Harbor Freight Tools 60500 User Manual

Harbor Freight Tools 60500 - 9 in. Bench Top Band Saw Manual

Get Harbor Freight Tools 60500 - 9 in. Bench Top Band Saw PDF manuals and user guides View all Harbor Freight Tools 60500 manuals
Add to My Manuals
Save this manual to your list of manuals

Harbor Freight Tools 60500 manual content summary:

  • Harbor Freight Tools 60500 | User Manual - Page 1
  • Harbor Freight Tools 60500 | User Manual - Page 2
    moderate injury. Addresses practices not related to personal injury. IMPORTANT SAFETY INFORMATION General Tool Safety Warnings Read all safety warnings and instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and
  • Harbor Freight Tools 60500 | User Manual - Page 3
    at all times. 14. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories. 15. DISCONNECT TOOLS before servicing; when changing accessories, such as blades, bits, cutters, and the like. 16. REDUCE THE RISK OF
  • Harbor Freight Tools 60500 | User Manual - Page 4
    qualified electrician or service personnel if the grounding instructions are not completely Safety Warnings For Your Own Safety Read Instruction Manual Before Operating Saw 7. DO NOT OPERATE 3. Maintain proper adjustment of blade tension, blade guides, and thrust bearings. 10. Hot motor!
  • Harbor Freight Tools 60500 | User Manual - Page 5
    et seq.) 21. The warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may a doctor and then have regular medical check‑ups to ensure medical problems are not being caused or worsened from use. Pregnant women or people
  • Harbor Freight Tools 60500 | User Manual - Page 6
    this section. Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram near the end of this manual. Mounting 1. This tool must be mounted to a level, stable bench or table before use. 2. If the mounting surface does not have predrilled holes
  • Harbor Freight Tools 60500 | User Manual - Page 7
    Safety Assembly 1. Unpack the Table (8) and remove the protective cover. 2. Slide the slot in the Table (8) around the Blade. Position the Table (8) onto the Saw over the two posts. Then, pull out and release the Tilt Knob (19) to help align the Table. Connect Tilt Lock (12) here Tilt Knob (19)
  • Harbor Freight Tools 60500 | User Manual - Page 8
    Safety b. b. How the adjustments should be made. Operating Instructions Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Tool Set Up TO PREVENT SERIOUS INJURY FROM ACCIDENTAL
  • Harbor Freight Tools 60500 | User Manual - Page 9
    deflect slightly with finger pressure when tensioned properly. Close the Upper Wheel Cover. 10. Close the Upper Wheel Cover (95). Blade Guide Alignment 11. The Blade Guides (37) support the saw blade at the rear and sides. They prevent twisting and help to keep the blade from being deflected by the
  • Harbor Freight Tools 60500 | User Manual - Page 10
    supported properly. 4. There must not be objects, such as utility lines, nearby that will present a hazard while working. General Operating Instructions c. Bevel cuts are when the saw Table (8) is tilted and proper work guide methods are used. Unlock the Table (8) by loosening the Lock Screw (12)
  • Harbor Freight Tools 60500 | User Manual - Page 11
    Safety Maintenance and Servicing Procedures not specifically explained in this manual must be performed only by a Do not use damaged equipment. If abnormal noise or vibration occurs, have the problem corrected before further use. Cleaning, Maintenance, and Lubrication 1. BEFORE EACH USE, inspect
  • Harbor Freight Tools 60500 | User Manual - Page 12
    the Upper and Lower Wheels (56, 82). 6. Slip new blade through Table Blade Insert (7) and over Upper and Lower Wheels. Slide new blade between Blade Guide and Guide Block (37 & 45). 7. Turn the Blade Release Lever (27) up to the engaged position. 8. Close Upper and Lower Wheel Covers (95, 102) and
  • Harbor Freight Tools 60500 | User Manual - Page 13
    Troubleshooting Problem allow to cool. Press reset button on tool. 4. Have technician service tool. Eliminate use of extension cord. If an extension cord is Saw Blade with a finer pitch. 2. Adjust the Guides/Guards as noted on page 13 & 14 of this manual. 3. Replace the Saw Blade. 1. Slow down the
  • Harbor Freight Tools 60500 | User Manual - Page 14
    Cover 1 102.1 Gasket 1 103 Hinge 4 104 Flat Head Screw & Nut 8 105 Screw 8 106 Small Wheel 1 106.1 Set Screw 1 107 Guide Adjustment Seat 1 107.1 Washer 1 108 Guide Height Knob 1 109 Bolt 2 110 Square Cover 1 111 Band Saw Blade 1 112 Hex-Nut 1 113 Bolt 1 114 Screw 1 116
  • Harbor Freight Tools 60500 | User Manual - Page 15
    Assembly Diagram Safety Setup Operation Maintenance Item 60500 For technical questions, please call 1-800-444-3353. Page 15
  • Harbor Freight Tools 60500 | User Manual - Page 16
    Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16