Harbor Freight Tools 60363 User Manual

Harbor Freight Tools 60363 - 6.5 HP OHV Horizontal Shaft Gas Engine EPA Manual

Get Harbor Freight Tools 60363 - 6.5 HP OHV Horizontal Shaft Gas Engine EPA PDF manuals and user guides View all Harbor Freight Tools 60363 manuals
Add to My Manuals
Save this manual to your list of manuals

Harbor Freight Tools 60363 manual content summary:

  • Harbor Freight Tools 60363 | User Manual - Page 1
  • Harbor Freight Tools 60363 | User Manual - Page 2
    SAFETY SETUp Table of Contents Specifications 2 Safety 3 Setup 6 Operation 7 Maintenance 10 Troubleshooting 14 Warranties 19 Parts List and Diagram 16 Specifications Displacement 212cc Engine Type Horizontal Single Cylinder 4 stroke OHV Meets EPA phase III emissions standards
  • Harbor Freight Tools 60363 | User Manual - Page 3
    . Failure to follow all instructions listed below may result in fire, serious injury and/or DEATH. The warnings and precautions discussed in this manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are
  • Harbor Freight Tools 60363 | User Manual - Page 4
    goggles, heavy-duty work gloves, and dust mask/respirator during set up. 6. Use only lubricants and fuel recommended in the Specifications chart of this manual. 10. Do not leave the equipment unattended when it is running. Turn off the equipment (and remove safety keys, if available) before leaving
  • Harbor Freight Tools 60363 | User Manual - Page 5
    23. Use the equipment, accessories, etc., in accordance with these instructions and in the manner intended for the particular type of equipment, taking equipment is maintained. Do not attempt any service or maintenance procedures not explained in this manual or any procedures that you are uncertain
  • Harbor Freight Tools 60363 | User Manual - Page 6
    for this Engine is warranted for standards set by the U.S. Environmental Protection Agency. For warranty information, refer to the last pages of this manual. WARNING! DO NOT INSTALL THIS ENGINE ON A VEHICLE. NOT FOR HIGHWAY USE. FOLLOW ALL AppLICABLE LAWS FOR INSTALLATION AND USE. Engine Controls
  • Harbor Freight Tools 60363 | User Manual - Page 7
    manual including all text under subheadings therein before set up or use of this product. pre-Start Checks Inspect engine and equipment looking for damaged, loose, and missing parts before set up and starting. If any problems chart on page 11 in the Service section shows other viscosities to use
  • Harbor Freight Tools 60363 | User Manual - Page 8
    SAFETY SETUp Starting the Engine Before Starting the Engine Before starting the engine: a. Follow the Set Up Instructions in the equipment manual to prepare the equipment. b. Inspect the equipment and engine. c. Fill the engine with the proper amount and type of both fuel and oil. d. Read the
  • Harbor Freight Tools 60363 | User Manual - Page 9
    . After this period: • Change the engine oil. Under normal operating conditions subsequent maintenance follows the schedule explained in the MAINTENANCE AND SERVICING section. Stopping the Engine OFF O I 1. To stop the engine in an emergency, turn the Engine Switch off. OpERATION MAINTENANCE
  • Harbor Freight Tools 60363 | User Manual - Page 10
    not use damaged equipment. If abnormal noise, vibration, or excess smoking occurs, have the problem corrected before further use. Follow all service instructions in this manual. The engine may fail critically if not serviced properly. Many maintenance procedures, including any not detailed in this
  • Harbor Freight Tools 60363 | User Manual - Page 11
    SAFETY SETUp Checking and Filling Fuel WARNING! TO pREVENT SERIOUS INJURY FROM FIRE: Fill the fuel tank in a well-ventilated area away from ignition sources. If the engine is hot from use, shut the engine off and wait for it to cool before adding fuel. Do not smoke. 1. Clean the Fuel Cap and the
  • Harbor Freight Tools 60363 | User Manual - Page 12
    SAFETY SETUp Air Filter Element Maintenance 1. Remove the air filter cover and the air filter elements and check for dirt. Clean or replace as described below. 2. Cleaning: • For "paper" filter elements: To prevent injury from dust and debris, wear ANSI-approved safety goggles, NIOSH-approved dust
  • Harbor Freight Tools 60363 | User Manual - Page 13
    SAFETY Storage When the equipment is to remain idle for longer than 20 days, prepare the engine for storage as follows: 1. CLEANING: Wait for engine to cool, then clean engine with dry cloth. NOTICE: Do not clean using water. The water will gradually enter the engine and cause rust damage. Apply a
  • Harbor Freight Tools 60363 | User Manual - Page 14
    SAFETY SETUp Troubleshooting problem Engine will not start possible Causes probable Solutions FUEL diagnose/ repair ignition system. Follow all safety precautions whenever diagnosing or servicing the equipment or engine. OpERATION MAINTENANCE Page 14 For technical questions, please
  • Harbor Freight Tools 60363 | User Manual - Page 15
    spark timing, deposit buildup, worn engine, or other mechanical problems. 1. Impure or low quality gasoline. 2. Engine too etc.). 2. Do not exceed equipment's load rating. 3. Have qualified technician diagnose and service engine. 1. Fill fuel tank with fresh 87+ octane unleaded gasoline. Do not use
  • Harbor Freight Tools 60363 | User Manual - Page 16
    SAFETY pLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
  • Harbor Freight Tools 60363 | User Manual - Page 17
    MAINTENANCE OpERATION SETUp SAFETY Page 17 For technical questions, please call 1-800-520-0882. Assembly Diagram Record product's Serial Number Here: Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration
  • Harbor Freight Tools 60363 | User Manual - Page 18
    Mounting Diagrams Note: Diagrams not to scale. SAFETY SETUp OpERATION MAINTENANCE Page 18 For technical questions, please call 1-800-520-0882. ITEM 60363
  • Harbor Freight Tools 60363 | User Manual - Page 19
    a HFT warranty station as soon as a problem exists. Contact the HFT Customer Service department at the number below to make shipping damaged due to failure to follow the maintenance and operating instructions set forth in the Owner's Manual including, but not limited to: a) Use of parts
  • Harbor Freight Tools 60363 | User Manual - Page 20
    Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20