Harbor Freight Tools 61487 User Manual

Harbor Freight Tools 61487 - 17 in. Floor Mount Drill Press Manual

Get Harbor Freight Tools 61487 - 17 in. Floor Mount Drill Press PDF manuals and user guides View all Harbor Freight Tools 61487 manuals
Add to My Manuals
Save this manual to your list of manuals

Harbor Freight Tools 61487 manual content summary:

  • Harbor Freight Tools 61487 | User Manual - Page 1
  • Harbor Freight Tools 61487 | User Manual - Page 2
    SAFETy Table of contents Safety 3 Specifications 6 Setup 6 Operation 11 Maintenance 15 Parts List and Diagram 18 Warranty 20 WARNING SyMBOLS AND DEFINITIONS This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow
  • Harbor Freight Tools 61487 | User Manual - Page 3
    for best and safest performance. Follow instructions for lubricating and changing accessories. 15. DISCONNECT TOOLS before servicing; when changing accessories, such as hair. 17. USE RECOMMENDED ACCESSORIES. Consult the owner's manual for recommended accessories. The use of improper accessories may
  • Harbor Freight Tools 61487 | User Manual - Page 4
    to a different outlet. Drill press Safety Warnings For your Own Safety Read Instruction Manual Before Operating Drill press 1. Wear eye protection. 2. Do not wear may result in a risk of injury to persons. 8. When servicing use only identical replacement parts. 9. Only use safety equipment that
  • Harbor Freight Tools 61487 | User Manual - Page 5
    et seq.) 17. The warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may a doctor and then have regular medical check-ups to ensure medical problems are not being caused or worsened from use. Pregnant women or people
  • Harbor Freight Tools 61487 | User Manual - Page 6
    parts listed in the following pages, refer to the Assembly Diagram near the end of this manual. Mounting Before assembling and using the Drill Press, secure the Base to a supporting structure. 1. Verify that the intended installation surface has no hidden utility lines before drilling or driving
  • Harbor Freight Tools 61487 | User Manual - Page 7
    of the Rack without binding, and that the assembly and the Rack rotate freely all the way around the Column without binding. IF THE TABLE SUPPORT IS TOO TIGHT: • Slightly loosen the Table Lock Handle and loosen the Collar Set Screw. • Adjust the Collar slightly to provide a greater working clearance
  • Harbor Freight Tools 61487 | User Manual - Page 8
    SAFETy Head Assembly to column See Figure c. 1. Before installing the Head Assembly, it may be necessary to back the four Socket Head Cap Screws (6) out slightly to ensure they do not protrude internally, as this would prevent the Head Assembly from sliding fully into position. 2. With assistance,
  • Harbor Freight Tools 61487 | User Manual - Page 9
    SAFETy Installing the Belts 1. Undo the Belt Tension Locking Knobs (87) on both sides of the Head. Turn the Belt Tension Lever (97) clockwise to bring the Motor Pulley 109) towards the Spindle Pulley (69), allowing the Belts to be easily slipped over the Pulleys. 2. Lubricate the Idler Pivot Shaft
  • Harbor Freight Tools 61487 | User Manual - Page 10
    Functions SAFETy SETUp OpERATION MAINTENANcE Page 10 For technical questions, please call 1-800-444-3353. Item 61487
  • Harbor Freight Tools 61487 | User Manual - Page 11
    SAFETy SETUp Operating Instructions Read the ENTIRE IMpORTANT SAFETy INFORMATION section at the beginning of this manual including all lower the Table. 2. Swivel the Table around the column by loosening the Table Support Locking Handle. The table assembly, arm and rack (B), move as one around the
  • Harbor Freight Tools 61487 | User Manual - Page 12
    SAFETy SETUp changing Drill Speed See Functions on page 10 for illustrations. 1. WARNING! TO pREVENT SERIOUS INJURy: Turn off and unplug the Drill Press before changing drill speed. 2. Open the Pulley Cover. 3. Loosen the Belt Tension Lock Knobs on both sides of the Head and turn the Belt Tension
  • Harbor Freight Tools 61487 | User Manual - Page 13
    SAFETy Using the cutting Oil Drip System 1. Remove the upper Oil Bottle from the Oil Bottle Clips and unscrew the Cap. 2. Make sure that the Oil Pipe valve is closed. Fill the Bottle with your lubricant of choice. 3. Screw the Cap onto the Bottle and snap the Bottle back into the Clips. 4. Open
  • Harbor Freight Tools 61487 | User Manual - Page 14
    side of the column (see Figure H). Securely clamp the other end of the scrap wood to the table. Figure H: Bracing workpiece against column General Operating Instructions 1. Use the Spindle Feed Handles to bring the drill bit down to where the hole is to be drilled. Make minor workpiece alignment
  • Harbor Freight Tools 61487 | User Manual - Page 15
    Servicing procedures not specifically explained in this manual . If abnormal noise or vibration occurs, have the problem corrected before further use. cleaning, Maintenance, and Lubrication . 2. Replace belt if damaged, following the instructions under Installing the Belts on page 9. SETUp
  • Harbor Freight Tools 61487 | User Manual - Page 16
    SAFETy Adjusting the Spindle Feed Handle Return Torsion Spring This procedure must be performed only by a qualified technician. Wear a full face shield during this procedure. If the Spindle does not return all the way up or moves up sluggishly, or if it requires too much force to pull down on the
  • Harbor Freight Tools 61487 | User Manual - Page 17
    SAFETy Troubleshooting problem possible causes Likely Solutions Tool will not start. 1. Cord not connected. 2. before service. SETUp OpERATION MAINTENANcE pLEASE READ THE FOLLOWING cAREFULLy THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL
  • Harbor Freight Tools 61487 | User Manual - Page 18
    Handle Grip Gear Axis Pin Set Screw M5×10 Table Crank Nut M10 Table Crank Handle Socket Head Cap Screw M8×90 Worm Gear Table Support Table Support Arm Table Clamp Table Clamp Handle Spring Washer 16 Bolt M16×35 Sealing Gasket (B) Oil Bottle Cap Sealing Gasket (A) Hollow Connecting Bolt Oil Bottle
  • Harbor Freight Tools 61487 | User Manual - Page 19
    SAFETy SETUp Assembly Diagram 116 71 114 70 115 114 69 113 112 68 111 65 83 117 22 110 84 25 66 67 85 119 99 28 27 122 109 108 120 118 88 89 66 53 121 72 81 82 86 88 93 94 100 103 65 56 83 84 85 87 90 25 22 73 74 80 76 77 78 79 19 42 31 30 29 28 27 20 23
  • Harbor Freight Tools 61487 | User Manual - Page 20
    Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20