technician. Magazine Lock (located at rear) Cover Drive Plate Guide Magazine Magazine Cover Figure E: Clearing Jams Operation Maintenance Item 60241 For technical questions, please call
  • Harbor Freight Tools 60241 | User Manual - Page 16
    Troubleshooting Problem Insufficient pressure (PSI). 1. Clear jammed fastener according to Clearing Jams instructions. 2. Reload with correct fasteners. 3. Empty, then reload precautions whenever diagnosing or servicing the tool. Disconnect air supply before service. Operation Maintenance Page
  • Harbor Freight Tools 60241 | User Manual - Page 17
    PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
  • Harbor Freight Tools 60241 | User Manual - Page 18
    52 53 54 55 56 57 58 59 Description Screw Screw Cover Plate Drive Guide Pin (1.5x10) Feeder Shoe Spring Pin (2x10) Rail Magazine Cover Spring Pin Spring Spring Stop Plate Screw Pin Spring Magazine Magazine Lock Washer Spring Washer Support Nut Rubber Grip O-Ring (40.2x2.3) End Cap Air Inlet Plug
  • Harbor Freight Tools 60241 | User Manual - Page 19
    Assembly Diagram Safety Setup Operation Maintenance Item 60241 For technical questions, please call 1-800-444-3353. Page 19
  • Harbor Freight Tools 60241 | User Manual - Page 20
    Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20